Zopec Medical Explore 4000 User manual

User Manual: Zopec Explore Travel Series CPAP/BiPAP Batteries (Ver. 02.05.2022)
Page 1 of 9
USER MANUAL
Models: 214000C, 215700C, 218200C

User Manual: Zopec Explore Travel Series CPAP/BiPAP Batteries (Ver. 02.05.2022)
Page 2 of 9
IMPORTANT – BEFORE FIRST USE
1. Initial Charge/Battery Reset: Please charge Zopec Explore battery (~8 hours) until
100% charged (LED = FF) before first use. Future charging will be faster. This is to
reset the battery capacity counter. It is normal if the capacity does not change for the
first 3 - 5 hours. See troubleshooting section if charging issues occur.
2. Heated Humidifier and Heated Tube Impact on CPAP Running Time:
• Longest Running Time: NOT using Heated Humidifier and Heated Tube.
• Shortest Running Time: Using Both Heated Humidifier and Heated Tube will
reduce about 75 - 80% of the CPAP running time.
• Heated Humidifier: With Heated Humidifier ON, it will reduce CPAP running
time by about 50 - 60%. It takes a lot of power to evaporate water.
• Heated Tube: We do not recommend running Heated Tube because it will
reduce CPAP running time by an additional 50 - 60%. In the US, water
shouldn’t pool in the CPAP hose. Please contact us if rain out is an issue.
3. Instruction for Turning Off the Heated Humidifier and Heated Tube:
• ResMed AirSense 10:
i. Go to “MyOptions” and change “ClimateControl” to “Manual”. NOTE:
this must be done first. Otherwise, the automatic climate control will
turn the heated humidifier and heated tube back ON without notice.
ii. Next, turn “Humidity Level” and “Tube Temp” to “OFF”. If you don’t
have a heated tube, just turn the “Humidity Level” to “OFF”.
iii. Exit “MyOptions” and re-enter “MyOptions” to verify that “Climate
Control” is in “Manual” and “Humidity Level” and “Tube Temp” are
“OFF”.
• Philips Respironics DreamStation, detach the heated humidifier and plug
the CPAP hose directly to the back of the CPAP Unit.
• All Other Machines, detach the heated humidifier if possible and just run the
CPAP unit. Please call or email us if you don’t know how to turn off your
heated humidifier and heated tube.
4. Determine the Exact CPAP Run Time: Test the run time with your machine and
exact settings first without sleeping with it. At the end of the CPAP hose, remove
your mask and put paper towel inside the CPAP hose. Turn the machine on and just
let a little air through the CPAP hose. This imitates breathing. Simply run the CPAP
with a fully charged battery during the day and record the run time.
5. Maintenance: Fully charge battery to 100% (LED = FF) monthly for maintenance.
6. Contact Us: We are proud to provide best-in class customer service so please
contact us with assistance any time. Below is our contact information:
• Zopec Medical Website: www.zopec.com
• Email: [email protected]
• Phone: Please see our website “Contact Us” for the current phone numbers.

User Manual: Zopec Explore Travel Series CPAP/BiPAP Batteries (Ver. 02.05.2022)
Page 3 of 9
Congratulations! You just purchased one of the most advanced travel CPAP and
BiPap batteries on the market! Below are key product features:
• Super Light and Compact
• 110V AC Outlet: It work with all CPAP machines without special adapters. No
more losing adapters during travel and unable to sleep. It can also run all
electronics with power requirement of 120W or under.
• Panasonic Lithium-Ion Technology: Panasonic brand is what Tesla vehicles
use and it enables the smallest, lightest, most efficient and longest life batteries.
• Uninterruptible Power Supply (UPS) Function: You will have uninterrupted
sleep in an event of power outage. (Note: This UPS pass-through was designed
for travel CPAP so Humidifier and Heated Tube MUST be turned OFF.)
• Unlimited Linking Technology: It can link up unlimited numbers to provide any
power needed and run BiPap or Humidifier.
• Universal Wall Charger Included: Can recharge battery worldwide.
• Fast Car Charger Included: You can charge the battery while driving or idle.
• Solar Panel Charger (not included): For a separate purchase, Zopec
PHOTONS Solar chargers allow fast remote charging.
Thank you for choosing Zopec Explore Batteries!
1. PRODUCT CONTENT
1. Zopec Explore Universal Travel CPAP Battery
2. Universal Wall Charger (48W AC Adapter with power cord)
3. Fast Car Charger (45W)
4. Protective Travel Pouch
5. User Manual
2. WARNINGS
• Do not drop the battery
• Keep battery dry and away from liquid
• Keep battery away from flammable and explosive materials
• Use only the Zopec Explore wall charger, car charger, and solar panel charger
• Do not disassemble the battery
• Do not use the battery beyond the operating temperatures (32 - 115°F (0 - 45°C))
• Follow the local regulations when disposing the battery

User Manual: Zopec Explore Travel Series CPAP/BiPAP Batteries (Ver. 02.05.2022)
Page 4 of 9
3. PRODUCT DIAGRAM
1. 110V AC Outlet
2. AC Outlet Indicator (Red LED Light: Red = ON, Dark = OFF)
3. Capacity % LED Display (“FF” = 100%)
4. Battery/AC Outlet Switch. (Press and Hold to turn on battery and show capacity
%, just press again to turn on AC Outlet. Press and Hold to turn the battery off.)
5. USB ports (2)
6. USB Type-C port
7. Cooling vent window
8. Recharging Port (DC In)
4. PRODUCT SPECIFICATIONS
Model Name
Explore 4000
Explore 5700
Explore 8200
Model Number
214000C
215700C
218200C
Medical Grade
Yes
Yes
Yes
UPS Function*
Yes
Yes
Yes
Unlimited Linking
Yes
Yes
Yes
Weight
2.0 lbs.
2.5 lbs.
3.5 lbs.
Dimensions (LxWxH)
7.5" x 5.5" x 1.0" (in)
8.5" x 6.0" x 1.0" (in)
7.5" x 5.5" x 1.5" (in)
Effective Battery Capacity
120 Wh
160 Wh
240 Wh
USB Type C (1 port)
15W (5V/3A)
15W (5V/3A)
15W (5V/3A)
USB Type A (2 ports)
15.5W (5V/3.1A)
15.5W (5V/3.1A)
15.5W (5V/3.1A)
AC Output
110V / 60 Hz
110V / 60 Hz
110V / 60 Hz
Working Temperature
32 - 115°F (0 - 45°C)
32 - 115°F (0 - 45°C)
32 - 115°F (0 -
45°C)
FAA/TSA Compliant
Yes (limit 2)
Yes (limit 2)
No
Recharge Time
4 hours or less
5 hours or less
6 hours or less
Battery Life (full/partial cycle)
500 / 2500
500 / 2500
500 / 2500
*Supports automatic backup power WITHOUT running heated humidifier and heated tube.

User Manual: Zopec Explore Travel Series CPAP/BiPAP Batteries (Ver. 02.05.2022)
Page 5 of 9
5. INSTRUCTION FOR USE
• Before first use, please charge battery to 100%. (LED = “FF”). To charge, first
plug the wall charger to the wall outlet. Next, connect the wall charger to the
battery Recharging port (DC In) on the side of the battery.
• To use the battery, you need to turn on the battery first and then the AC Outlet:
1. To turn on the battery, press and hold the Battery/AC Outlet Switch until
the Capacity % LED Display turns ON.
2. To turn on the AC Outlet, press and quick release the Battery/AC Outlet
Switch and the Red LED light of the AC Outlet Indicator turns ON.
• Plug in your device and the device should turn ON and be ready for use.
• After use, just press and hold the Battery/AC Outlet Switch to turn off (LED
Display turns off).
5.1 UNINTERRUPTIBLE POWER SUPPLY (UPS) FOR POWER OUTAGES
• The Heated Humidifier and Heated Tube MUST be OFF.
• To set up this backup power mode, just keep the battery charging while running
your machine. The AC Outlet must be ON with red LED light ON.
• When there is no power outage, the battery will run the wall power through a
Bypass (pass-through). Therefore, it does not hurt the battery life.
• When a power outage occurs, the battery senses the Bypass has zero current
flow and switches instantaneously to battery power. You would sleep through the
power outage uninterrupted without knowing a power outage occurred.
• Note: Please verify that the % capacity stays at 100% or “FF”. The Bypass
Technology does have a current limit. The Heated Humidifier and Heated Tube
MUST be OFF. Otherwise, your CPAP machine will start drawing power from the
battery. If you see the battery started to drain, then please turn the heated
humidifier and heated tube OFF.
• To save space on the nightstand or if the LED light bothers you, you can have
the battery on the floor or under the night stand. If you put in a drawer, make sure
it is vented. This battery comes with all safety features including over current,
over voltage, and over temp. It is safe to be on the floor. See below:

User Manual: Zopec Explore Travel Series CPAP/BiPAP Batteries (Ver. 02.05.2022)
Page 6 of 9
5.2 UNLIMITED LINKING TECHNOLOGY
• To get additional machine running time, you can purchase multiple batteries and
link them together. There is no limit on how many batteries you can link together.
Essentially, you can get any amount of power you want.
• To link 2 batteries, link up as you are recharge the first battery using the next
battery. Continue this set up to link more batteries. Please note that the CPAP
machine must plug into the first battery. It will draw from all batteries because
they are all linked.
• For backup power mode, just have the last battery in the link charging from a wall
outlet.
• Note: When drawing from multiple batteries, it doesn’t have a consistent order on
which battery it will draw first. That is normal. Every battery’s internal resistance
is different and your CPAP machine will draw power based on the path of least
resistance.
5.3 RECHARGING OPTIONS (WALL CHARGER, CAR CHARGER AND SOLAR
PANEL CHARGER)
• All charging plugs in to the recharging port of the battery.
• The wall charger is a universal power supply and works with all power sources
worldwide (100 – 240V, 50 – 60 Hz). You just need the outlet adapter to plug into
the outlet of that country.
• The car charger requires a 12V DC cigarette lighter or power outlet. For some
new cars, you may have a 110V outlet, you can use your wall charger to charge.
• Solar Panel Charger:
o The charging speed varies significantly with weather. A sunny, dry and
warm weather will charge the fastest. For example, a sunny and cold or
overcast weather will not charge nearly as efficiently.
o There are 3 solar panel options available: Zopec PHOTONS 40 Lite
(40W), 60 Pro (60W) and 100 Pro (100W). For hiking, we recommend the
40 Lite. For camping, we recommend the 60 Pro. For the 100 Pro, you can
choose this option if you plan to recharge in less than optimal weather
conditions.

User Manual: Zopec Explore Travel Series CPAP/BiPAP Batteries (Ver. 02.05.2022)
Page 7 of 9
6. BATTERY RUN TIME TABLE
Machine
Brand
Machine
Model
Pressure
(cm H2O)
Heated
Humidifier
Heated
Tube
Explore
4000
(Hours)
Explore
5700
(Hours)
Explore
8200
(Hours)
ResMed
AirSense
AutoSet
10 or 11
10
OFF
OFF
12.5
17
25
15
OFF
OFF
10.5
14
21
10
On (4)
OFF
6
8
12
15
On (4)
OFF
4.5
6
9
AirCurve 10
VAUTO BiPap
IPAP=20,
EPAP=15
OFF
OFF
9.5
13
19.5
IPAP=20,
EPAP=15
On (4)
OFF
4
5
7.5
AirMini
10
OFF
OFF
15
20
30
15
OFF
OFF
13.5
18
27
Philips
Respironics
DreamStation
Auto 1 or 2
10
OFF
OFF
16
21
32
15
OFF
OFF
12
16
24
10
On (3)
OFF
6
8
12
15
On (3)
OFF
4.5
6
9
DreamStation
BiPap
IPAP=20,
EPAP=15
OFF
OFF
9.5
13
19.5
IPAP=20,
EPAP=15
On (3)
OFF
4
5
7.5
DreamStation
Go
10
OFF
OFF
16
22
32
15
OFF
OFF
12.5
16.5
25
3B Medical
Luna/G3
Series
10
OFF
OFF
13
18
26
Resvent
iBreeze Series
10
OFF
OFF
13
18
26
Breas HDM
Z1 / Z2
10
OFF
OFF
16
24
32
Drive
DeVilbiss
IntelliPap I / II
10
OFF
OFF
13
18
26
Beyond
ResPlus
10
OFF
OFF
13
18
26
Apex
Medical
XT and iCH II
10
OFF
OFF
10
14
20
Somnetics
Transcend/360
10
OFF
OFF
16
24
32

User Manual: Zopec Explore Travel Series CPAP/BiPAP Batteries (Ver. 02.05.2022)
Page 8 of 9
7. TROUBLESHOOTING
• Battery Will Not Charge or Would Not Hold Charge:
o Please press and hold the Battery ON/OFF switch for 20 seconds then try
charging again. Go to next step if it still won’t charge.
o This is a high-capacity lithium-ion battery and sometimes it takes 2 – 3
depletion cycles to reset the battery. Please run your CPAP machine with
humidifier or device at max until the CPAP or device turns off. This
depletes the battery. Please try charging again.
• Battery Run Time Not Lasting as Long: Please make sure to follow the
instructions in this manual to turn off the heated humidifier and heated tube then
try again. If you have a ResMed CPAP machine, most likely the automatic
ClimateControl turned the heated humidifier and heated tube back ON without
you knowing. Please enter “MyOptions” and make sure the Climate Control is in
“Manual” before turning the humidity level and tube temp to OFF, then try again.
• No Power to the AC Outlet: Please follow the instruction to turn ON the battery
and the AC outlet. Please make sure that the red LED is ON, which means the
AC Outlet is ON. If the red LED light is ON and there is no power to the AC
Outlet, then please contact us for further assistance.
• Electrical Sparks: When you plug into the recharging port or the AC Outlet, you
may see occasional sparks. That is typically from static electricity and is normal.
It is fast and will not harm you or the battery. To avoid it, you can try grounding
yourself by touching a large metal surface before recharging or plugging your
device into the battery.
With unresolved problems, please contact your vendor or us for further assistance.
8. LIMITED WARRANTY
Zopec Medical warrants that your purchased product shall be free from defects in
material and workmanship from the date of purchase for the period specified below:
1. Zopec Explore Batteries: 1 year
2. Solar Panel Charger: 1 year
3. Wall Charger: 1 year
4. Car Charger: 1 year
Our Limited Warranty is only valid when the defective item is accompanied by a proof of
purchase. Please note our warranty does not cover product failure that is caused by
user negligence such as water, physical, and disassembling damages. If we determine
that it is warranty eligible, then a new replacement will be provided.
For all warranty claims, please contact the original seller and they will work with us on
the proper warranty claim process.

User Manual: Zopec Explore Travel Series CPAP/BiPAP Batteries (Ver. 02.05.2022)
Page 9 of 9
9. CONTACT US
We are proud to provide best-in class customer service so please contact us with
assistance any time. Below is our contact information:
• Zopec Medical Website: www.zopec.com
• Email: [email protected]
• Phone: Please see our website “Contact Us” for the current phone numbers.
END OF USER MANUAL.