JETWAY MM10-H6100 User manual

TECHNICAL MANUAL
Of
Of Intel H610/Q670E Express Chipset
Based Micro-ATX M/B
No. G03-MM10-F
Rev: 1.0
Release date: November 29, 2022
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are subject
to change at any time without notice, and should not be construed as a commitment by manufacturer.

ii
ENVIRONMENTAL SAFETY INSTRUCTION...........................................................................iii
ENVIRONMENTAL PROTECTION ANNOUCEMENT..............................................................iii
USER’S NOTICE .......................................................................................................................iv
MANUAL REVISION INFORMATION.......................................................................................iv
ITEM CHECKLIST .....................................................................................................................iv
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 SPECIFICATION.........................................................................................................1
1-2 LAYOUT DIAGRAM....................................................................................................3
CHAPTER 2 HARDWARE INSTALLATION
2-1 JUMPER SETTING .....................................................................................................8
2-2 CONNECTORS AND HEADERS................................................................................10
2-2-1 REAR I/O BACK PANEL CONNECTORS....................................................10
2-2-2 MOTHERBOARD INTERNAL CONNECTORS............................................11
2-2-3 HEADER PIN DEFINITION ...........................................................................15
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERNING SETUP...................................................................................................20
3-2 BIOS MENU SCREEN ................................................................................................21
3-3 FUNCTION KEYS .......................................................................................................21
3-4 GETTING HELP ..........................................................................................................22
3-5 MENU BARS...............................................................................................................22
3-6 MAIN MENU................................................................................................................22
3-7 ADVANCED MENU.....................................................................................................23
3-8 CHIPSET MENU..........................................................................................................34
3-9 SECURITY MENU.......................................................................................................36
3-10 BOOT MENU...............................................................................................................38
3-11 SAVE & EXIT MENU...................................................................................................38
TABLE OF CONTENT

iii
Environmental Safety Instruction
⚫Avoid the dusty, humidity and temperature extremes. Do not place the product in
any area where it may become wet.
⚫0 to 40 centigrade is the suitable temperature. (The figure comes from the request
of the main chipset)
⚫Generally speaking, dramatic changes in temperature may lead to contact
malfunction and crackles due to constant thermal expansion and contraction from
the welding spots’ that connect components and PCB. Computer should go
through an adaptive phase before it boots when it is moved from a cold
environment to a warmer one to avoid condensation phenomenon. These water
drops attached on PCB or the surface of the components can bring about
phenomena as minor as computer instability resulted from corrosion and oxidation
from components and PCB or as major as short circuit that can burn the
components. Suggest starting the computer until the temperature goes up.
⚫The increasing temperature of the capacitor may decrease the life of computer.
Using the close case may decrease the life of other device because the higher
temperature in the inner of the case.
⚫Attention to the heat sink when you over-clocking. The higher temperature may
decrease the life of the device and burned the capacitor.
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.

iv
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIESANDWE
DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
1.0 First Edition November 29, 2022
Item Checklist
Motherboard
Cable(s)
I/O Back panel shield

1
Chapter 1
Introduction of the Motherboard
1-1 Specification
Spec
Description
Design
⚫Micro ATX form factor; PCB size: 24.4 x24.4 cm
Chipset
⚫MM10-H6100/6102 series: Intel H610 Chipset
⚫MM10-Q6700/6702 series: Intel Q670E Chipset
CPU Socket
⚫IntelLGA 1700 Socket supports 12th/13th processors (Max.
65W TDP)
*Note:for detailed CPU support information please visit our website
Memory Slots
⚫MM10-H6100/6102 series: 2* Long DIMM DDR5 slot for 2* DDR5
up to 4800MHz RAM Module
⚫MM10-Q6700/6702 series: 4* Long DIMM DDR5 slot for 4* DDR5
up to 4800MHz RAM Module
⚫Support dual channel function
Maximum capacity: up to 128GB (MM10-H6100/6102 series
support up to 64GB)
Maximum frequency: 4800 MHz (depends on CPU support)
Expansion
Slots
⚫1* PCI-Express 5.0 x16 slot (PCIE1)
⚫1* PCI-Express 4.0 x4 slot (PCIE2 for MM10-Q6700/6702 Series
only)
⚫2* PCI-Express 3.0 x4 slot (PCIE3/4).
⚫1* M.2 E-key 2230 USB2.0 interface support CNVi (M2E1 for
MM10-H6100/6102 series)
⚫1* M.2 E-key 2230 USB2.0/PCIe 3.0x1 interface support CNVi
(M2E1 for MM10-Q6700/6702 series)
Storage
⚫MM10-H6100/6102 series:
3* SATAIII 6Gb/s port s (SATA2 support powered SATA DOM)
1* M.2 M-key 2242/2260/2280/22110 SATA slot (M2M1)
⚫MM10-Q6700/6702 series:
3*SATAIII 6Gb/s port support RAID 0/1/5 (SATA2 support
powered SATA DOM)
1* M.2 M-key 2242/2260/2280/22110 SATA/PCIe 4.0x4 interface
supports NVMe (M2M1)
*Note: Support RAID 0/1 by using SATA3 and SATA4; RAID 0/1/5 by
using SATA3, SATA4, and SATA2; RAID 0/1/5/10 by using SATA3,
SATA4, SATA2, M.2 M-key with SATA interface.
LAN Chips
⚫MM10-H6100/6102 series: 1* Intel i219V GbE & 1* Realtek
RTL8153 GbE
⚫MM10-Q6700/6702 series: 1* Intel i219LM GbE, 1* Realtek
RTL8153 GbE, 1* Intel i225V 2.5GbE
*Note: 2500Mbps high-speed transmission rate is only supported over
CAT 5e UTP cable.
BIOS
⚫AMI 256M Bit AMI Flash ROM

2
Multi I/O
Rear Panel I/O:
⚫2* HDMI
⚫1* DP
⚫2* 1GbE RJ-45 LAN port
⚫1* 2.5GbE RJ-45 LAN port (MM10-Q6700/6702 Series only)
⚫1* COM (RS232/422/485)
⚫1* 3-jack audio connector (Line-in, Line-out, MIC)
⚫MM10-H6100/6102 Series: 2* USB 3.2 (Gen.2) + 4* USB 2.0
⚫MM10-Q6700/6702 Series: 6* USB 3.2 (Gen.2)
Internal I/O Connectors & Headers:
⚫1* 24-pin main power connector
⚫1* 8-pin 12V power connector
⚫1* CPUFAN connector & 2* SYSFAN connectors
⚫1* Front panel header
⚫1* 10-Pin USB 3.2 (Gen.1) header
⚫1* 4-Pin USB 2.0 header
⚫2* Vertical USB 2.0 headers
⚫MM10-H6100/6102 Series: 2* 9-Pin USB 2.0 headers for 4* USB
2.0 ports
⚫MM10-Q6700/6702 Series: 4* 9-Pin USB 2.0 headers for 8* USB
2.0 ports
⚫5* RS232 COM port headers
⚫1* 15-Pin VGA port header
⚫1* 8-bit GPIO header
⚫1* PS/2 Keyboard & Mouse header
⚫1* 5-Pin SMBUS header
TPM 2.0 Function
⚫Optional for MM10-H6102 & MM10-Q6702 Series

3
1-2 Layout Diagram
Rear IO Diagram
MM10-H6100/6102 Series:
MM10-Q6700/6702 Series:
*Note: COM1 support RS232/422/485 function for both MM10-H6100/6102 Series
and MM10-Q6700/6702 Series.
RJ-45 LAN Ports
(1GbE)
RJ-45 LAN Ports
(2.5GbE)
USB 3.2 (Gen.2)
Ports
RJ-45 LAN Ports
(1GbE)
DisplayPort
COM1
Serial Port
HDMI Ports
USB 2.0
Ports
Audio
Connector
Audio
Connector
USB 3.2 (Gen.2)
Ports
USB 2.0
Ports
HDMI Ports
COM1
Serial Port
DisplayPort

4
Motherboard Internal Diagram
MM10-H6100/6102 Series:
VGA Header
*Rear IO
Connector
(Refer to Page-2)
RS 232 Serial Port Headers
(COM2/3/4/5/6)
ATX 12V Power
Connector
CPU FAN
Connector
SYSFAN1
PCIE1: PCIe 5.0 x16 slot
PCIE3: PCIe 3.0 x4 slot
PCIE4: PCIe 3.0 x4 slot
M.2 E-Key Slot
Type-2230 (USB2.0)
M.2 M-Key Slot
Type-2242/2260/2280/22110 (SATA)
Intel H610 Chipset
ATX Power
Connector
SATAIII DOM Port
(SATA2)
SATAIII Ports
(SATA3/4)
USB 3.2 (Gen.1) Header
(USB3)
Internal Vertical
USB2.0 Connector
(USB2/USB1)
SMBUS Header
Front Panel
Audio Header
HDMI_SPDIF
Header
GPIO Header
USB2.0 Header
(FP_USB6)
USB2.0 Headers
(FP_USB4/5)
DDR5 UDIMM Slots x2
Front Panel Header
PS/2 KB & MS Header
SYSFAN2

5
MM10-Q6700/6702 Series:
*Rear IO
Connector
(Refer to Page-2)
RS 232 Serial Port Headers
(COM2/3/4/5/6)
Front Panel
Audio Header
HDMI_SPDIF
Header
GPIO Header
USB2.0 Headers
(FP_USB2/3/4/5)
PS/2 KB & MS Header
Front Panel Header
SYSFAN2
USB2.0 Header
(FP_USB6)
SATAIII Ports
(SATA3/4)
Internal Vertical
USB2.0 Connector
(USB2/USB1)
SMBUS Header
SATAIII DOM Port
(SATA2)
ATX Power
Connector
USB 3.2 (Gen.1) Header
(USB3)
SYSFAN1
DDR5 UDIMM Slots x4
CPU FAN
Connector
ATX 12V Power
Connector
VGA Header
PCIE1: PCIe 5.0 x16 slot
PCIE2: PCIe 4.0 x4 slot
M.2 E-Key Slot
Type-2230 (USB2.0/PCIe 4.0 x1))
PCIE3: PCIe 3.0 x4 slot
PCIE3: PCIe 3.0 x4 slot
M.2 M-Key Slot
Type-2242/2260/2280/22110
(SATA/PCIe 4.0x4)

6
Motherboard Jumper Position:
*Note:The diagrams in the manual are mostly taken from MM10-Q6700/6702 series unless otherwise
stated.
Jumper
Jumper
Name
Description
Pitch
JBAT1
Clear CMOS RAM Settings
3-pin Block
2.0mm
JAT_ATX
ATX/AT Mode Select
3-pin Block
2.54mm
COPEN
Case Open Message Display Detect
2-pin Block
2.54mm
JP1
ME Features Select
2-pin Block
2.0mm
JP2
COM1 Port Pin9 Function Select
4-pin Block
2.0mm
JP3
COM2 Port Pin9 Function Select
4-pin Block
2.0mm
JP4
GPIO/80 Port Select
2-pin Block
2.0mm
JP2
JP3
JBAT1
JAT_ATX
COPEN
JP1
JP4

7
Connectors
Connector
Name
COM1
Serial Port X1
DP
Display 1.4a Port X1
(Max Resolution: 4096x2304@60Hz)
HDMI1-2
HDMI 2.0b Port X2
(Max Resolution: 4096x2160@60Hz)
UL1
Top: 1GbE RJ-45 Port X1
Middle & Bottom: USB 3.2 (Gen.2) Port X2
UL2
Top: 1GbE RJ-45 LAN Port X1
Middle & Bottom: USB 2.0 Port X2 (MM10-H6100/6102)
USB 3.2 (Gen.2) Port X2
(MM10-Q6700/6702)
UL3
MM10-H6100/6102: USB 2.0 Port X2
MM10-Q6700/6702:
Top: 2.5GbE RJ-45 Port X1
Middle & Bottom: USB 3.2 (Gen.2) X2
ATXPWR1
ATX Type Main Power Connector
ATX12V1
ATX 12V Power Connector
CPUFAN1
CPU FAN Connector
SYSFAN1/2
System FAN Connector X6
SATA2
SATAIII Connector X1
SATA_RA3
SATAIII Connector X2
Headers
Header
Name
Description
Pitch
FP
(Front Panel Header)
PWR LED/ HD LED/ Power
Button /Reset
10-pin Block
2.54mm
MM10-Q6700/6702 Series
only :
FP_USB2/FP_USB3
USB 2.0 Port Header X2
9-pin Block
2.0mm
FP_USB4/FP_USB5
USB 2.0 Port Header X2
9-pin Block
2.0mm
FP_USB6
USB 2.0 Port Header X1
4-pin Block
2.0mm
USB3
USB 3.2 (Gen.1) Port Header
10-pin Block
2.0mm
COM2/3/4/5/6
RS232 Serial Port Header X5
9-pin Block
2.54mm
GPIO
GPIO Header
10-pin Block
2.0mm
PS2KBMS
PS/2 Keyboards & Mouse Header
6-pin Block
2.54mm
SMBUS1
SMBUS Header
5-pin Block
2.0mm

8
Chapter 2
Hardware Installation
2-1 Jumper Setting
JBAT1 (3-pin): Clear CMOS Pitch=2.0mm
3
1
3
1
1-2 Closed: Normal (Default);
2-3 Closed: Clear CMOS Settings.
JAT_ATX (3-pin): ATX Mode/AT Mode Select Pitch=2.54mm
3
1
3
1
1-2 Closed: ATX Mode Selected;
2-3 Closed: AT Mode Selected.
*ATX Mode Selected: Press power button to power on after power input ready;
AT Mode Selected: Directly power on as power input ready.
COPEN (2-pin): Case Open Message Display Function Pitch=2.54mm
Pin1
GND
CASE OPEN
JBAT1
JAT_ATX
COPEN

9
Pin 1-2 Short:When Case open function pin short to GND, the Case open function was
detected. When Used, needs to enter BIOS and enable ‘Case Open Detect’ function. In this
case if your case is removed, next time when you restart your computer, a message will be
displayed on screen to inform you of this.
JP2 (4-piin): COM1 Header Pin9 Select Pitch=2.0mm
JP2
→
COM1 Header Pin-9 Select
4-6 Closed:
RI= +12V
3-4 Closed:
RI= +5V
2-4 Closed: RI=
RS232
6
4
2
3
1
5
1
3
5
2
4
6
1
3
5
2
4
6
*Note: Maximum current limit is 500mA while using 5V or 12V.
JP3 (4-pin): COM2 Header Pin9 Select Pitch=2.0mm
4-6 Closed:
RI= +12V
3-4 Closed:
RI= +5V
2-4 Closed:
RI=RS232
1
3
5
2
4
6
6
4
2
1
3
5
6
4
2
1
3
5
JP3
→
COM2 Header Pin-9 Select
*Note: Maximum current limit is 500mA while using 5V or 12V.
JP1 (2-pin): ME Features Select Pitch=2.0mm
Pin1
Pin1
1-2 Closed: Disable ME Features.
1-2 Open: Enable ME Features(Default);
COM2
JP3
JP2
COM1
JP1

10
JP4 (2-pin): GPIO/80 PORT MODE Select Pitch2.0mm
Pin1
Pin1
1-2 Closed: GPIO= GPIO Port (Default).
.
1-2 Open: GPIO= 80 Port;
2-2 Connector and Headers
2-2-1 Rear I/O Back Panel Connectors
*Refer to Page-2 Rear IO Diagram
Icon
Name
Function
Serial Port
Mainly for user to connect external MODEM or other
devices that supports Serial Communications Interface.
HDMI 2.0 Port
To connect display device that support HDMI specification.
Display 1.4 Port
To the system to corresponding display device with
compatible display port cable.
RJ-45 LAN Port
This connector is standard RJ-45 LAN jack for Network
connection. These two RJ-45 LAN port from UL1 and UL2
support 1.0GbE transfer rate.
RJ-45 LAN Port
This connector is standard RJ-45 LAN jack for Network
connection. These two RJ-45 LAN port from UL3 support
2.5GbE transfer rate. (MM10-Q6700/6702 only)
(*Note: 2.5Gbps is only supported with CAT5e UTP
cable).
USB 3.2 (Gen.2)
Port
To connect USB keyboard, mouse or other devices
compatible with USB 3.2(Gen.2) specification. Ports
support up to 10Gbps data transfer rate.
USB 2.0 Port
To connect USB keyboard, mouse or other devices
compatible with USB 2.0 specification. Ports support up to
480Mbps data transfer rate.
JP4

11
Audio Connectors
BLUE: Line-in Connector
GREEN: Line-out Connector
PINK: MIC Connector
COM1 (9-pin Block): Serial Port
The pin assignment for RS232/422/485 is listed as follows:
1
2
3
4
5
6
7
8
9
RS232 DCD#
RS232 SIN
RS232 SOUT
RS232 DTR#
GND
RS232 RI#
RS232 CTS#
RS232 RTS#
RS232 DSR#
RS232 Mode
(MM21-Q4700/Q4702 Series
& MM21-W4800/W4802 Series)
RS422 Mode
(MM21-Q4700/Q4702 Series)
RS485 Mode
(MM21-Q4700/Q4702 Series)
Pin1
GND
RS422 RX(B)
RS422 RX(A)
RS422 TX(A)
RS422 TX(B)
Pin1
GND
RS485 D+(A)
RS485 D-(B)
Pin1
*Note: COM1 support RS232/422/485 function.
2-2-2 Motherboard Internal Connectors
(1) ATXPWR1 (24-pin block): Main Power Connector
ATX Power Supply connector: This is a new defined 24-pins connector that usually
comes with ATX case. The ATX Power Supply allows using soft power on
momentary switch that connect from the front panel switch to 2-pins Power On
jumper pole on the motherboard. When the power switch on the back of the ATX
power supply turned on, the full power will not come into the system board until the
front panel switch is momentarily pressed. Press this switch again will turn off the
power to the system board.
** We recommend that you use an ATX 12V Specification 2.0-compliant power
supply unit (PSU) with a minimum of 350W power rating. This type has 24-pin and
4-pin power plugs.
** If you intend to use a PSU with 20-pin and 4-pin power plugs, make sure that the
20-pin power plug can provide at least 15A on +12V and the power supply unit has a
minimum power rating of 350W. The system may become unstable or may not boot
up if the power is inadequate.
** If you are using a 20-pin power plug, please refer to Figure1 for power supply
connection. Power plug form power supply and power connectors from motherboard
both adopt key design to avoid mistake installation. You can insert the power plug

12
into the connector with ease only in the right direction. If the direction is wrong it is
hard to fit in and if you make the connection by force if is possible.
Figure1：20-pin power plug Figure 2：24-pin power plug
(2) ATX12V1(8-pin): 12V Power Connector
This is a new defined 8-pin connector that usually comes with ATX Power Supply.
The ATX Power Supply which fully supports AMD AM3 processor must including
this connector for support extra 12V voltage to maintain system power
consumption. Without this connector might cause system unstable because the
power supply can not provide sufficient current for system.
ATXPWR1
ATX12V1

13
(3) CPUFAN1 (4-pin): CPU Fan Connector
Pin1
GND
+12V Fan Power
Fan Speed
Control
*Note: Maximum current limit is 0.5A while using 5V working voltage
(4) SYSFAN1/2 (3-pin): System Fan 1 & 2 Connectors
Pin1
GND
+12V Fan Power
Fan Speed
*Note: Maximum current limit is 0.5A while using 5V working voltage
(5) SATA2/3/4 (7-pin): SATAIII Port Connectors
These are high-speed SATAIII ports that support 6GB/s transfer rate.
Pin No.
Definition
1
GND
2
TXP
3
TXN
4
GND
5
RXN
6
RXP
7
GND
CPUFAN1
SYSFAN1
SYSFAN2
SATA2
SATA3/4
44

14
(6) Dual Channel Memory Installation
Notice!
⚫For dual channel installation, you need to install the same brand, speed, size and
type memory module. *Please follow the instruction above to prioritize
DIMM2 slot when installing one or two memory modules.
⚫It is unable to activate dual channel feature if you install one or three memory
modules, or you install DIMM1 & DIMM4 / DIMM2 & DIMM3. Slot order can be
from left-to-right or right-to-left, and it must be installed in pairs.
⚫If you install memory modules in wrong direction, it will damage the motherboard
and memory module.
2-2-3 Header Pin Definition
(1) FP (10-pin): Front Panel Header Pitch=2.54mm
Configuration
DIMM1
DIMM2
DIMM3
DIMM4
1
--
install
--
--
2
--
install
--
install
3
install
install
install
install
DIMM 4
DIMM 2
DIMM 3
DIMM 1

15
GND
RSTSW
Pin
1
2
HDDLED+
HDDLED-
VCC5V
PWRLED+
PWRLED-
PWRBTN
GND
*Note: Maximum current limit is 1A while using 5V working voltage
(2) USB3 (10-pin): USB 3.0 Port Header Pitch=2.0mm
*Note: Maximum current limit is 1.5A while using 5V working voltage
(3) FP_USB2~FP_USB5 (9-pin): USB 2.0 Port Header Pitch=2.0mm
Pin1
VCC
-DATA
+DATA
GND
VCC
+DATA
-DATA
GND
NC
*Note: Maximum current limit is 1.5A while using 5V working voltage.
MM10-H6100/6102 only has FP_USB4/5.
FP
USB3
FP_USB2
FP_USB3
FP_USB5
FP_USB4

16
(4) FP_USB6 (4-pin): USB 2.0 Port Header Pitch=2.0mm
Pin1
DATA-
VCC
DATA+
GND
*Note: Maximum current limit is 1.5A while using 5V working voltage
(5) FP_Audio (10-pin): Front Panel Audio Header Pitch=2.0mm
Pin1
2
MIC-L
LINEOUT-L
MIC-R
LINEOUT-R
SENSE
GND
LINEOUT-JD
MIC-JD
AUDIO_JD
(6) COM7-10 (35-pin): Reserved Serial Port (support RS232) Pitch=2.0mm
*Note: COM7-10 ports are optional and by request only
FP_AUDIO
PinA1
PinB1
COM7-10
FP_USB6