Zte MC7010 User manual

MC7010
Quick Start Guide
EN 1
FI 25
SV 52
NO 79
DK 106


Scan this QR code to download the Install Helper
application.

1
LEGAL INFORMATION
Copyright © 2021 ZTE CORPORATION
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or utilized in
any form or by any means, electronic or mechanical, including photocopying and
microlm, without the prior written permission of ZTE Corporation.
This document is published by ZTE Corporation. We reserve the right to make
modications on print errors or update.
Version No.: R1.0
Unpacking and Preparations
Before installing the device, make sure that all items listed in the packing list are
present. If something is missing or damaged, please contact ZTE technical support.
Packing List
The MC7010 ODU CPE The Quick Start Guide 1 Cover plate set(POE
adapter):
Anti-theft screw * 2, Screw
anti-theft key * 1

2
Mounting Kit: Metal
bracket, Backplane,
Metal clamp, M6
expansion bolts & M6
expansion spigots*4, M3
crosshead screws*5
1 POE adapter and AC
Power cord
1 long network cable(for
connecting the device
and POE adapter), 1
short network cable for
connecting the POE
adapter and PC/Router),
RJ45 socket*2
Prepare the following accessories (not included):
• Crosshead screwdriver
• Flat head screwdriver
• Hammer drill
• Marker pens
Installation Precautions
• Do not install the device in the following directions:
Do not install the device
with the interface side
facing upwards.
Do not install the device
horizontally.
Do not install the device
tilted.
WARNING!
The device must be installed downwards and vertically. It is not recommended
to install the device in other directions (including but not limited to the above

3
scenarios). ZTE is not liable for any problem caused by the installation in other
incorrect directions.
• Do not install the device at a high position (lightning area).
• The device must be placed in a well-ventilated environment for use. If possible,
install the device in a place with less direct sunlight, for example, in the shade.
The device must not be installed at the outlet of the exhaust pipe, or installed
in a place where water passes through, for example, a rain shed.
• The device shall be installed in the position of the site survey design drawings
and within the protection range of 45° of the lightning rod. In high mountains
and areas with heavy lightning (the number of thunderstorm days per year
exceeds 180), ensure that the device is within the protection range of 30°of the
lightning rod.
• When the device is mounted on the wall, it should better be more than 1 m
away from the grounding cable of the lightning rod and more than 20 cm away
from the lightning protection zone.
• When installing the device against a pole, do not install a lightning rod on the
pole. It is recommended that an independent lightning rod be installed near
the pole. If a lightning rod is installed on the pole, it is recommended that the
lightning rod be led out and grounded directly.
• The mounting pole must be rm, cannot be shaken and must meet the wind-
resistant requirements (not less than level-10 wind speed).
• The mounting pole should be vertical, and the vertical error should be less
than ±2°.
Installation Modes
You can install the device in either of the following ways:
Install the device on a wall. Install the device against a pole.

4
Requirements of Installation Space and Medium
• Installation space requirements
• Installation medium requirements
Mounting pole

5
Recommended Installation Locations

6
Installing the nano-SIM Card
Insert the nano-SIM card to the SIM card slot as shown.
WARNING!
Your device does not support (U) SIM cards, micro-SIM cards or any other non-
standard SIM cards. To avoid damage to the device, do not use those cards or any
card holders.
Installing the Network Cable
1. Connect the RJ45 to the network port on the MC7010 while the two screws are
also inserted into the holes at the bottom of the device.

7
2. Push the cover plate upwards until it is secured, and use a screw anti-theft
removal wrench to install the cover plate on the device.
NOTES:
If the mains cable is more than 0.8m visible outside the house after installation, it
must be attached to a wall or rod to avoid damage.

8
Using Install Helper Application to Detect
Position
Before installing the MC7010, you can install the Install Helper application on your
mobile phone and connect to the device to detect the signal strength and help you
detect and locate the installation location.
NOTE:
View the label on this guide to get the link or QR code to download the Install
Helper application.
Powering on the MC7010
1. Connect the CAT5E network cable which is from the MC7010 to the network
port (RJ45-2) on the POE adapter.
2. Connect the power connector on the POE adapter to the socket.
Connecting to the MC7010
Before connecting to the device, make sure that you have installed the Install
Helper application and turn on Bluetooth® of your phone.
1. Open the app list and touch Install Helper.
2. Touch CONNECT TO DEVICE and select MC7010. The Bluetooth of the
device will turn on automatically, and your phone automatically scans for and
displays the IDs of all available Bluetooth devices in range.
3. Touch the device you want to pair with.
4. Touch PAIR & CONNECT > PAIR to accept the connection.
5. Enter the password and touch OK to manage the device.
NOTE:
View the label on this guide to get the default password.
Detecting and Adjusting Installation Position
1. Move the device around the mounting wall/pole or try dierent positions and
touch DETECT POSITION.
2. Follow the on-screen instructions to attach the device to your target position,
and slowly move it until it provides feedback.

9
NOTE:
The device does not support elevation angle adjustment. It only supports
horizontal 180° adjustment.
3. The signal strength at the current position is displayed (Perfect, Great, Good,
Poor and Terrible). You can touch view details to view the network details.
When the device signal is detected, your phone automatically beeps. The
louder the sound and the stronger the vibration, the better the signal strength.
NOTE:
Touch FINISH to end the detection and select whether to save the current
position if needed.
4. Continue the detection until the desired position is detected, and save or
continue to adjust the position as prompted.
Powering o the MC7010
After the installation position is determined, disconnect the POE adapter from the
device.
Installing Your Device
Installing the Device on a Wall
1. Mark the positions for drilling holes on the wall.

10
2. Firstly, use a 6mm percussion drill to drill holes at the marked positions, and
install four M6 expansion spigots. Secondly, use four M6 expansion bolts to x
the bracket to the wall.
CAUTION:
The screw hole of the bracket faces upwards. Do not install the bracket upside
down. Otherwise, the screw cannot be installed later.
3. Use four M3 crosshead screws to install the backplane on the device.

11
4. Firstly, fasten the backplane to the installed bracket through the upper and
lower slots, and align the hole on the backplane with the hole on the bracket.
Secondly, use one M3 crosshead screw to install the MC7010 on the bracket.
Installing the Device against a Pole
1. Use a screwdriver to loosen the clamp and release the buckle.

12
2. Pass the clamp through the U-shape groove on the bracket to install the
bracket against the pole.
CAUTION:
The screw hole of the bracket faces upwards. Do not install the bracket upside
down. Otherwise, the screw cannot be installed later.
3. Adjust the clamp to the proper tightening position, press the buckle and use a
screwdriver to lock the clamp to x the bracket.

13
4. Use four M3 crosshead screws to install the backplane on the device.
5. Firstly, fasten the backplane to the installed bracket through the upper and
lower slots, and align the hole on the backplane with the hole on the bracket.
Secondly, use one M3 crosshead screw to install the MC7010 on the bracket.
NOTE:
Before installing the device on the bracket, you can move the device
horizontally and slowly on the pole to further adjust the position if needed.

14
Connecting the POE Adapter
1. Connect the CAT5E network cable which is from the MC7010 to the network
port (RJ45-2) on the POE adapter.
2. Connect the PC network port (RJ45-1) on the POE adapter to your PC/IDU
(router) with the RJ-45 network cable.
Installation Check
Device Installation:
• The MC7010 is installed rmly.
• The network cables are installed rmly.
• The cover plate on the device is installed.
• The nano-SIM card is installed.
• The network interface on the POE adapter is installed correctly.
Cables Installation:
• Verify that all cables are connected properly, cable connectors are secure.
• Cables should be laid in a clear and straight manner without crossing each
other. There is no obvious curve or slant. Cables do not hang in the air or cross
each other.

15
System Power-On
Powering on the device
Connect the power connector on the POE adapter to the socket. The POE adapter
starts to supply power to the MC7010. When the indicator of the POE adapter and
POWER LED of the device turns green, the MC7010 is correctly powered.
Preliminary Device Acceptance
1. Check indicator status.
2. Connect the device to a PC and log in to the conguration page to view the
device status.
LED Behavior
When setting up the MC7010, the LED will have the following behavior.
Indicator Status Description
POWER
④
On Power is on and external power supply is working
normally.
O Power is o.
NETWORK
②
Red blinking The device is in error status:
• The device is not registered to the mobile
network.
• There is no nano-SIM card inserted.
• There is no network service available.
Green on The device is registered or connected to the 5G
network and data is being transferred.
Green blinking The device is connected or connected to the
3G/4G LTE network and data is being transferred.
LAN
③
Green on The LAN port is connected.
Green blinking Data is being transferred.
O The LAN port is not connected.

16
Indicator Status Description
SIGNAL
①
On Three
LEDs on
5G/4G LTE The signal strength is Perfect/
Great (RSPR≥-95dB).
3G The signal strength is Perfect/
Great (RSPR≥-93dB).
Two LEDs
on 5G/4G LTE The signal strength is Good
(-95dB>RSPR≥-115dB).
3G The signal strength is Good
(-93dB>RSPR≥-107dB).
Only rst
LED on,
the other
two o
5G/4G LTE The signal strength is Poor/Terrible
(RSPR<-115dB).
3G The signal strength is Poor/Terrible
(RSPR<-107dB).
O There is no signal or no nano-SIM card is inserted.
NOTES:
• To avoid light pollution and save energy, indicators will be turned o after the
device operates normally for about 15 minutes. If indicators need to be solid
on, you can change it‘s settings on the 5G CPE conguration page.
• When a problem occurs, indicators will be automatically lighted up again to
help you check the device status. After the problem is resolved, indicators will
be turned o immediately.

17
Logging in to the 5G CPE Page
1. Ensure that the connection between your device and the PC/ router is correct.
2. Launch the Internet browser and enter http://192.168.254.1 in the address bar.
3. Enter the password to log in to the 5G CPE conguration page
NOTE:
View the label on this guide to get the default password.
Other manuals for MC7010
2
Table of contents
Languages:
Other Zte Wireless Router manuals