Zotac nForce 610i Value User manual

1
Electronic Emission Notices
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with instructions contained in this manual, may cause harmful
interference to radio and television communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- REORIENT OR RELOCATE THE RECEIVING ANTENNA
- INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER
- CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM
THAT OF THE RECEIVER
- CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN
NOTE: Connecting this device to peripheral devices that do not comply with Class B
requirements, or using an unshielded peripheral data cable, could also result in
harmful interference to radio or television reception.
 Theuseriscautionedthatanychangesormodicationsnotexpresslyapproved
by the party responsible for compliance could void the user’s authority to
operate this equipment.
To ensure that the use of this product does not contribute to interference, it is
necessary to use shielded I/O cables.
Copyright
This manual is copyrighted with all rights reserved. No portion of this manual may be
copied or reproduced by any means.
While every precaution has been taken in the preparation of this manual, no responsibility
for errors or omissions is assumed. Neither is any liability assumed for damages resulting
from the use of the information contained herein.
Trademarks
All brand names, logos and registered trademarks mentioned are property of their
respective owners.

2
Technical Reference Booklet
TABLE OF CONTENTS
HARDWARE CONFIGURATION..................................................................4
Key Features..................................................................................................4
MOTHERBOARD LAYOUT ........................................................................7
REAR PANEL ...............................................................................................8
AUDIO CONFIGURATION............................................................................9
JUMPER SETTING.......................................................................................10
CMOS Clear - JP1 ...................................................................................10
P/S Port 5V Standby Power Selection - JP2 ...........................................10
CONNECTORS .............................................................................................11
Floppy Disk Drive Connector - CN3.........................................................11
Hard Disk Connectors - CN1 ...................................................................11
Serial ATA Hard Disk Connectors -
SATA1, SATA2, SATA3, SATA4 ............................................................. 12
Fan Power Connectors -
CPU FAN/SYS FAN1 ............................................................................. 13
Front Panel Audio Header - FP_S1 .........................................................14
USB Connectors - FP_U1/FP_U2 ...........................................................15
SPDIF Out Header - CN7(optional) ...................................................... 16
CD-IN Connector - CD1(optional); Speaker Connector - SPK ...............17
Front Panel Headers - FP1......................................................................18
SLOTS...........................................................................................................19
CPU INSTALLATION....................................................................................20
INSTALL DDRII DIMMS...............................................................................24
BIOS SETUP ................................................................................................25
About the Setup Utility .............................................................................25
Main Menu ...............................................................................................26
Standard CMOS Features .......................................................................26
Advanced BIOS Features ........................................................................26
Advanced Chipset Features ....................................................................26
Integrated Peripherals .............................................................................26
Power Management Setup ......................................................................26

3
 PNP/PCICongurations ..........................................................................26
PC Health Status .....................................................................................26
Frequency/Voltage Control ......................................................................27
Load Fail-Safe Defaults ...........................................................................27
Load Optimized Defaults .........................................................................27
Set Supervisor/User Password................................................................27
 Save&ExitSetup....................................................................................27
 ExitWithoutSaving..................................................................................27
Flash Update Procedure..........................................................................30
REALTEK HD AUDIO DRIVER SETUP........................................................31
Getting Started.........................................................................................31
Sound Effect ............................................................................................31
Environment Simulation...........................................................................31
Equalizer Selection ..................................................................................32
Frequently Used Equalizer Setting ..........................................................32
Karaoke Mode .........................................................................................32
 Mixer ........................................................................................................33
Playback control.................................................................................33
Recording control ...............................................................................34
Audio I/O ............................................................................................35
  SpeakerConguration .......................................................................36
Global Connector Settings .................................................................37
S/PDIF................................................................................................37
Speaker Calibration............................................................................38
Microphone ........................................................................................39
Noise Suppression .............................................................................39
Beam Forming....................................................................................39
Acoustic Echo Cancellation................................................................39
Audio Demo .......................................................................................40
Information .........................................................................................40
SATA RAID User Manual .............................................................................41
Setting up the BIOS .................................................................................41
Entering the RAID BIOS Setup................................................................43
Installing the RAID Drivers.......................................................................46

4
Technical Reference Booklet
HARDWARE CONFIGURATION
Key Features :
Chipset
• NVIDIA MCP73V.
Processor
• Supports Intel® Celeron® , Pentium® 4, Pentium® D, CoreTM 2 Duo
processors in the LGA775 -pin package (with 0.8V~1.6V voltage).
• Supports PSB (Processor System Bus) frequency of 533MHz/800MHz/
1066MHz.
• Supports Hyper-Threading Technology.
System Memory
• Two DIMM sockets support.
• 64-bit single-channel DDRII SDRAM interface.
• Supports up to 4GB(2*2GB) DRAMs.
• Supports DDRII533/DDRII667 SDRAM memory types.
• 1.8V DRAM interface for DDRII SDRAM.
Onboard I/O
• Onboard one PCI fast IDE port supporting up to 2 ATA, ATA2 , Ultra
ATA33/66/100/133 IDE HDDs, CD-ROMs, ZIP drives and LS-120
drives as boot drive.
• Oneoppyport,supportstwoFDDof360KB,720KB,1.28MB,1.44MB,
and 2.88MB capacity.
• PS/2 keyboard connector.
• PS/2 mouse is supported.
• One ECP/EPP parallel port.
• One 16550 Compatible UART serial port.
• One Front Panel Sound Connector.
• Eight USB ports.
System BIOS
•PnP, APM, ATAPI and Windows 2000/XP/Vista.
•Full support of ACPI & DMI.
• Easy to upgrade BIOS by end-user.
Onboard Fast Ethernet Controller
• The RTL8201CL supports 10Mb/s &100Mb/s.
• One RJ45 Port.

5
Plug-and-Play
 • SupportsPlugandPlayspecication1.1.
• Plug and Play for Windows2000/XP/Vista.
• Fully steerable PCI interrupts.
Power Management
•Support SMM, APM, ACPI
•Break switch for instant suspend/resume on system operations.
•Energy star “ Green PC ” compliant.
•Hardware monitoring circuit is supported, provide voltage, fan speed,
etc. monitoring(optional).
• Support STR(suspend to RAM)(optional)
Onboard ALC662 5.1 Audio(optional)
•Integrated Realtek ALC888 controller.
•Full Direct Sound and Sound Blaster compatibility.
•Full-Duplex424-bittwo-channelDACsand3stereo20-bitADCs.
•PnP and APM 1.2 support.
•Windows® 2000/XP/Vista ready.
•Supports Line-in, Line-out, Mic-in, SPDIF-out.
•Supports ALC662 codec for eight channel sound output.
Onboard Serial ATA Host Controller
•Independent DMA operation on four ports(optional).
•Supports SATAII
•Data transfer rates of 300MB/s.
•RAID 0, RAID 1, RAID 0+1, RAID 5 JBOD feature support.
Expanded USB Support
• Supports up to eight USB ports.
• Supports USB2.0.
• Supports transfer rates at high speed (480 Mb/s), full speed
(12Mb/s), and low speed (1.2Mb/s).
• This motherboard support USB2.0 only Windows® 2000 (with SP4
or above), Windows® XP (with SP1 or above) and above operating
systems.
PCIE x 1 Controller
• FullycomplianttothePCIExpressBaseSpecicationrevision1.0a.
• One virtual channel support for full unsynchronized data transfers.
 • Supportsfull2.5Gb/sbandwidthineachdirectionperx1lane.

6
Technical Reference Booklet
Static electricity can harm delicate components of the motherboard.
To prevent damage caused by static electricity, discharge the static
electricity from your body before you touch any of the computers
electronic components.
PCI Express Graphics interface
•OneX16slotPCIExpressgraphicsport.
•FullycompliantwiththePCIExpressBaseSpecicationrevision1.0a.
•ThebasePCIExpressfrequencyofthisinterfaceis4GB/s.
•PCIExpresssupportandEnhancedAddressingMechanism.
Onboard VGA(NVIDIA Geforce 7 serials) support
 • Integrated300MHzDACforexternaldesktopdisplay.
Expansion Slots
 • 1PCIExpressX16slot.
• 1PCIExpressX1slots(optional).
• 2 PCI bus master slots - ver. 2.3 compliant (optional).

7
Motherboard Layout
The following diagram shows the relative positions of the jumpers, connectors,
major components and memory banks on the motherboard.
NOTE :
1) Be sure to check the HDD cable orientation in order to match the colored
strip to the pin 1 end of the connector.
2) When you start up the system, please wait for 5 seconds after you power
on AC.
3) Adding a metal spaced plate to the back of the Socket 775 is not recom-
mended as this will short motherboard components and damage the system.
LGA775 Socket
FOXCONN
REM OVE

8
Technical Reference Booklet
PIN SIGNAL DESCRIPTION
1 VCC +5V/5VSB (optional)
2 -Data 0 Negative Data Channel 0
3 +Data0 Positive Data Channel 0
4 GND Ground
5 VCC +5V/5VSB (optional)
6 -Data 1 Negative Data Channel 1
7 +Data 1 Positive Data Channel 1
8 GND Ground
Rear Panel
The back panel provides the following connectors:
Mouse Connector
The motherboard provides a standard PS/2® mouse mini DIN connector
for attaching a PS/2® mouse. You can plug a PS/2® mouse directly into this
connector.
Keyboard Connector
The motherboard provides a standard PS/2® keyboard mini DIN connector for
attaching a PS/2® keyboard. You can plug a PS/2® keyboard directly into this
connector.
USB 2.0 Connector
The motherboard provides a UHCI (Universal Host Controller Interface)
Universal Serial Bus root for attaching USB devices such as keyboard, mouse
or other USB-compatible devices. You can plug the USB device directly into
the connector.
USB 2.0 Connector DescriptionUSB 2.0 Connector

9
Serial Port Connector: COM1
The Port is 16550A high speed communication ports that send/receive 16 bytes
FIFOs. You can attach a serial mouse or other serial devices directly to the
connectors.
Video Out Connector
The motherboard provides a Video out port to connect a 15-pin analog video
monitor.
RJ-45 LAN Jack (Optional)
The motherboard provides one standard RJ-45 jack for connection to Local
Area Network(LAN).You can connect a network cable to the LAN jack.
Parallel Port Connector:LPT1
The motherboard provides a 25-pin female centronic connector as LPT. A paral-
lel port is a standard printer port that supports Enhanced Parallel Port (EPP)
andExtendedCapabilitiesParallelPort(ECP)mode.
Audio Port Connector
Line_Out is a connector for Speakers or Headphones. Line In isusedforex-
ternal CD player, Tape player, or other audio devices. Mic In is a connector
for microphones. The ALC662 embeds an internal analog switch (by driver
software) to share LINE input with Surround output, and share MIC input with
CENTER/LFE output.
The ALC662 embeds the jack sensing function.When you plug an audio
device into the corresponding connector, the system will show you what you
pluged into the motherboard.

10
Technical Reference Booklet
Notice:
1.BesuretosavetheCMOSsettingwhenexittheCMOS.
2. If the CPU is frequency multiplier locked, no CPU speed change will be
seen even if the frequency multiplier setting in CMOS setup is changed.
Jumper Setting
This chapter explains how to congure the motherboard’s hardware. Before
using your computer, make sure all jumpers and DRAM modules are set
correctly. Refer to this chapter whenever in doubt.
1JP1
Ifyouwanttoclearthesystemconguration,usetheJP1(ClearCMOSJumper)
to clear data.
JP1-CMOS Clear
JCMOS1 Selection
1-2* Normal*
2-3 CMOS Clear
Close Open * = Default setting.
JP2 - P/S Port 5V Standby Power Selection
JP2 Selection
1-2* 5V standby power input*
2-3 5V power input
LGA775 Socket
FO XC O N N
1
JP2

11
CONNECTORS
The motherboard provides connectors to connect to the FDD, IDE HDD, SATA,
USB Ports and to CPU/PWR/System FAN etc.
Floppy Disk Drive Connector - CN3
Themotherboardprovidesastandardoppydiskdriveconnectorthatsupports
360K,720K,1.2M,1.44Mand2.88Moppydisktypes.
Hard Disk Connectors:CN1
The motherboard has a 32-bit Enhanced PCI IDE and Ultra DMA 66/100/133
controller that provides PIO mode 0~4, Bus Master, and Ultra DMA 66/100/133
function. You can connect up to two hard disk drives, CD-ROM, 120MB Floppy
(reserved for future BIOS) and other devices.
CN1
1
1
CN3
LGA775 Socket
FO XC O N N

12
Technical Reference Booklet
Serial ATA Hard Disk Connectors -
SATA1, SATA2, SATA3, SATA4
The motherboard has four SATA connectors. The motherboard provides optional
dual high-speed Serial ATA interface ports, SATA1, SATA2, SATA3, SATA4. Each
supports 2nd generation serial ATA data rates of 300MB/s. All connector types
arefullycompliantwithSerialATA2.0specications.EachSerialATAconnector
can connect to 1 hard disk device. Please refer to SATA Raid Setup for details
on software installation procedure.
PIN SIGNAL
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
SATA1, SATA2, SATA3, SATA4 - Pin Denition
LGA775 Socket
FO XC O N N
SATA2
SATA1 SATA3
SATA4

13
Fan Power Connectors - CPU FAN / SYS FAN1
The CPUFAN (processor fan), SYS FAN1 support system cool-ing fans using
+12V via a three-pin head connector. When connecting the wire to the connec-
tors, always take note that the red wire is the positive and should be connected
to the +12V, the black wire is Ground and should be connected to GND. If the
motherboard has a System Hardware Monitor chipset on-board, you must use
a specially designed fan with speed sensor to take advantage of the CPU fan
control.
CPU FAN
1
1
LGA775 Socket
FO XC O N N
SYS FAN1

14
Technical Reference Booklet
Front Panel Audio Header: FP- S1
This motherboard supports front panel microphone and speaker out ports.
If your computer case has these ports, connect them to FP-S1.
Note:
In order to utilize the front audio header, your chassis must have front audio con-
nector. Also please make sure the pin assignment on the cable is the same as the
pin assignment on the mainboard header. To nd out if the chassis you are buying
supports a front audio connector, please contract your dealer.
FP-S1
10
9
2
19
10
PIN Assignment
1 MIC2(L)
2 GND
3 MIC(R)
4 -ACZ-DET
5 Front Audio(R)
6 Reserved
7 FAVDIO - JD
8 Key (No pin)
9 Front Audio(L)
10 Reserved
FP - S1 Pin Denition
LGA775 Socket
FO XC O N N

15
USB Connectors - FP_U1/FP_U2
This motherboard has eight USB ports. Some computer cases have a special
module that mounts USB ports at the front of the case. If you have this kind of
case, use the auxiliary USB connectors FP_ U1/FP_U2 to connect the front
mounted ports to the motherboard.
PIN Assignment
1 VCC
2 VCC
3 USBP0-
4 USBP1-
5 USBP0+
6 USBP1+
7 GND
8 GND
9 KEY
10 GND
FP_U1/FP_U2 Connector
FP_U2
10
9
2
1
FP_U1
10
9
2
1
LGA775 Socket
FO XC O N N

16
Technical Reference Booklet
CN7 - Pin Denition
PIN Assignment
1 SPDIF-out
2 NC
3 +3.3V
4 +3.3V
5 NC
6 NC
7 GND
8 GND
7
SPDIF-out1
CN7
SPDIF-In/Out Header - CN7 (optional)
This header provides a SPDIF (Sony/Philips Digital Interface) output to digital
multimediadevicethroughberorcoaxialconnector.
LGA775 Socket
FOXCONN
REM OVE

17
CD-IN Connector - CD1 (optional)
The connector is for CD-ROM Drive.
1
PIN Assignment
1 CD-L
2 GND
3 GND
4 CD-R
CD1 - Pin Denition
CD1
LGA775 Socket
FO XC O N N
SPK
1
PIN Assignment
1 VCC
2 NC
3 NC
4 SPK-
SPK - Pin Denition

18
Technical Reference Booklet
Front Panel Header - FP1
The motherboard provides one front panel connector.
RESET GND HDD_LED- HDD_LED+
FP1
NC
PWR_SW
KEY
PW_LED+
7 9 5 3 1
6 8 10 2 4
GND
PW_LED-
LGA775 Socket
FO XC O N N

19
Slots
The motherboard provides one PCI-E X16 slot , one PCI-E X1 slots and two
32-bit PCI slots.
PCI-E X1 Slot
PCI Slots
PCI (Peripheral Component Interconnect) Slots
ThePCIslotsallowyoutoinsertexpansioncardstomeetyourneeds.When
addingorremovingexpansioncards,makesurethatyouunplugthepowersupply
rst.Readthedocumentationfortheexpansioncardandmakeanynecessary
hardwareorsoftwaresettingsfortheexpansioncard,suchasjumpers,switches
orBIOSconguration.
PCI-E X16 Slot
LGA775 Socket
FO XC O N N

20
Technical Reference Booklet
CPU Installation
Please follow the steps below to install the CPU.
1.Useindexngerandthumbto
move metal lever so it is separated
from the bottom steel shell grip
hook.
2.Use index finger to lift the top
steel
3.Useindexngerandthumbto
place the CPU onto the plastic body
(look for the gold arrow on the CPU.
The gold arrow should point away
from the lever pivot).