Zotac nForce 610i - ITX User manual

1
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with instructions
contained in this manual, may cause harmful interference to radio and television communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- REORIENT OR RELOCATE THE RECEIVING ANTENNA
- INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER
- CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM
THAT OF THE RECEIVER
- CONSULT THE DEALER OR AN EXPERIENCED AUDIO/TELEVISION TECHNICIAN
NOTE:
Connecting this device to peripheral devices that do not comply with Class B requirements, or
using an unshielded peripheral data cable, could also result in harmful interference to radio or
television reception.
The user is cautioned that any changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
To ensure that the use of this product does not contribute to interference, it is necessary to use
shielded I/O cables.
Copyright
This manual is copyrighted with all rights reserved. No portion of this manual may be copied or
reproduced by any means.
While every precaution has been taken in the preparation of this manual, no responsibility for
errors or omissions is assumed. Neither is any liability assumed for damages resulting from the
use of the information contained herein.
Trademarks
All brand names, logos and registered trademarks mentioned are property of their respective
owners.
Electronic Emission Notices
WARNING!

2
NForce 610i/630i-ITX series Motherboard
Table of Contents
Motherboard Specications ------------------------------------------------------------------- 5
Motherboard Layout------------------------------------------------------------------------------ 6
Hardware Installation ---------------------------------------------------------------------------- 8
Safety Instructions ----------------------------------------------------------------------------- 8
Preparing the Motherboard -------------------------------------------------------------------- 9
Installing the CPU------------------------------------------------------------------------------ 9
Installing the CPU Fan------------------------------------------------------------------------ 10
Installing Memory DIMMs -------------------------------------------------------------------- 10
Installing the Motherboard ------------------------------------------------------------------- 11
Installing the I/O Shield ----------------------------------------------------------------------- 11
Connecting Cables and Setting Switches ------------------------------------------------ 12
24-pin ATX Power (PW1)--------------------------------------------------------------------- 13
Hard Disk Connector-IDE-------------------------------------------------------------------- 13
4-pin ATX 12V Power (PW2) ---------------------------------------------------------------- 14
SPK Connector --------------------------------------------------------------------------------- 14
SPDIFOut Header - CN7 -------------------------------------------------------------------- 15
Serial Port Connector-COM ---------------------------------------------------------------- 15
Connecting Serial ATA Cables -------------------------------------------------------------- 16
Connecting Internal Headers---------------------------------------------------------------- 17
Front Panel Header---------------------------------------------------------------------------- 17
USB Headers------------------------------------------------------------------------------------ 18
Audio ---------------------------------------------------------------------------------------------- 19
Fan Connections ------------------------------------------------------------------------------- 20
Expansion Slots -------------------------------------------------------------------------------- 21
PCI Express x1 Slots-------------------------------------------------------------------------- 21
Jumper Settings -------------------------------------------------------------------------------- 22
Conguring the BIOS ---------------------------------------------------------------------------- 23
Enter BIOS Setup ------------------------------------------------------------------------------ 23
Main Menu ------------------------------------------------------------------------------------------- 24
Standard CMOS Features Menu-------------------------------------------------------------- 26
Date and Time ---------------------------------------------------------------------------------- 27
IDE Channel and SATA Channel ----------------------------------------------------------- 27
Drive A -------------------------------------------------------------------------------------------- 27

3
Table of Contents
Halt On-------------------------------------------------------------------------------------------- 27
Memory ------------------------------------------------------------------------------------------- 28
Advanced BIOS Features----------------------------------------------------------------------- 29
CPU Features--------------------------------------------------------------------------------------- 31
Hard Disk Boot Priority ------------------------------------------------------------------------- 32
Advanced Chipset Features ------------------------------------------------------------------- 35
Integrated Peripherals Menu ------------------------------------------------------------------ 36
Power Management Setup Menu ------------------------------------------------------------ 38
PnP/PCI Conguration -------------------------------------------------------------------------- 40
PC health status ----------------------------------------------------------------------------------- 42
Frequency/Voltage Control -------------------------------------------------------------------- 43
Load Optimized Defaults ----------------------------------------------------------------------- 44
Set Supervisor/User Password--------------------------------------------------------------- 45
Save & Exit Setup --------------------------------------------------------------------------------- 46
Exit Without Saving ------------------------------------------------------------------------------ 46
Installing Drivers and Software -------------------------------------------------------------- 47
Drivers Installing --------------------------------------------------------------------------------- 48
Flash Update Procedure ----------------------------------------------------------------------- 53
REALTEK HD AUDIO DRIVER SETUP ----------------------------------------------------- 54
Getting Started---------------------------------------------------------------------------------- 54
Sound Effect------------------------------------------------------------------------------------- 54
Environment Simulation ---------------------------------------------------------------------- 54
Equalizer Selection --------------------------------------------------------------------------- 55
Frequently Used Equalizer Setting -------------------------------------------------------- 55
Karaoke Mode ---------------------------------------------------------------------------------- 55
Mixer----------------------------------------------------------------------------------------------- 56
Playback control --------------------------------------------------------------------------- 56
Recording control-------------------------------------------------------------------------- 57
Audio I/O------------------------------------------------------------------------------------- 58
Speaker Conguration ------------------------------------------------------------------- 59
Global Connector Settings -------------------------------------------------------------- 60
S/PDIF --------------------------------------------------------------------------------------- 60
Speaker Calibration----------------------------------------------------------------------- 61
Microphone---------------------------------------------------------------------------------- 62
Noise Suppression ------------------------------------------------------------------------ 62

4
NForce 610i/630i-ITX series Motherboard
Beam Forming ----------------------------------------------------------------------------- 62
Acoustic Echo Cancellation------------------------------------------------------------- 62
Audio Demo--------------------------------------------------------------------------------- 63
Information --------------------------------------------------------------------------------- 63
SATA RAID User Manual ------------------------------------------------------------------------ 64
Setting up the BIOS --------------------------------------------------------------------------- 64
Entering the RAID BIOS Setup ------------------------------------------------------------- 66
Installing the RAID Drives-------------------------------------------------------------------- 69

5
Motherboard Specications
qChipset
NVIDIA MCP73 Series
qSize
Mini-ITX form factor of 170mm x 170mm
qMicroprocessor support
Intel LGA 775 Celeron® , Pentium® 4, Pentium® D, CoreTM 2 Series
qOperating systems:
Supports Windows XP 32bit/64bit and Windows Vista 32bit/64bit
qSystem Memory support
Supports DDRII533/667. Supports up to 4GBs DDRII memorys.
qUSB 2.0 Ports
v Supports hot plug and play
v Eight USB 2.0 ports (four rear panel ports, four from onboard USB headers)
v Supports wake-up from S1
v Supports USB 2.0 protocol up to 480 Mbps transmission rate
qOnboard Serial ATA II
v Independent DMA operation on two ports (optional).
vData transfer rates of 3Gb/s.
qOnboard LAN
vLAN interface built-in onboard
v Supports 10/100Mbps Ethernet
qOnboard Audio(optional)
v Azalia High-Denition audio
v Supports 6-channel
v Supports Jack-Sensing function
qGreen Function
v Supports ACPI (Advanced Conguration and Power Interface)
v RTC timer to power-on the system
v AC power failure recovery
qOnboard Graphics support
v Integrated 300MHz DAC for external desktop display.
qExpansion Slots
v One PCI Express x1 slot(optional)
Before You Begin

6
NForce 610i/630i-ITX series Motherboard
Motherboard Layout
Figure 1 shows the motherboard and Figures 2 shows the back panel connectors.
1.Front Panel Connector 11. Clear CMOS Jumper
2.SPK Connector 12. CPU Fan connector
3.SYS Fan connector 13. Backpanel connectors
4.Serial-ATA (SATA) Connectors 14. 4-pin ATX_12V power connector
5.Chipset 15. P/S port 5V standby selection Power
6.COM connector 16. CPU socket
7. PCI Express x1 slot(optional) 17. DDRII DIMM Sockets
8.USB Connectors 18. 24-pin ATX Power Connector
9.SPDIF-OUT Connector 19. IDE connector
10.FP_S1 FP Audio sound
Motherboard Layout
Figure 1. Board Layout
2
3
4
5
6
7
8
9
1 0
1 11 21 3
1 4
1 5
1 6
1 7
1 8 1 9

7
1. PS/2 Mouse Port
2. PS/2 Keyboard Port
3. VGA Connector
4. USB Connector
5. Port 2-Channel 4-Channel 6-Channe
Blue Line-In Rear Speaker Out Rear Speaker Out
Green Line-Out Front Speaker Out Front Speaker Out
Pink Mic In Mic In Center/Subwoofer
6. LAN Connector
Lan Port with LEDs to indicate status.
· Yellow/Light Up/Blink = 10 Mbps/Link/Activity
· Yellow and Green/Light Up/Blink = 100 Mbps/link/Activity
7. DVI Connector(optional for NForce630i-ITX)
Figure 2: Backpanel connectors
7

8
NForce 610i/630i-ITX series Motherboard
Hardware Installation
This section will guide you through the installation of the motherboard. The topics
covered in this section are:
q Preparing the motherboard
v Installing the CPU
v Installing the CPU fan
v Installing the memory
q Installing the motherboard
qConnecting cables and setting switches
Safety Instructions
To reduce the risk of re, electric shock, and injury, always follow basic safety precations.
Remember to remove power from your computer by disconnecting the AC main source
before removing or installing any equipment from/to the computer chassis.
Hardware Installation

9
Preparing the Motherboard
The motherboard shipped in the box does not contain a CPU and memory. You need
to purchase these to complete this installation.
Installing the CPU
Be very careful when handling the CPU. Make sure not to bend or break any pins on
the back. Hold the processor only by the edges and do not touch the bottom of the
processor.
Use the following procedure to install the CPU onto the motherboard.
1. Unhook the socket lever by pushing down and
away from the socket.
2. Lift the load plate. There is a protective socket
cover on the load plate to protect the socket
when there is no CPU installed.
3. Remove the protective socket cover from the
load plate.
4. Remove the processor from its protective cover,
making sure you hold it only by the edges.
It is a good idea to save the cover so that
whenever you remove the CPU, you have a
safe place to store it.
5. Align the notches in the processor with the
notches on the socket.
6. Lower the processor straight down into the
socket with out tilting or sliding it into the socket.
Note: Make sure the CPU is fully seated and
level in the socket.
7. Close the load plate over the CPU and press
down while you close and engage the socket
lever.

10
NForce 610i/630i-ITX series Motherboard
Installing the CPU Fan
There are many different fan types that can be used with this motherboard. Follow the
instruction that came with your fan assembly. Be sure that the fan orientation is correct
for your chassis type and your fan assembly.
Installing Memory DIMMs
Your new motherboard has two 1.8V 240-pin slots for DDR2 memory. These slots
support 256 Mb, 512 Mb, 1Gb and 2Gb DDR2 technologies. There must be at least
one memory bank populated to ensure normal operation. Use the following the rec-
ommendations for installing memory. (See Figure 1 on page 6 for the location of the
memory slots.)
q One DIMM: Install into slot 1 or 2. You can install the DIMM into any slot,
however, slot 1 is preferred.
q Two DIMMs: Install into slots 1 and 2. The idea is to not have the DIMMs in
adjacent slots.
Hardware Installation
DDRII-1
DDRII-2

11
Use the following procedure to install memory DIMMs into the slots on the
motherboard. Note that there is only one gap near the center of the DIMM slot. This
slot matches the slot on the memory DIMM to ensure the component is installed
properly.
1. Unlock a DIMM slot by pressing the module clips outward.
2. Align the memory module to the DIMM slot, and insert the module vertically into
the DIMM slot. The plastic clips at both sides of the DIMM slot automatically lock
the DIMM into the connector.
Installing the Motherboard
The sequence of installing the motherboard into the chassis depends on the chassis
you are using and if you are replacing an existing motherboard or working with an
empty chassis. Determine if it would be easier to make all the connections prior to this
step or to secure the motherboard and then make all the connections. It is normally
easier to secure the motherboard rst.
Use the following procedure to install the I/O shield and secure the motherboard into
the chassis.
Note: Be sure that the CPU fan assembly has enough clearance for the
chassis covers to lock into place and for the expansion cards. Also
make sure the CPU Fan assembly is aligned with the vents on the
covers.
Installing the I/O Shield
The motherboard kit comes with an I/O shield that is used to block radio frequency
transmissions, protects internal components from dust and foreign objects, and
promotes correct airow within the chassis.
Before installing the motherboard, install the I/O shield from the inside of the chassis.
Press the I/O shield into place and make sure it ts securely. If the I/O shield does
not t into the chassis, you would need to obtain the proper size from the chassis
supplier.

12
NForce 610i/630i-ITX series Motherboard
Connecting Cables and Setting Switches
This section takes you through all the connections and switch settings necessary on
the motherboard. This will include:
q Power Connections
v 24-pin ATX power (PW1)
v 4-pin ATX 12V power (PW2)
q Internal Headers
v Front panel
v USB Headers
v Audio
v Speaker
q Serial ATA II
q Chassis Fans
q Rear panel USB 2.0 Adapter
q Expansion slots
q CMOS jumper settings
See Figure 1 to locate the connectors and jumpers referenced in the following
procedure.
Hardware Installation

13
24-pin ATX Power (PW1)
PW1 is the main power supply connector located along the edge of the board next to
the DIMM slots. Make sure that the power supply cable and pins are properly aligned
with the connector on the motherboard. Firmly plug the power supply cable into the
connector and make sure it is secure.
Table 1. PW1 Pin Assignments
Connector Pin Signal Pin Signal
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PS_ON
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 PWROK 20 -5V
9 +5V_AUX 21 +5V
10 +12V 22 +5V
11 +12V 23 +5V
12 +3.3V 24 GND
112
13 24
Hard Disk Connector - IDE
The motherboard has a 32-bit Enhanced PCI IDE and Ultra DMA 66/100/133 control-
ler that provides PIO mode 0~4, Bus Master, and Ultra DMA 66/100/133 function. You
can connect up to two hard disk drives, CD-ROM, 120MB Floppy (reserved for future
BIOS) and other devices.
1

14
NForce 610i/630i-ITX series Motherboard
4-pin ATX 12V Power (PW2)
PW2, the 4-pin ATX 12V power connection, is used to provide power to the CPU. Align
the pins to the connector and press rmly until seated.
SPK
1
PIN Assignment
1 VCC
2 NC
3 NC
4 SPK-
SPK - Pin Denition
1
2
3
4
PIN Assignment
1 GND
2 GND
3 +12V
4 +12V
PW2 - Pin Denition
Hardware Installation
SPK Connector

15
SPDIF Out Header - CN7 (optional)
This header provides a SPDIF (Sony/Philips Digital Interface)output to digital multimedia
device through coaxial connector.
CN7 - Pin Denition
PIN Assignment
1 SPDIF-out
2 +3.3V
3 NC
4 GND
SPDIF
1
Serial Port Connector - COM
1
2
9
10
COM
COM - Pin Denition
PIN Assignment
1 DCD
2 RXD
3 TXD
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
9 RI
10 NC

16
NForce 610i/630i-ITX series Motherboard
PIN SIGNAL
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
SATA-1/SATA-2- Pin Denition
Connecting Serial ATA Cables(SATA-1~SATA-2 Optional)
The Serial ATA II connector is used to connect the Serial ATA II device to the
motherboard. These connectors support the thin Serial ATA II cables for primary
storage devices. The current Serial ATA II interface allows up to 3Gb/s data transfer
rate.
There are two serial ATA connectors on the motherboard that support AHCI and RAID
congurations.
SATA-1
SATA-2
1
1
Hardware Installation

17
Connecting Internal Headers
Front Panel Header
The front panel header on this motherboard is one connector used
to connect the following four cables (see Table 2 for pin denitions):
q PWRLED
Attach the front panel power LED cable to these two pins of the connector. The
Power LED indicates the system’s status.
Note: Some chassis do not have all four cables. Be sure to match the name on
the connectors to the corresponding pins.
q PWR SW
Attach the power button cable from the case to these two pins. Pressing the
power button on the front panel turns the system on and off rather than using the
power supply button.
q HDD LED
Attach the hard disk drive indicator LED cable to these two pins. The HDD
indicator LED indicates the activity status of the hard disks.
q RST SW
Attach the Reset switch cable from the front panel of the case to these two pins.
The system restarts when the RESET switch is pressed.
RESET GND HDD_LED-
HDD_LED+
FP1
NC
PWR_SW
KEY
PW_LED+
7
9
5 3
1
6 8 10 2 4
GND
PW_LED-
Front Panel Header
Pin Denition

18
NForce 610i/630i-ITX series Motherboard
PIN Assignment
1 VCC
2 VCC
3 USBP0-
4 USBP1-
5 USBP0+
6 USBP1+
7 GND
8 GND
9 KEY
10 OC#
FP-U1/FP-U2 - Pin Denition
1
2
9
10
USB Headers
This motherboard contains four USB 2.0 ports that are exposed on the rear panel of
the chassis(Figure 2). The motherboard also contains two 10-pin internal header con-
nectors onboard.
1. Secure the bracket to either the front or rear panel of your chassis (not all chassis
are equipped with the front panel option).
Hardware Installation

19
1
2
9
10
Audio
The audio connector supports HD audio standard and provides two kinds of audio
output choices: the Front Audio, the Rear Audio. The front Audio supports re-tasking
function.
Note:
In order to utilize the front audio header, your chassis must have front audio connector.
Also please make sure the pin assignment on the cable is the same as the pin assignment
on the mainboard header. To nd out if the chassis you are buying supports a front audio
connector, please contract your dealer.
PIN Assignment
1 MIC2(L)
2 GND
3 MIC(R)
4 -ACZ-DET
5 Front Audio(R)
6 Reserved
7 FAVDIO - JD
8 Key (No pin)
9 Front Audio(L)
10 Reserved
FP - S1 Pin Denition