ZUOWEI ZH101 User manual
National unified service hotline诮400-106-9616
NameShenzhen ZuoWei Technology Co., Ltd.
WebXXX[VPXFJDPNEmailJOGP
I. Product Introduction
1.1Product List·······················································································
1.2Parts Name·······················································································
1.2.1Host·····························································································
1.2.2Remote Control panel usage instructions···············································
1.2.3water filter bucket, sewage bucket, deodorizing component box··················
1.2.4Display screen················································································
II.Installation method
2.1Installation of sewage bucket································································
2.2Installation of water filter bucket····························································
2.3 ·················································
Installation of deodorization components
2.4Hose assembly and Host Installation·······················································
III.Usage
3.1Target group·····················································································
3.2Start-up preparation·········································································
3.3Machine cleaning·············································································
3.4Machine handling·············································································
3.5Usage schedule················································································
3.6Precautions before and after use···························································
3.7 ·······································································
Clean and disinfection
3.8Automatic mode··············································································
3.9Manual mode··················································································
3.10Parameter setting and query······························································
IV.Safety Warning················································································
V.Troubleshooting···············································································
V I. Spe cif ica t io ns·················································································
VII.Maintenance and repair··································································
VIII.Product recycling··········································································
IX.Warranty service·············································································
Table of Content
9
10
10
10
11
11
12
13
13
14
14
17
18
18
19
19
1
1
1
2
3
4
6
7
7
8
I. Product Introduction
1 . 1 Product List
Before using, please check if the following items are included in the whole
package. If any of them are missing, please contact your dealer.
Remote Control x1
Host x1
water filter
bucket x1
Sewage bucket x1 Manual x1
Deodorization
component box x1
1.2 Parts Name
1.2.1 Host
Covers
Display screen
Power Switch
Test button
Indicator light
Reset button
1
Remote Control
Stop button:Stop the current processing action;
High, medium and low display mark: from low to high, display the
intensity of wind temperature, water temperature, etc. set changes;
Wind temperature adjustment button: Touch the up arrow or down
arrow of the button to adjust the wind temperature high or low, a
total of high, medium and low three adjustable;
Water pressure adjustment button: Touch the up arrow or down
arrow of the button to adjust the strength or weakness of the water
pressure, with a total of three adjustable high, medium and low levels;
Water temperature adjustment button: Touch the up or down arrow of the
button to adjust the high or low water temperature, with a total of three
adjustable high, medium and low levels;
Poop button: In manual mode, press this button to enter the poop
handling procedure;
Pee button: In manual mode, press this button to enter the pee procedure;
Cleaning button: In manual mode, press this button to rinse the inner
surface of the working head;
Wash button: In manual mode, press this button to clean the private parts
of the person with warm water;
Dry button: In manual mode, press this button to dry;
Manual button: long press this button, it will switch to manual mode;
Auto button: Press and hold the button, it will switch to manual mode;
Poop
Pee
Clean
Wash
Dry
MT
AT
Stop
1.2.2Remote Control panel usage instructions
2
Mainline connector
Mainline connector
positioning hole
Speaker
Remote Control
Remote Control dock ATMT
Stop
Wash
Dry
Pee
Clean
Poop
C
o
v
e
r
I
n
d
i
Wind
Tem p
Water
Press
Water
Tem p
Wind
Temp
Water
Press
Water
Temp
sewage bucket
water filter bucket
Connecting head
Active latch
sewage bucket screw cap
Sewage bucket
sewage bucket screw cap seal
handle
Sealing ring
Buckle
water filter bucket
Bucket lid seal
Bucket lid
Sewage bucket
water filter bucket
1.2.3water filter bucket, sewage bucket, deodorization component box
Deodorization component box
34
Manual mode
Press the button to enter
the poop cleaning process.
Press the button to enter
the pee cleaning process.
Press the button to enter the
drying process.
Stops the current processing action.
1.2.4Display screen
Press the button will apply a
warm water wash to a person's
private parts.
Press this button to rinse the
inner surface of the working head.
Mode Selection
Manual mode
Automatic mode
Clean air
After selecting manual mode, poop, pee, clean, wash,and dry will
enter the selectable state.
When clean air is selected, the system performs a clean air operation.
When automatic mode is selected, poop, pee, clean, wash, and dry will all be
unselectable, and the system will automatically perform poop and pee processing.
Deodorizer box
5 6
Adjustment instructions
low medium high
For adjusting the water temperature high or low,
with a total of three adjustable settings
Inquiry Page
Status display
Setting page II.Installation method
2 . 1 Sewage bucket installation method
Pay attention to the sewage
bucket screw cap seal
Turn the sewage bucket lid clockwise
to the logo position
Put the bucket into the machine, and the
movable pin at the top end of the bucket
cover will be successfully stuck into the
slot of the suction port of the machine,
which means the bucket is loaded into
the correct position.
Push active latch
2Place the sewage bucket in the
sewage bin placement in Hos
3
1
Sewage bucket placement
Heating water tank
Press and hold the unlock button
downward to pull the active pin outward
To remove the bucket, press the
unlock button to pull out the movable pin.
4
For adjusting the air temperature high or low,
with a total of three adjustable settings
For adjusting the water pressure high or low,
with a total of three adjustable settings
7
Turn the bucket lid clockwise to tighten
1
2 . 2 Water filter bucket installation method
Note the water filter bucket cover seal
Place the water filter bucket into the
Host with the bucket lid facing down
2
8
Placement of water filter bucket
Tip: Remove the deodorant box is also
used in a similar reverse step
Holding the deodorant assembly box in your hand, push the deodorant assembly
into the mounting opening along the guide slot and push the deodorant assembly
to the bottom with a little pressure.
2
2.3Deodorization component installation
Reach your fingers into the groove of the front cover and lift the cover outward.
1
Slowly close the front cover
by hand. Note that the lid
suction force is large, careful
to pinch the hand
Grasp the hose sewage tube connector, first Host wire from the hose wire hole
through, then the Host connection part aligned and pressed into, and finally
the hose assembly signal wire and Host wire for line connection.
1
2.4Hose assembly with Host installation
Sewage pipe hose connect to
Host cable
Turn the hose connector clockwise to lock in the Host connection section
2
910
III.Usage
3.1Applicable people
3.1.1Without catheter, without urine volume monitoring;
3.1.2Those with no bed sores, severe dermatitis or skin;
impaired
3.1.3Body l to 35 kg;weights over equalsor
3.1.4 No serious deformation of thighs;
3.1.5The diameter of the dry and hard stool must be less than 33 mm;
3.1.6No severe hemorrhoids;
3.1.7No mental manic behavior (e.g. tearing the quilt,
grabbing the poop by hand, pulling the diaper);
3.1.8 Users should lie flat and keep the side lying less than 30°when urination
and defecation while using.
3.4Machine handling
Before moving the machine, you need to pour out the water in the water purification bucket
and clean the sewage bucket and then open the drain valve at the bottom of the water purification
bucket to empty the water inside the main machine.
Sewage bucket
water filter bucket
3.5Usage schedule
The first week of use is based on the principle of gradual increase, so that the user can gradually
adapt to the use of the care robot:
Day 1: 4H (Daytime)
Day 2: 8H (Daytime)
Day 3: 10H (Daytime)
Day 4: 12H (Daytime)
Day 5: 12H (Evening)
After that, it is recommended that each continuous use time should
not exceed 12 hours.
3.2 Start-up preparation
3.2.1Make sure the connection between the working
head and the connecting hose is intact;
3.2.2Make sure the connection between the Host and the
connecting hose is intact;
3.2.3Make sure the water filter bucket is filled, and the Host is loaded;
3.2.4Make sure the sewage bucket has been emptied and loaded into the Host;
3.2.5Make sure the deodorant component box is properly loaded into the Host;
3.2.6Make sure the hip pads are properly put on;
3.2.7Make sure the leakage protection plug is plugged into
the power supply, and the working indicator light is lit.
3.3 Machine cleaning
The machine can not be directly sprayed and washed before cleaning, you can
wipe with a cloth.
11 12
3.6.2 Precautions after use
3.6.2.1 It is recommended to perform 1 manual cleaning process before the
working head is removed;
3.6.2 .1 First turn off the machine and then take off the working head and bag pants;
3.6.2.3 After the work head is removed, it is necessary to clean the sewage bucket in time.
3.6.2.4The working head and pipe can’t forward down when taken off from host,the
pipe should lift up higher than caregivers’ height, making the remaining water and
sewage flow back to the host’s sewage bucket, then remove the pipe
3.7 Cleaning
3.7.1 Sewage bucket cleaning
Open the Host swivel panel, hold the movable latch by hand and carry it to the sink.
Withdraw the connector and lift the sewage bucket out by hand by the handle.
Turn the sewage bucket knob counterclockwise, hold the handle with one hand, hook
the bottom of the bucket with the other hand, and slowly pour the sewage into the sink.
You can open the buckle with water or water to add toilet cleaner will sewage bucket
clean will sewage bucket outside surface of the water with a clean cloth or cotton,
wipe clean, and then reassemble (see Sewage bucket installation method)
Swivel Panel
Connecting head
Active Latch
Handle
3.8Automatic mode
When the INCONTINENCE CLEANING SYSTEM is in automatic mode, the robot will
automatically start the preset program to collect excrement, clean and dry the defecation
area after the user has defecated. If you need to stop the process during operation, to stop
the current operation, click the "Stop" button on the display or tap the "Stop" button on the
remote control.
INCONTINENCE CLEANING SYSTEM starts up in manual mode by default. Automatically
switch to automatic mode after 3 minutes. After the care robot is turned on, click the button in
the main interface of the display to enter the device control interface.
3.8.1 Setting of automatic mode
3.8.1.1 Press the "Auto Mode" button on the device control interface, the system switches
to auto mode. The icons of "Poop", "Pee", "Wash" and "Dry" on the display screen are gray
and the button are not clickable. At the same time, the "Auto" button on the remote control is
illuminated.
3.8.1.2 Press the "Auto" button on the remote control, the device control interface on the
current display will switch to "Auto Mode" simultaneously. The "Poop", "Pee", "Wash" and
"Dry" icons are gray and the buttons are not clickable. state. The "Auto" button of the remote
control is illuminated.
3.8.2How the automatic mode works
3.6 Precautions during and after use
3. 6.1Attention in use
3.6.1.1After the use of the object position change (including left and right turn, sit up
again after lying down, etc.), you need to confirm whether the work head is loose,
misalignment (focus on confirming the inner thighs and soft rubber between) ;
3.6.1.2Users should lie flat and keep the side lying less than 30°when uri n a t ion
and defecation while using.
3.6.1.3Red light at the end of the machine, report equipment failure, immediately stop
using the machine, and feedback to the manufacturer.
Attention:
1. Before using the intelligent incontinence cleaning robot, check whether the Velcro on
the base of the working head is aligned with the Velcro on the pants, and whether the
working head falls exactly in the U-shaped slot of the pants (for details, please refer to the "
Instruction Manual of the Working Head").
2. After each use of the robot, you should check whether the user's skin is red or damaged,
if there is such a condition, you should seek professional caregivers for treatment in time and
wait until the user's skin is completely recovered before using the product again.
13 14
3.10 Parameter setting and inquiry
IV.Safety Warning
Hazard
试
4.1.1 It is strictly forbidden to add hot water over
40 degrees into the water purification bucket.
4.1.2 When cleaning the machine, the power must be cut off
first. Do not use organic solvents or corrosive detergents.
4.1.3 Please read this manual in detail before use and operate
the machine in strict accordance with the operating methods
and precautions in this manual. In case of redness and
blistering of the skin caused by the user's physique or improper
wearing, please stop using the machine immediately and wait
for the skin to return to normal before using it again.
4.1.4 Do not put cigarette butts or other flammable materials
on the surface or inside the Host to prevent damage to the
product or fire.
4.1.5 Water must be added to the water purification bucket,
when the residual water in the water purification bucket,
heating water tank for more than 3 days without use, you need
to clean up the residual water and then add water.
4.1.6 Do not pour water or other liquids into the Host to prevent
damage to the product or the risk of electric shock.
4.1.7 Do not disassemble the care robot by non-professional
personnel to avoid damage to personnel and equipment.
3.9Manual mode
3.9.1 Setting of manual mode
The system defaults to manual mode after the care robot is turned on, and automatically switches to
automatic mode after 3 minutes. Automatic mode switch to manual mode This can be done in the following
two ways
3.9.1.2 Press the "Manual" button of the remote control, the device control interface on the current display
will switch to "Manual Mode" simultaneously. The "Poop", "Urine", "Wash" and "Dry" icons are activated and
the buttons return to the clickable state. The buttons return to the clickable state. At the same time, the
"Manual" button on the remote control is illuminated.
3.9.2 How the manual mode works
When the INCONTINENCE CLEANING SYSTEM is in manual mode, the Host will start the preset program to
collect excrement, clean and dry the defecation area according to the manual operation information provided
by Remote Control and the display. During operation, to stop the current work, tap the "Stop" button on the
display or press the "Stop" button on the remote control.
3.9.1.1 Press the "Manual Mode" button on the device control interface to switch the system to manual
mode. The icons of "Poop", "Pee", "Wash" and "Dry" on the display screen are activated and the button are
restored to clickable state. At the same time, the "Manual" button on the remote control is illuminated.
In the system setting interface, press the water temperature adjustment 3 settings, set the water temperature;
touch the remote control water temperature adjustment key "" "" to set the water to set the water
temperature.
Click the "System Setting" button on the main screen of the display to enter the system setting interface.
3.10.1Parameter Setting
3.10.1.1 Water temperature setting
3.10.1.2 Wind temperature setting
In the system setting interface, press the air temperature adjustment 3 settings, set the air temperature; press
the remote control air temperature adjustment key "" "" to set the air temperature to set the water
temperature.
3.10.1.3 Water pressure setting
3.10.2Record Inquiry
Press the "record inquiry" button on the main interface of the display to enter the record list
interface, you can inquire about poop, pee, turn over, fault information. You can check the
information of stool, urine, turn over and trouble.
In the system setting interface, press the water pressure adjustment 3 settings, set the water pressure; press
the remote control water pressure adjustment key "" "" to set the water to set the water pressure.
15 16
Warning
试
4.2.1 Do not hit or knock the product to prevent
damage to the machine.
4.2.2 Do not pull the Remote Control connection
cable to prevent it from breaking.
4.2.3 Be sure to use the care robot in an environment with a
temperature of 5°C-40°C and humidity of 25%-85%.
4.2.4 When removing the working head, be sure to tap up
the working head above the Host first to prevent dirt left in
the hose assembly from flowing out.
4.2.5 Be sure to place the working head higher than the
Host when the machine is in operation to prevent backflow
of water.
4.2.6 Do not use heavy objects to press the hose assembly
and do not over-bend the hose assembly.
4.2.7 the correct voltage to prevent damage to the Make sure to use
machine.
AC220V
Warning
试
4.2.10This equipment must be installed and used in power supply systems
with grounding conditions.
4.2.8 If the power cord is damaged, to avoid danger, it must be replaced by
a professional from the manufacturer, its maintenance department or a
similar department.
4.2.9 For physical, perception, ability deficiencies or lack of experience
and common sense (including children) in the use of the product should be
operated under the equipment service personnel, this equipment should
not be used as children's play apparatus.
17 18
VI.Troubleshooting
Exclusion method
Failure phenomenon Failure Cause
Check if the socket is charged
Press the reset button
Contact after-sales service to
replace the leakage protection plug
Contact after-sales service to replace the fuse
Screw the bucket cover tightly
Reinstall the seal
Contact the after-sales service to replace
the bucketsewage
Troubleshoot according to the prompt on the
LCD and the voice alarm message
Put the O-ring into the groove correctly
Clean the pipe
Find after-sales troubleshooting
Clean the filter with water
Contact after-sales service
Contact after-sales service
Contact after-sales service
Find after-sales troubleshooting
Find after-sales troubleshooting
Replace
Replace
1.The socket is not powered on
2.Leakage protection plug
reset button is not pressed
3.Leakage protection
plug damaged
4.Fuse is blown
1.Bucket lid not tightened
2.Valve seal damage
Sewage bucket shell broken
Machine malfunction
O-ring not installed or misplaced
1.Clogged pipe
2.Poor pipe sealing
Clogged heating water
tank strainer filter
Clogged water pipe
1.Heater burned out
2.Damaged control board
1.Damage to the water pipe inside
the machine
2.Loose water pipe in the machine
1.Air purification device damage
2.Activated carbon filter failure
Water purification
bucket leaking
Sewage bucket
leaking
Machine stopped
working
Leakage at the
connection hose
The working head
does not spray water
Water does not heat
Water leakage in
the machine
Exhaust gas
odor is strong
Reinstall the seal
Get an after-sales service to replace
the sewage bucket
3.Rotary cover seal damaged
4.Bucket shell is broken
Tighten connectors and screws
Machineconnector not tightened
or screws not tightened
Replace filterdeodorization
3.Clogged filterdeodorization
Correctly docked hose and work head,
latch locked
Replace the seal
The connection between the
working head and the hose is
not tight
Sealing ring at the hose joint is aging
Check if there is a seam on the inner thigh
Check whether the package pants are loose
Work head centered on the body's private parts
Need to manually perform 1 stool
process before removing the working head
The fit is not tight
Loose pants
The working head is not centered
on the private part of the body
The volume of poop is small and
does not fall into the stool cavity
Anal flushing
is not clean
VII.Maintenance
7.1Take out the heating water tank partition every time (about one month),
wipe the heating water tank surface and heating water tank partition with
a clean cloth to remove water moss and other attached dirt.
7.2When the machine is not in use for a long time, please unplug the
leakage protection plug, empty the water purification bucket, dirt
buck e t, and dra i n t h e water in th e h e atin g w a t er tan k at th e s a me time.
7. 3Every six months time need to replace the deodorizing component
box to achieve the best air purification effect.
7.4Hose assembly, working head is recommended to be replaced once
every 6 months.
Note: Please cut off the power of Host during the above maintenance.
V.Specifications
Product Name
Product Model
Rated Voltage
Maximum power
3RUWDEOH6PDUW%DWK0DFKLQH
=+
220V~
2200W
Rated frequency
Rated current
Use place
50-60HZ
9A
Indoor
After plugging in the
power, press the
on/off button
machine does not
respond
The machine is
running and the
excrement is not
collected properly
Leakage at the
working head and
hose joint
Side leakage when
working head and
body fit
19
9.3.2 Product performance failure within 15 days from the date of sale, the consumer can
choose to exchange or repair.
9.2.5 Customers please read this manual in detail, we are not responsible for m achine
fa i l u r e, sk i n r ed n ess, b l i st er i n g , b ed sor es, i n f ect i o n , e t c cau sed b y w r o n g u se
IX.Warranty service
Thank you for purchasing our products, where it is under normal use, due to the quality of the
product itself caused by the failure, within the warranty period, our company is responsible
for free maintenance.
9.1.1 INCONTINENCE CLEANING SYSTEM Host free of charge for one year, the second
year free of repair service fees only charged for replacement parts: the main accessories
(working head and connecting hose assembly) free warranty period of six months. The start
date of the warranty period is based on the product invoice date.
9.2.3 Damage caused by self disassembly or repair.
9.2.4 Damage caused by force majeure (such as earthquake, fire, war, etc.).
9.1 Warranty Description:
9.2.1 No purchase invoice and warranty card.
9.2 Disclaimer:
9.2.2 Please keep the purchase invoice and warranty card as warranty proof, once the
invoice is altered, the warranty will be invalid.
9.3.3 For customers whose warranty has expired, please contact our customer service
department, and our customer service center will serve you warmly.
9.2.2 Damage to the machine caused by wrong use of voltage.
9.3 Return and Exchange Policy:
9.3.1 Product performance failure within 7 days from the date of sale, the consumer can
choose to return, exchange or repair.
VIII.Product recycling
When this product reaches the end of its life, please send it to a suitable
place to protect the environment.
)&&:DUQLQJ
7KLVGHYLFHFRPSOLHVZLWKSDUWRIWKH)&&UXOHV2SHUDWLRQLVVXEMHFWWRWKHIROORZLQJWZRFRQGLWLRQV
WKLVGHYLFHPD\QRWFDXVHKDUPIXOLQWHUIHUHQFHDQGWKLVGHYLFHPXVWDFFHSWDQ\LQWHUIHUHQFH
UHFHLYHGLQFOXGLQJLQWHUIHUHQFHWKDWPD\FDXVHXQGHVLUHGRSHUDWLRQ
&KDQJHVRUPRGLILFDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHSDUW\UHVSRQVLEOHIRUFRPSOLDQFHFRXOGYRLGWKH
XVHUVDXWKRULW\WRRSHUDWHWKHHTXLSPHQW
127(7KLVHTXLSPHQWKDVEHHQWHVWHGDQGIRXQGWRFRPSO\ZLWKWKHOLPLWVIRUD&ODVV%GLJLWDOGHYLFH
SXUVXDQWWRSDUWRIWKH)&&5XOHV7KHVHOLPLWVDUHGHVLJQHGWRSURYLGHUHDVRQDEOHSURWHFWLRQDJDLQVW
KDUPIXOLQWHUIHUHQFHLQDUHVLGHQWLDOLQVWDOODWLRQ7KLVHTXLSPHQWJHQHUDWHVXVHVDQGFDQUDGLDWHUDGLR
IUHTXHQF\HQHUJ\DQGLIQRWLQVWDOOHGDQGXVHGLQDFFRUGDQFHZLWKWKHLQVWUXFWLRQVPD\FDXVHKDUPIXO
LQWHUIHUHQFHWRUDGLRFRPPXQLFDWLRQV+RZHYHUWKHUHLVQRJXDUDQWHHWKDWLQWHUIHUHQFHZLOOQRWRFFXULQD
SDUWLFXODULQVWDOODWLRQ,IWKLVHTXLSPHQWGRHVFDXVHKDUPIXOLQWHUIHUHQFHWRUDGLRRUWHOHYLVLRQUHFHSWLRQ
ZKLFKFDQEHGHWHUPLQHGE\WXUQLQJWKHHTXLSPHQWRIIDQGRQWKHXVHULVHQFRXUDJHGWRWU\WRFRUUHFWWKH
LQWHUIHUHQFHE\RQHRUPRUHRIWKHIROORZLQJPHDVXUHV
5HRULHQWRUUHORFDWHWKHUHFHLYLQJDQWHQQD
,QFUHDVHWKHVHSDUDWLRQEHWZHHQWKHHTXLSPHQWDQGUHFHLYHU
&RQQHFWWKHHTXLSPHQWLQWRDQRXWOHWRQDFLUFXLWGLIIHUHQWIURPWKDWWRZKLFKWKHUHFHLYHULVFRQQHFWHG
&RQVXOWWKHGHDOHURUDQH[SHULHQFHGUDGLR79WHFKQLFLDQIRUKHOS
5DGLDWLRQ([SRVXUH6WDWHPHQW
7KLVHTXLSPHQWFRPSOLHVZLWK)&&UDGLDWLRQH[SRVXUHOLPLWVVHWIRUWKIRUDQXQFRQWUROOHGHQYLURQPHQW
7KLVHTXLSPHQWVKRXOGEHLQVWDOOHGDQGRSHUDWHGZLWKPLQLPXPGLVWDQFHFPEHWZHHQWKHUDGLDWRUDQG
\RXUERG\
Table of contents
