ZTV Electron ZT-803T User manual

MODEL
ZT-803T
PAGE:
1 OF 4
PRODUCT
INSTRUCTION DESCRIPTION
Wireless Camera
ZT-803T
WIRELESS CAMERA USER’S MANUAL
REVISIONS DESCRIPTION DATE DESIGN
SHENZHEN ZHONGWANG ELECTRON CO., LTD APPROVAL
PAGES
TOTAL
FILE
NUMBER ISSUE DATE CHECK
4 DESIGN

- 2 -
FILE NUMBER MODELZT-803T PAGES: 2 OF 4
Operation instruction
1. Connecting the receiver antenna. (Figure 1)
2. Connecting the 9V/12V direct current stabilizer (Figure 2), pilot lamp lighting (Figure 3).
3. Connecting the audio and video (figure 4) output with the input to the monitor, the television should be set
on A/V model.
4. Connecting the audio and video output with the input of the transmitter.
5. Plug power jack of DC power supply(8V200mA)into the power socket of the CMOS camera(figure
6).(Battery of the same voltage is acceptable.)
6. Turning the micro-adjustment knob (figure 5) on the receiver till receiving the picture of the wireless
camera.
7. Fine tune to the desire position till the image of CMOS camera is received.
8. Adjust the lens of the CMOS camera (figure 7) to best position.
Notice
1. The machine is supplied with many different types, please provide with electric power according the value
on the label.
2. Obstructs by the building and so on will cause attenuation.
3. Normally that the machine will slightly warm up during operation.
4. Should any other malfunctions occur, please contact local distributor.
5. Under normal operational conditions, one year’s warranty is granted .if there are quality problems within 3
months, this company will unconditionally replace with a new camera.
Waning
This product is for the sole purpose of security and applicable for monitoring in residential houses,
shops and companies. The user shall observe local rules, regulations and laws, and shall be solely liable in
this regard. This company shall not be liable for any illegalities therein.
Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
Note:
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
SHENZHEN ZHONGWANG ELECTRON CO., LTD TEL[phone]
FAX[phone]
http://www.ztv.cc

- 3 -
FILE NUMBER MODELZT-803T PAGES: 3 OF 4
Technical Data
ITEM TYPE
Transmission
Frequency 2.414~2.468GHz 4cH
Electric power: DC 8V
Video input: 1.0VP-P(MAX)
Power consumption current 80mA
Audio input: 2VP-P(Max.)
Effective range(no obstacles) 30m
CMOS
IMAGE SENSOR 1/3-inch CMOS Image Sensor
CMOS TOTAL PIXELS 628*582
SYNC SYSTEM INTEMAL
MINIMUM ILLUMINATION 1 Lµx F1.2 5600°K
RESOLUTION 330TV Line
Mode: AWB (Zero color rolling)
WHITE BALANCE
Range:3200~10000°K
GAIN CONTROL AGC
S/N RATIO 48dB(Min)/60dB(TYP)(AGC OFF)
ELECTRONIC SHUTTER 1/60~1/15,000sec
CAMMA CORRECTION 0.45
OPERATION TEMPERATURE -20~60
OPERATION HUMIDITY 85%RH
SHENZHEN ZHONGWANG ELECTRON CO.,LTD TEL[phone]
FAX[phone]
http://www.ztv.cc
FILE NUMBER MODELZT-803T PAGES: 4 OF 4

- 4 -
.
SHENZHEN ZHONGWANG ELECTRON CO.,LTD TEL[phone]
FAX[phone]
http://www.ztv.cc
: Receiver Antenna
: Receiver Power Socket
: Receiver Indicator
: Audio & Video Jack
: Monitor
: Camera Power Jack
: Flip-type Channel Controller
: Adjustable Lens