Zotac GeForce 9300-ITX User manual

1
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with instructions
contained in this manual, may cause harmful interference to radio and television communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- REORIENT OR RELOCATE THE RECEIVING ANTENNA
- INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER
- CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM
THAT OF THE RECEIVER
- CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN
NOTE:
Connecting this device to peripheral devices that do not comply with Class B requirements, or
using an unshielded peripheral data cable, could also result in harmful interference to radio or
television reception.
The user is cautioned that any changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
To ensure that the use of this product does not contribute to interference, it is necessary to use
shielded I/O cables.
Copyright
This manual is copyrighted with all rights reserved. No portion of this manual may be copied or
reproduced by any means.
While every precaution has been taken in the preparation of this manual, no responsibility for
errors or omissions is assumed. Neither is any liability assumed for damages resulting from the
use of the information contained herein.
Trademarks
All brand names, logos and registered trademarks mentioned are property of their respective
owners.
Electronic Emission Notices
WARNING!

2
GeForce 9300/9400 ITX Series Motherboard
Table of Contents
Motherboard Specications ------------------------------------------------------------------- 4
Motherboard Layout------------------------------------------------------------------------------ 6
Hardware Installation ---------------------------------------------------------------------------- 8
Safety Instructions ----------------------------------------------------------------------------- 8
Preparing the Motherboard ------------------------------------------------------------------ 9
Installing the CPU ------------------------------------------------------------------------------ 9
Installing the CPU Fan ------------------------------------------------------------------------ 9
Installing Memory DIMMs -------------------------------------------------------------------- 10
Installing the Motherboard ------------------------------------------------------------------- 11
Installing the I/O Shield ----------------------------------------------------------------------- 11
Connecting Cables and Setting Switches ------------------------------------------------ 11
24-pin ATX Power Connector-PW1---------------------------------------------------- 12
4-pin ATX 12V Power Connector-PW2 ----------------------------------------------- 12
Speaker Header-SPK --------------------------------------------------------------------- 13
Serial Port Header-COM ----------------------------------------------------------------- 13
USB Headers ------------------------------------------------------------------------------- 13
Front Panel Header-FP1 ----------------------------------------------------------------- 14
SPDIF-out Header ------------------------------------------------------------------------- 14
Front Audio Header-FP_S1 ------------------------------------------------------------- 15
Serial-ATA (SATA) Connectors --------------------------------------------------------- 15
Fan Connectors ---------------------------------------------------------------------------- 16
Expansion Slots ---------------------------------------------------------------------------- 16
PCI Express x16 Slots ---------------------------------------------------------------- 16
Jumper Settings ---------------------------------------------------------------------------- 16
Conguring the BIOS ---------------------------------------------------------------------------- 17
Enter BIOS Setup ----------------------------------------------------------------------------------- 17
Main Menu --------------------------------------------------------------------------------------- 18
Advanced Menu -------------------------------------------------------------------------------- 19
CPU Conguration ------------------------------------------------------------------------ 19
IDE Conguration ------------------------------------------------------------------------- 20
ACPI Conguration ----------------------------------------------------------------------- 20
APM Conguration ------------------------------------------------------------------------ 20
MPS Conguration ------------------------------------------------------------------------ 20
PCI Express Conguration ------------------------------------------------------------- 20
Smbios Conguration -------------------------------------------------------------------- 20
USB Conguration ------------------------------------------------------------------------ 20
Boot Menu --------------------------------------------------------------------------------------- 21
Boot Settings Conguration ------------------------------------------------------------- 21
Chipset Menu ----------------------------------------------------------------------------------- 22

3
Table of Contents
NorthBridge/MCP79 Conguration --------------------------------------------------- 22
SouthBridge Conguration -------------------------------------------------------------- 22
PC Health Menu -------------------------------------------------------------------------------- 23
Exit Menu----------------------------------------------------------------------------------------- 23
Installing Drivers and Software -------------------------------------------------------------- 25
Drivers Installation ---------------------------------------------------------------------------- 25
HDMI SETUP ----------------------------------------------------------------------------------- 28
Realtek HD Audio Driver Setup ------------------------------------------------------------ 29
Getting Started ----------------------------------------------------------------------------- 29
Sound Effect -------------------------------------------------------------------------------- 29
Environment Simulation ------------------------------------------------------------ 29
Equalizer Selection ------------------------------------------------------------------ 30
Frequently Used Equalizer Setting ----------------------------------------------- 30
Karaoke Mode ------------------------------------------------------------------------- 30
Mixer ------------------------------------------------------------------------------------------ 31
Playback control ---------------------------------------------------------------------- 31
Recording control --------------------------------------------------------------------- 32
Audio I/O ------------------------------------------------------------------------------------- 33
Speaker Conguration -------------------------------------------------------------- 34
Connector Settings ------------------------------------------------------------------- 35
S/PDIF ---------------------------------------------------------------------------------- 35
Speaker Calibration ------------------------------------------------------------------ 36
Microphone---------------------------------------------------------------------------------- 37
Noise Suppression ------------------------------------------------------------------- 37
Beam Forming ------------------------------------------------------------------------ 37
Acoustic Echo Cancellation -------------------------------------------------------- 37
Audio Demo --------------------------------------------------------------------------------- 38
Information ---------------------------------------------------------------------------- 38
SATA RAID User Manual ------------------------------------------------------------------------ 39
Setting up the BIOS --------------------------------------------------------------------------- 39
Entering the RAID BIOS Setup ------------------------------------------------------------- 40
Installing the RAID Drives -------------------------------------------------------------------- 41

4
GeForce 9300/9400 ITX Series Motherboard
Motherboard Specications
q Chipset
v NVIDIA® MCP7A Series
q Size
v mini ITX form factor of 6.7 inch x 6.7 inch
q Microprocessor support
v LGA 775 socket for Intel® CoreTM 2/Pentium®/Celeron® Series
v Supports a system bus (FSB) of 1333/1066/800 MHz
q Operating systems:
v Supports Windows XP 32bit/64bit, Windows Vista 32bit/64bit and Windows 7
32bit/64bit
q System Memory support
v Supports dual-channel (128 bits wide) DDRIII memory interface
v Supports DDR3 1333/1066
v Maximum memory size: 8 GB
q USB 2.0 Ports
v Supports hot plug and play
v Twelve USB 2.0 ports (six rear panel ports, six from onboard USB headers)
v Supports USB 2.0 protocol up to 480 Mbps transmission rate
v Support USB wake up from S3
q Onboard Serial ATA II
v Three SATA II ports
v Independent DMA operation
v Data transfer rates of 3.0 Gb/s
q On board RTL8211CL Gigabit LAN (Optional)
v Supports 10/100/1000 Mbps operation
q On board RTL8201EL Fast Ethernet (Optional)
v Supports 10/100 Mbps operation
v Supports half/full duplex operation
q Onboard Audio (Optional)
v Azalia High-Denition audio
v Supports 6-channel
v Supports Jack-Sensing function
q Green Function
v Supports ACPI (Advanced Conguration and Power Interface)
v RTC timer to power-on the system
v AC power failure recovery

5
Motherboard Specications
q Onboard Graphics support
v Integrated 300 MHz DAC for analog displays with resolutions up to 1920x1440
at 75 Hz.
v Integrated GeForce 9xxx Series GPU, Supports DX10
v VGA/DVI-D/HDMI output support (optional)
q PCI Express Interface
v PCI Express Generation 2.0 compatible
v 5 GHz support, for a total bandwidth of 5 Gbps per direction per lane
v Wake up function is supported
v Clock spread spectrum capability
q Integrated HDMI Interface with HDCP
v Support Dual link DVI, resolutions up to 2560x1600
v Supports DVI or HDMI 1.3 interfaces
v Secure digital audio merged from integrated HDA codec with no external audio
signals required
v Support for HDCP 1.3 using soft or hard HDCP keys
v HDCP encryption support when congured as DVI or HDMI link without the
need for external HDCP key crypto ROM
q Dual Head Display Controller
v Full NVIDIA nView™ multi-display technology capability, with independent
display controllers for the CRT, TMDS, DisplayPort, and HDMI interface
v Each controller can drive same or different display contents to different resolu-
tions and refresh rates
q Expansion Slots
v One PCI Express x16 slot

6
GeForce 9300/9400 ITX Series Motherboard
Motherboard Layout
Figure 1 shows the motherboard and Figure 2 shows the back panel connectors.
Figure 1. Board Layout
120 240
121
120 240
121
LOTES
R E O EVM
+
Chipset
DDRIII1
DDRIII3
PW1
S FAN1_
FP1
SATA1
SATA2
COM
PCIE1
C FAN1_
FP S1_
USB
USB
USB
JP1
PW2
HDMI
VGA/DVI
USB/eSATA
LAN USB/
SD1 KB
USB/
SPDIF
2
3
4
56
8
97
1011
12
13 14
15 16
SPK
17
SATA3
18
JP2
SPDIF
19
JP3
1. 24-pin ATX Power Connector-PW1
2. System Fan Connector-S_FAN1
3. Front Panel Header-FP1
4. Speaker Header-SPK
5. SPDIF-out Header-SPDIF
6. Serial-ATA (SATA) Connectors-SATA1~3
7. PCI Express x16 Slot-PCIE1
8. Serial Port Header-COM
9. BIOS Selection Jumper-JP3 (Optional)
10. Clear CMOS Jumper-JP1
11. Front Audio Header-FP_S1
12. Backpanel Connectors
13. 4-pin ATX_12V Power Connector-PW2
14. CPU Fan Connector-C_FAN1
15. USB Power Select Jumper-JP2
16. USB Headers
17. CPU Socket
18. Chipset
19. DDRIII DIMM Sockets

7
Rear Panel
7. Port 2-Channel 4-Channel 6-Channel
Blue Line-In Rear Speaker Out Rear Speaker Out
Green Line-Out Front Speaker Out Front Speaker Out
Pink Mic In Mic In Center/Subwoofer
8. LAN Connector
Lan Port with LEDs to indicate status.
· Yellow/Light Up/Blink = 10 Mbps/Link/Activity
· Yellow and Orange/Light Up/Blink = 100 Mbps/link/Activity
· Yellow and Orange/Light Up/Blink = 1000 Mbps/link/Activity
9. VGA Port
Figure 2: Backpanel connectors
1. PS/2 keyboard connector
2. USB Connectors
3. HDMI Port
4. SPDIF Out(Coaxial / Optical)
5. DVI Connector (Support DVI-D)
6. eSATA Connector
6
11
5
10
15
7
2 2
3456
8
9

8
GeForce 9300/9400 ITX Series Motherboard
Hardware Installation
This section will guide you through the installation of the motherboard. The topics
covered in this section are:
q Preparing the motherboard
v Installing the CPU
v Installing the CPU fan
v Installing Memory DIMMs
q Installing the motherboard
q Connecting cables and setting switches
Safety Instructions
To reduce the risk of re, electric shock, and injury, always follow basic safety precautions.
Remember to remove power from your computer by disconnecting the AC main
source before removing or installing any equipment from/to the computer chassis.

9
Hardware Installation
Preparing the Motherboard
The motherboard shipped in the box does not contain a CPU and memory. You need
to purchase these to complete this installation.
Installing the CPU
Be very careful when handling the CPU. Make sure not to bend or break any pins on
the back. Hold the processor only by the edges and do not touch the bottom of the
processor.
Use the following procedure to install the CPU onto the motherboard.
1. Unhook the socket lever by pushing down and
away from the socket.
2. Lift the load plate. There is a protective socket
cover on the load plate to protect the socket
when there is no CPU installed.
3. Remove the protective socket cover from the
load plate.
4. Remove the processor from its protective cover,
making sure you hold it only by the edges.
It is a good idea to save the cover so that
whenever you remove the CPU, you have a
safe place to store it.
5. Align the notches in the processor with the
notches on the socket.
6. Lower the processor straight down into the
socket with out tilting or sliding it into the socket.
Note:MakesuretheCPUisfullyseatedand
levelinthesocket.
7. Close the load plate over the CPU and press
down while you close and engage the socket
lever.
Installing the CPU Fan
There are many different fan types that can be used with this motherboard. Follow the
instruction that came with your fan assembly. Be sure that the fan orientation is correct
for your chassis type and your fan assembly.

10
GeForce 9300/9400 ITX Series Motherboard
120 240
121
120 240
121
LOTES
R E O EVM
+
Installing Memory DIMMs
Your new motherboard has two 1.5V 240-pin slots for DDR3 memory. These slots
support 1 GB/2 GB/4 GB DDR3 technologies. There must be at least one memory
bank populated to ensure normal operation. Use the following recommendations for
installing memory. (See Figure 1 for the location of the memory slots.)
q One DIMM:You can install the DIMM into any slot.
q Two DIMMs:Install into slot 1 and slot 2. The idea is to run on dual channel
mode.
Use the following procedure to install memory DIMMs into the slots on the mother-
board. Note that there is only one gap near the center of the DIMM slot. This slot
matches the slot on the memory DIMM to ensure the component is installed properly.
1. Unlock a DIMM slot by pressing the module clips outward.
2. Align the memory module to the DIMM slot, and insert the module vertically into
the DIMM slot. The plastic clips at both sides of the DIMM slot automatically lock
the DIMM into the connector.
DDRIII3
DDRIII1

11
Hardware Installation
Installing the Motherboard
The sequence of installing the motherboard into the chassis depends on the chassis
you are using and if you are replacing an existing motherboard or working with an
empty chassis. Determine if it would be easier to make all the connections prior to this
step or to secure the motherboard and then make all the connections. It is normally
easier to secure the motherboard rst.
Use the following procedure to install the I/O shield and secure the motherboard into
the chassis.
Note:BesurethattheCPUfanassemblyhasenoughclearanceforthechassis
coverstolockintoplaceandfortheexpansioncards.Alsomakesurethe
CPUFanassemblyisalignedwiththeventsonthecovers.
Installing the I/O Shield
The motherboard kit comes with an I/O shield that is used to block radio frequency
transmissions, protects internal components from dust and foreign objects, and
promotes correct airow within the chassis.
Before installing the motherboard, install the I/O shield from the inside of the chassis.
Press the I/O shield into place and make sure it ts securely. If the I/O shield does not
t into the chassis, you would need to obtain the proper size from the chassis supplier.
Connecting Cables and Setting Switches
This section takes you through all the connectors and switch settings necessary on
the motherboard. This will include:
q Power Connectors
v 24-pin ATX Power Connector-PW1
v 4-pin ATX 12V Power Connector-PW2
q Internal Headers
v Speaker Header-SPK
v Serial Port Header-COM
v USB Headers
v Front panel header-FP1
v SPDIF-Out Header
v Front Audio Header-FP_S1
q Serial-ATA
q Chassis Fans
q Expansion slots
q Jumper settings

12
GeForce 9300/9400 ITX Series Motherboard
24-pin ATX Power Connector-PW1
PW1 is the main power supply connector located along the edge of the board next to
the DIMM slots. Make sure that the power supply cable and pins are properly aligned
with the connector on the motherboard. Firmly plug the power supply cable into the
connector and make sure it is secure.
120 240
121
120 240
121
LOTES
R E O EVM
+
4-pin ATX 12V Power Connector-PW2
PW2, the 4-pin ATX 12V power connector, is used
to provide power to the CPU. Align the pins to the
connector and press rmly until seated.
PW1-Pin Assignments
Pin Signal Pin Signal
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PS_ON
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 PWROK 20 -5V
9 +5V_AUX 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 GND
1
12 13
24
PW1
1
PW2
PW2-Pin Denition
Pin Signal
1 GND
2 GND
3 +12V
4 +12V

13
Hardware Installation
USB Headers
This motherboard contains six USB 2.0
ports that are exposed on the rear panel
of the chassis (Figure 2). The motherboard
also contains three 10-pin internal headers
onboard.
Note. Secure the bracket to either the
frontorrearpanelofyourchassis(not
allchassisareequippedwiththefront
paneloption).
USB-Pin Denition
PIN Assignment PIN Assignment
1 VCC 6 USBP1+
2 VCC 7 GND
3 USBP0- 8 GND
4 USBP1- 9 KEY
5 USBP0+ 10 OC#
120 240
121
120 240
121
LOTES
R E O EVM
+
COM
1
2
9
10
1
SPK
1
9 10
21
9 10
2 1
9 10
2
USB
Speaker Header-SPK Serial Port Header-COM
SPK-Pin Denition
Pin Signal
1 VCC
2 NC
3 NC
4 SPK-
COM-Pin Denition
Pin Signal Pin Signal
1 DCD 6 DSR
2 RXD 7 RTS
3 TXD 8 CTS
4 DTR 9 RI
5 GND 10 NC

14
GeForce 9300/9400 ITX Series Motherboard
Front panel header-FP1
The front panel header on this motherboard is one connector used to connect the
following four cables.
q PWRLED
Attach the front panel power LED cable to these two pins of the connector. The
Power LED indicates the system’s status.
q PWR SW
Attach the power button cable from the case to these two pins. Pressing the
power button on the front panel turns the system on and off rather than using the
power supply button.
q HDD LED
Attach the hard disk drive indicator LED cable to these two pins. The HDD
indicator LED indicates the activity status of the hard disks.
q RST SW
Attach the Reset switch cable from the front panel of the case to these two pins.
The system restarts when the RESET switch is pressed.
Note:Somechassisdonothaveallfourcables.
Besuretomatchthenameontheconnectors tothecorrespondingpins.
FP1-Pin Denition
Pin Signal Pin Signal
1 HDD_LED+ 6 PWR_SW
2 PW_LED+ 7 RESET
3 HDD_LED- 8 GND
4 PW_LED- 9 NC
5 GND 10 KEY
SPDIF-Out Header
This header provides a SPDIF-Out
(Sony/Philips Digital Interface) to
digital multimedia device through
coaxial connector.
SPDIF-Pin Denition
Pin Signal
1 SPDIF OUT
2 VCC
3 NC
4 GND
120 240
121
120 240
121
LOTES
R E O EVM
+
12
910
FP1
1
SPDIF

15
Hardware Installation
Front Audio Header-FP_S1
The audio connector supports HD audio standard and provides two kinds of audio
output choices: the Front Audio, the Rear Audio. The front Audio supports re-tasking
function.
Note:
Inordertoutilizethefrontaudioheader,yourchassismusthavefrontaudio
connector.Alsopleasemakesurethepinassignmentonthecableisthe
sameasthepinassignmentonthemainboardheader.Tondoutifthe
chassisyouarebuyingsupportsafrontaudioconnector,pleasecontract
yourdealer.
120 240
121
120 240
121
LOTES
R E O EVM
+
2
1
10
9
FP_S1
FP_S1-Pin Denition
PIN Assignment PIN Assignment
1 MIC2(L) 6 Reserved
2 GND 7 FAVDIO-JD
3 MIC(R) 8 Key(No pin)
4 -ACZ-DET 9 Front Audio(L)
5 Front Audio(R) 10 Reserved
Serial-ATA (SATA) Connectors-SATA1~3
The Serial ATA II connector is used to connect the Serial ATA II device
to the motherboard. These connectors support the thin Serial ATA II
cables for primary storage devices. The current Serial ATA II interface
allows up to 3.0 Gb/s data transfer rate.
There are three Serial ATA II connectors on the motherboard that
support AHCI and RAID congurations.
SATA-Pin Denition
Pin Signal
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
SATA 3
1
SATA 1SATA 2
1 1

16
GeForce 9300/9400 ITX Series Motherboard
120 240
121
120 240
121
LOTES
R E O EVM
+
Fan Connectors
There are two fan connectors on the motherboard. The fan speed can be detected
and viewed in the item “MCP HW Monitor” which is inside PC Health of the CMOS
Setup. CPU FAN Connector
GND
+12V
Sense
Control
SYS FAN Connector
Sense
+12V
GND
Expansion Slots
The NVIDIA® MCP7A motherboard contains one
expansion slot, PCI Express x16 graphics card
supported by this motherboard.
PCI Express x16 Slot-PCIE1
There is one PCI Express x16 slot reserved for
graphics or video cards. The bandwidth of the
PCI Express x16 slot is up to 8 GB/sec compli-
anting with PCIE 2.0 specication.
PCI Express x 16 slot
Jumper Settings
This chapter explains how to congure the motherboard’s hardware. Before using your
computer, make sure all jumpers and DRAM modules are set correctly. Refer to this
chapter whenever in doubt.
Notice:
1. Be sure to save the CMOS setting when exit the CMOS.
2. If the CPU is frequency multiplier locked, no CPU speed change will be seen
even if the frequency multiplier setting in CMOS setup is changed.
Close Open * = Default setting.
1. If you want to clear the system conguration, use
the JP1(Clear CMOS Jumper) to clear data.
2. If you want to USB wake up, please select power
to 5Vdual
CMOS Clear Jumper-JP1
JP1 Selection
1-2* Normal*
2-3 CMOS Clear
1
1
JP2 Selection
1-2* 5Vdual(for USB wake up support) *
2-3 5V
1
1
USB Power select-JP2
BIOS Selection Jumper-JP3 (Optional)
JP3 Selection
1-2* Master*
3-4 Backup
5-6 Use factory BIOS
1
2
5
6
1
2
5
6
1
2
5
6

17
Conguring the BIOS
Conguring the BIOS
This section discusses how to change the system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS parameters are also provided.
Enter BIOS Setup
The BIOS is the communication bridge between hardware and software. Correctly
setting the BIOS parameters is critical to maintain optimal system performance.
Use the following procedure to verify/change BIOS settings.
1. Power on the computer.,
2. Press the Del key when the following message briey displays at the bottom of
the screen during the Power On Self Test (POST).
Pressing Del takes you to the BIOS Setup Utility.
Note: ItisstronglyrecommendedthatyoudonotchangethedefaultBIOS 
  settings.Changingsomesettingscoulddamageyourcomputer.

18
GeForce 9300/9400 ITX Series Motherboard
Main Menu
This menu gives you an overview of the general system specications. The BIOS
automatically detects the items in this menu.

Note: Userspleasenotethatthedataingrayisnon-changeable,andtheothers
areforselection.
q AMI BIOS
Displays the auto-detected BIOS information.
q Processor
Display the auto-detected CPU specication.
q System Memory
Displays the auto-detected system memory.
q System time
Allows you to set the system time.

19
Conguring the BIOS
Advanced Menu
The Advanced menu items allow you to change the setting for the CPU and other
system devices. Press <enter> to display the conguration options:
CPU Conguration
The items in this menu show the CPU-related information that the BIOS automatically
detects. Press <enter>to display the conguration options:
q Congure advanced CPU settings
Displays the auto-detected CPU information
q Hardware Prefetcher
Use this item to enable or disable hardware prefetcher (hardware prefetch
mechanism).
q Adjacent Cache Line Prefetch
Use this item to enable or disable the adjacent cache line prefetch mode. If you
disable this item, only one 64-bit line will be prefetched from the 128-bit section
(including the required data). If you enable this item, two lines will be prefetched
whether there is required data or not.
q Max CPUID Value Limit
Allows you to determine whether to limit CPUID maximum value. Set this item
to [Disable] Windows XP operating system; set this item to [Enable] for legacy
operating system such as Windows NT4.0..
q Intel(R) Virtualization Tech
When enable, avMM can utilize the additional HW caps, provided by Intel®
Virtualization Tech.
q Execute-Disable Bit Capability
This function enhances protection of your computer , reducing exposure to viruses
and malicious buffer overow attacks when working with its supporting software
and system.
q Core Multi-Processing
Use this option to enable or disable Core Multi-Processing.
q PECI
Use this option to enable or disable PECI (Platform Environment Control Interface).
q Intel(R) SpeedStep(tm) tech
Use this option to enable or disable Intel® SpeedStepTM Technology.
q Intel(R) C-STATE tech
Use this option to enable or disable Intel® C-STATE Technology.