Picture 2
User Guide For GH80832
Features
1.RF Digital Radio Technology with no cord, less clutter, more freedom and
convenience
2.Advanced high precision optical sensor, no dust and never needs cleaning,
3. Smart mouse sleeping mode for power saving. (just click & wake it up)
4.Plug-in recharge-base for desktop operation, rechargeable batteries is good for
environment protecting.
5. 3 programmable buttons are available for more function option
Follow the instruction below to install your mouse and gain more
freedom and control on your desktop today!
1. Take off the cover of battery compartment from the bottom of mouse and insert two
“AAA” batteries correctly into the battery compartment. Mouse will not operate if polarity
is reversed. (. (Refer to picture 1)
Picture 1
2.Remove existing mouse software in your computer before installation of your wireless
mouse
3.Shut down your computer.(ignore this step when using USB
model)
4.Remove your standard mouse and plug the wireless mouse
receiver jack into the mouse port on your PC.(PS/2: refer to
picture 2; USB: refer to picture 5)
5.Position your mouse receiver with charger in a convenient
location, but please note that the receiver must not be placed
upon the computer or near any other items also operating on radio
frequency as this will affect the connection between receiver
and mouse. Picture 5
6.Restart your computer. (ignore this step when using USB model)
7.After your Windows Operation System is fully running, gently press and hold the small
oval reset button on the wireless mouse receiver for one second.
(Refer to picture 3)
Picture 3 Picture 4
8.On the underside of the mouse is a small hole marked “connect”. Press this using
a pencil point or other pointed object and release. This will register your wireless mouse
with the receiver. (Refer to picture 4)
9.Test the connection by rotating the wheel on the mouse. If it works properly, the two
small lights on your receiver will flash indicating a strong signal.
Your wireless mouse is functional at distances up to six feet. Your environmental
conditions may reduce or extend your maximum working distance. Large metal areas
and metal desks can form a barrier prohibiting smooth operation. Experiment by
positioning the receiver unit at different positions for maximum reach.
Software Installation
1.Insert floppy disk into disc drive, Select "RUN" from the start menu and type
"A:\Setup.exe", this will start the set-up application
2.Follow the instruction on the screen to complete the installation. Restart the computer,
the Mark for the mouse driver will appear in the computer.
3.Fix the function for the mouse button
1). Double click the mouse icon on the desktop to open the fixing interface
2). Choose the function of the mouse as you need
The wheel is the middle (Third) button, the button on left side is the Fourth one, and the
button on right side is the Fifth one. You can fix the function for these three buttons as
you need, totally 44 function are available.
Troubleshooting
Here are some handy tips if you have trouble installing or operating your mouse.
I can’t get my mouse registered on the receiver.
Check the connection to ensure that your mouse receiver is correctly plugged into the
port of your computer. Restart your system from a shutdown position to ensure that the
mouse is detected by your operating system. After starting up, depress the reset
button on the top of the receiver for two seconds, then press the connect button on the
bottom of mouse. Please hold the mouse at a distance of no more than six inches
from the receiver. The receiver should register the mouse immediately.
My mouse works fine up close to the receiver but acts erratically when
I move it to the desktop.
This is caused by a large presence of metal in the surrounding area. In this case,
you’d better re-position your receiver so that it could work close to the mouse.
My mouse just quit working.
First try resetting your receiver and mouse following steps 5-8. If this doesn’t work, try
changing the batteries. The power of batteries will last about 20 hours under normal use,
then should be recharged. Please use best quality alkaline batteries for maximum
performance. When replacing your batteries, ensure that you arrange the polarity
properly or your mouse will not operate. Then repeat steps 7~8.
If your mouse is suffering from interference from other mouse users, please repeat
steps 7-8 to register the mouse again.
Maintenance Of Your Mouse
If the mouse is not going to be used for a long period of time then please take out
batteries and keep in a cool, dry place.
Caution
Replace the batteries in the mouse when the batteries being used are no longer
operating the mouse efficiently. Using incorrect batteries in the mouse could cause it
to explode, for the batteries to leak or for the mouse to catch fire, causing personal
injury.
Do not break or destroy batteries, dip into water, place above 100ºC, or set on fire.
Conductors such rings, watches and keys can cause batteries to short, over heat or
even explode.
Important Expert Advice:
Long periods of repetitive mouse use can cause injury to wrists, arms, necks and backs.
If any discomfort occurs while using this mouse, we advise you to seek medical advice.
To reduce the risk of injury, please try the following suggestions;
zTake frequent breaks
zEnsure that you are using the mouse correctly
zRelax your arms and shoulders frequently
zPlace mouse and keyboard in a comfortable position
zAvoid resting your hand on the edge of your desk
Caution:
