ZUUM H4X4-4K18G User manual

H4X4-4K18G
4X4 HDMI MATRIX, HDR, UHD, 4Kx2K, 18Gbps
The 4x4 HDMI Matrix Switcher allows you to route any of the 4 HDMI input sources to any of the HDMI out display
locations. It supports resolutions up to 4Kx2K 4:4:4 (HDMI 2.0).
Features:
>Connects up to 4 HDMI sources to 4 HDMI display monitors
>HDMI 2.0 with 3D, HDCP 2.2 & DVI1.1 Compliant
>Ultra-high-definition video up to 4K 60Hz @ 4:4:4 18Gbps (6Gbps per color)
>Support HDR10, Dolby Vision, HLG
>Supports up to, Dolby TrueHD, Dolby ATMOS, DTS-HD MA, DTS:X, LPCM 7.1 @ 192KHz
>Supports ARC (Audio Return Channel)
> Multiple control methods: Front panel buttons/ IR remote control/ Web UI Control/ and RS232
Control
>Built-in LCM screen & LED button at front panel provides quick view of all port connection
>Rack mountable (1U design)
>S/PDIF coaxial audio outputs allow audio to be de-embedded from HDMI outputs
>Support HDMI cable lock on each HDMI input/output port
Package Includes:
Matrix x 1 piece
IR Blaster x 1
Power adapter x 1 piece
Instructions
Panel View:
!
!
!
!
!
!

!
!
No.
Feature
LED Status
Description
1
IR receiver
N/A
Receiving IR remote signal
2
POWER
Blue ON
Power ON
Red ON
Standby
3
LCM Display
N/A
Display operating status or Menu
4
UP Button
N/A
Go up direction in Menu
DOWN Button
Go down direction in Menu
LEFT Button
Go left direction in Menu
RIGHT Button
Go right direction in Menu
ENTER Button
Execute selected function
MENU Button
Blue ON
Press to enter Menu or display current operating status
Press and hold 3 seconds to enable/disable KEYLOCK
SCENE Button
Save/Load scene
ALL Button
Select all outputs
OFF Button
Turn off select output
5
OUTPUT Buttons
Blue ON
Press these buttons to select the desired output
Monitor connected
OFF
No monitor connected
6
INPUT Buttons
Blue ON
Press these buttons to select the desired input
Video input detected
OFF
No video input
1
INPUT HDMI
N/A
HDMI input port 1~4
2
SPDIF
N/A
SPDIF audio output port 1~4
OUTPUT HDMI
N/A
HDMI output port 1~4
3
IR
N/A
External IR receiver
4
CONSOLE
N/A
RS232 command control / Firmware update
5
RJ45
N/A
WEB control interface
6
DC JACK
N/A
Power input
Notice
* In standby mode, IR remote cannot control matrix but power on matrix only
* Please press ENTER to execute any changes of menu settings

!
3.0 LCM Panel Function:
Power on Main Screen
After power on, the main screen will show matrix name and version information.
The matrix will go back to main screen if no operations in 30 seconds
Channel Switching:
Press OUTPUT 1~4 to select HDMI output (multiple selections) then press INPUT 1~4 (single selection), press ENTER to
execute.
Key Lock:
Press MENU button for 3 seconds to enable/disable key lock function.
Main MENU Option:
* 1. SWITCH
2. SCENE
3. EDID
4. ETHERNET
5. REMOTE ID
6. AUDIO SELECT
7. SYSTEM INFO
8. USB UPDATE
Operation:
l Press UP or DOWN key to move * to select an item for setting and press ENTER key to enter into subpage.
l When the selected sub-page setting is completed, press the MENU button to return to the main page
4 X 4 HDMI MATRIX
Version V1.00
OUTPUT 1 2 3 4
INPUT 1 2 3 4
KEYLOCK!

4.0 LCM Main MENU Function Operations:
4.1 SWITCH
:
(Default: 1 2 3 4)
This function is used to switch the input/output port. Enter the SWITCH menu. Press the ENTER key, then the LCM second line
INPUT will flash. Press LEFT or RIGHT button to select the output to be modified. Then press UP or Down button to select the
input port. After that, press ENTER to confirm setting.
4.2 SCENE
SCENE function provides 10 sets of channel settings to fast reload for different application.
SAVE
Save current channel setting, press UP or DOWN to select the number and ENTER to save.
It will show input number and status of audio selection.
At main screen you could use IR01 remote button Bto enter SCENE function, button 7~* (output) to select port number
1~4 to save, or use Up/Down button to select 5~10.
LOAD
Reload saved scenes, press UP or DOWN to select the number and ENTER to load.
It will show input number and status of audio selection.
At main screen you could use IR01 remote button Bto enter SCENE function, button 1~4 (input) to select port number 1~4
to load or use Up/Down button to select 5~10.
4.3 EDID: (Default: LPCM-2CH)
Because the player output display resolution will be based on TV EDID, this Matrix provides two default EDID modes:”
BUILD-IN MODE” and “COPY MODE”.
4.3.1 BUILD-IN MODE:
This mode supports video resolution up to 4K 60Hz, audio format support LPCM-2CH、LPCM-7.1、AC3、DTS. After entering
BUILD-IN MODE menu, press UP or DOWN key to select then press ENTER to confirm setting.
OUTPUT 1 2 3 4
INPUT 1 2 3 4
OUTPUT
à
SAVE
INPUT
à
LOAD
SAVE 1 2 3 4
SCENE#1 2H 3H 4A XA
LOAD 1 2 3 4
SCENE#1 2H 3H 4A XA
BUILD-IN MODE
COPY MODE

!
5
www.zuum.life ZM1072020
!
!
4.3.2 COPY MODE
:
To fully support the TV resolution and audio mode, the matrix provides “copy mode” to copy TV EDID for input source
reference. When you use the copy mode, we recommend copying the lowest resolution TV EDID. Otherwise it may cause no
picture display if the TV resolution is not able to support higher resolution.
After entering COPY MODE menu, press UP or DOWN button to select the OUTPUT (1 to 4) and press ENTER, then press UP
or DOWN button to select the INPUT (1 to 4 or ALL) and press ENTER to confirm. If selected output cannot connect with
monitor it will show “NO OUT X HPD” and return to upper menu when ENTER is pressed.
!
!
!
!
!
!
!
!
!
!
It will show EDID Write ERROR if update failed, or EDID WRITE OK if
successful.
4.4 Ethernet
* 1. IP ADDRESS
2. SUBNET MASK
3. GATEWAY
4. DHCP CLIENT
5. MEDIA TYPE
6. MAC FILTER
IP Address: (Default: 192.168.0.10)
This function can be setup MATRIX host intranet ”IP Address”, press ENTER, the left-most number of second row will flash,
then press the UP or DOWN button to change the numbers , press LEFT or RIGHT to move to another location, the move to
a position number will flash, press ENTER to complete the setting.
Subnet Mask: (Default 255.255.255.0)
1.1080P 2CH
2.1080P MULTI
3.4K30 2CH
4.4K30 MULTI
5.4K60 2CH
6.4K60 MULTI
COPY MODE
From OUTPUT : 1
COPY MODE
To INPUT : 1
IP Address
192.168. 0.10
!!!!!!!!!!!!!!!
HDMI - OUT 4
HDMI - OUT 3
HDMI - OUT 2
HDMI - OUT 1
Player - 4
Player - 3
Player - 2
Player - 1
HDMI - IN4
LPCM-2CH
HDMI - IN3
LPCM-2CH
HDMI - IN2
LPCM-2CH
HDMI - IN1
TV1 EDID
From!OUTPUT:!1!
To! INPUT:!1!
TV1 EDID
Player - 4
Player - 3
Player - 2
Player - 1
HDMI – 4
EDID
HDMI – 3
EDID
HDMI – 2
EDID
HDMI – 1
EDID
1.1080P!2CH!
2.1080P!MULTI!
3.4K30! ! 2CH!
4.4K30! ! MULTI!
5.4K60! ! 2CH!
6.4K60! ! MULTI!
!

!
6
www.zuum.life ZM1072020
This function can be setup MATRIX host intranet “Subnet Mask”, press ENTER, the left-most number of second row will flash,
then press the UP or DOWN button to change the numbers Press the ENTER, , press LEFT or RIGHT to move to another
location, the move to a position number will flash, press ENTER to complete the setting.
Gateway: (Default 192.168.0.1)
This function can be setup MATRIX host intranet “Gateway”, press ENTER, the left-most number of second row will flash, then
press the UP or DOWN button to change the numbers Press the ENTER, , press LEFT or RIGHT to move to another location,
the move to a position number will flash, press ENTER to complete the setting.
DHCP Client: (Default Disable)
When DHCP Clients setup at “Enable”, the MATRIX host will automatically get IP Address, Subnet Mask, Gateway, if setup at
“Disable”, the MATRIX Host IP Address needs to go through “ ETHERNET” menu to set IP Address, Subnet Mask, Gateway,
press ENTER, the second row will flash, then press the UP or DOWN to select DISABLE, ENABLE, then press ENTER to
complete the setting.
Media Type: (Default 100M)
This function can be setup MATRIX host intranet “Media Type, press the ENTER, the second row will flash, then press the UP
or DOWN button to select 10M, 100M, AUTO, press ENTER to complete the setting.
MAC Filter: (Default Disable)
MAC Filter can be setup with registered MAC Address in order to connect the MATRIX host Web UI, MAC Address required by
the Web page to fill in, this function can only be setup at “DISABLE”, “ENABLE”, then to press ENTER, the second row will flash,
then press the UP or DOWN to select DISABLE, ENABLE, then press ENTER to complete the setting.
4.5 REMOTE ID
:
(Default ID 4)
This function must be set to match the Matrix remote control IR01 with the matrix itself. A conflict with other device remote
controls is avoided.
After entering REMOTE ID menu, press ENTER, the LCM LINE 1 number will flash. Then Press UP or DOWN button to select
the number, and then press ENTER to confirm.
When you finish REMOTE ID setting, MATRIX remote control IR01 must also set the same ID
in order to operate normal.
IR Remote setting: Press and hold the POWER button, then press the number button which can be set from 0 to 9, total 10
groups.
These settings on IR01 remote control have to be done the first time you use the IR01 or when you change the batteries.
Subnet Mask
255.255.255.000
Gateway
192.168. 0. 1
DHCP Client
Disable
Media Type
100M
MAC FILTER
DISABLE

!
7
www.zuum.life ZM1072020
!
!
!
!
!
!
!
!
!
!
!
!
!
4.6 AUDIO SELECT: (Default H)!
This function can set the output of SPDIF to HDMI (H) or ARC (A).
!
4.7 SYSTEM INFO:
Display H4X4-4K18G Matrix firmware version!
*1. MAIN
V1.00
2. WEB
V1.00
3. CPLD
V1.00
4. IN1
V1.00
5. IN2
V1.00
6. IN3
V1.00
7. IN4
V1.00
8.OUT1
V1.00
9. OUT2
V1.00
10. OUT3
V1.00
11. OUT4
V1.00
5.0 Remote Control Function (IR01):
5.1 To command the matrix locally, setup the remote control IR01 ID with the same code of the Matrix (see 4.5). The default
code is 4. (Power+4)
5.2 Warning: These settings have to be done the first time you use the IR01 or when you change the batteries.
l IR ID setup: press and hold POWER button, then press Number key
REMOTE ID 4
OUTPUT 1 2 3 4
AUDIO H H H H
+

!
8
www.zuum.life ZM1072020
Remote control button defined:
Symbol
Function
Power on/Standby
LEFT
RIGHT
UP
DOWN
ENTER
MENU
ALL
SCENE
Output 1
Output 2
Output 3
Output 4
N/A
N/A
Input 1
Input 2
Input 3
OFF
Input 4
For example: to switch output port 1 to input port 4, press 1 (OUTPUT 1) and then press 7 (INPUT 4).
* Using quick key operation, LCM screen will jump to the output / input setting page; it will not allow you to use the front
panel button to operate the H4X4-4K18G Matrix

6.0 Remote Control Function: (CONSOLE)
H4X4-4K18G support RS232 and TCP/IP control by same command as below:
6.1
For RS232 CONSOLE:
Connect the RS232 CONSOLE port to the COM port of the host by a F/M RS232 straight cable (pin 2 to pin 2; pin 3 to pin 3, pin
5 to pin 5).
Communication format is 9600,8, N, 1 (9600 bps, 8 data bits, no parity check, 1 stop bit)
For Ethernet TCP/IP(Winsock)
Default IP address: 192.168.0.10, Port:47011
6.2 Operation Instruction format:
Command + △(Space) + Parameter + Enter
[Command]
[Description]
POWER△[y]
Power on/off
TX1△[n]
Set Input #n to output 1
TX2△[n]
Set Input #n to output 2
TX3△[n]
Set Input #n to output 3
TX4△[n]
Set Input #n to output 4
IR_ID△[p]
Set IR remote ID
SAVE△[p]
Save scene to #n
LOAD△[p]
Load scene from #n
LOCK△[y]
Panel button& IR remote control Lock/Unlock
SET_DHCP△[y]
DHCP client on/off
IPADDRESS△[x.x.x.x]
Set Matrix IP address
SUBNETMASK△[x.x.x.x]
Set Matrix subnet mask
GATEWAY△[x.x.x.x]
Set Matrix gateway
MEDIATYPE△[z]
Network speed select
MACFILTER△[y]
MAC filter on/off
STATUS
Show connection status
VERSION
Show firmware version
HELP
Help
[Symbol]
[Parameter]
n
00=off, 01~04=1~4
p
00~09=0~9
x
0~255
y
00=off, 01=on
z
00=auto, 01=10M, 02=100M
Example:
-To route input 4 to output 1, send the following string:
TX1△04Enter
-To put matrix in standby, send the following string:
POWER△00Enter

!
10
www.zuum.life ZM1072020
Commands are case insensitive.
The Matrix will reply OK once string is correct, NG in case of incorrect string
7. Ethernet Control Function:
Initial IP Configuration
1. Setup MATRIX IP Address the same as your PC with same domains. (Default 192.168.0.10)
2. MATRIX IP Address method, please refer. to “ETHERNET” section
3. Input IP Address on a web page, you can link to the Web UI of the MATRIX host.
4. Web UI Operation:
SWITCH SETTING:
Power
Control MATRIX power on and standby
Output
Display output 1~4, it can change the display name by the Aliases page
Input
Display input 1~4, this field is a drop-down menu, a drop down menu includes Input 1~4
and OFF. It can change the display name by the Aliases page.
Reload
Get MATRIX host message
Advanced
Enter into the “Advanced” page
Apply
Complete the setting
All Port
Set all outputs from input 1~4 or off at once
Advanced:

!
11
www.zuum.life ZM1072020
IP address
Change IP address
Subnet mask
Change Subnet mask
Gateway IP
Change Gateway IP
Media Type
Change 10 / 100 / Auto detect
DHCP Client
When setup at Enable, the MATRIX host will automatic get IP Address
、
Subnet Mask
、
Gateway, If setup at Disable, the MATRIX host IP Address
、
Subnet Mask
、
Gateway
need to set from Advanced page.
Auto Reset
The terminal connection people will be 4 users online at same time, this function could setup
the linking time to avoid long time linking and another user cannot use. When over the
setting link time, the terminal will automatically disconnect the link. . (0: no time setup, 1
~ 255 Minute time range that can be setup)
Scene
Click to enter Scene setup page
MAC Filter
Enter to MAC Filter to setup page
Aliases
Enter to Aliases to setup page
Device Name
Can change device name
Back
Jump back SWITCH SETTING page
Online
Term i nal con nect ion users display, the max. 4 users online.
Aliases:
l Aliases page can change input/output name, enter Apply to finish the setting after change the new name will
update and correspond to SWITCH SETTING page Output / Input.
l Press Back jump back to advanced page.

!
12
www.zuum.life ZM1072020
MAC Filter:
l MAC Filter can be setup as registered MAC Addresses to link MATRIX host Web UI. The max is up to 10 MAC
address groups.
l After MAC Address fill in, select Enable and press Apply to complete the setting.
l Press Back jump to advanced page.
Scene:

!
13
www.zuum.life ZM1072020
l Save: Save 10 sets of channel settings
l Load: Reload 1 of the channel settings
l Update: Refresh the status of Load
l Back: Back to Advanced page
Specification:
MODEL
H4X4-4K18G
HDMI Resolution support
4K@60Hz 4:4:4 18Gbps(6Gbps per color)、
1080p@60Hz 16bit、3D、HDR、Dolby vision
Audio format support
LPCM 7.1 @ 192KHz、Dolby TrueHD、
ATMOS、DTS-HD MA、DTS:X
Video Input Interface
HDMI Type A x 4
Video Output Interface
HDMI Type A x 4
Audio Output Interface
RCA x 4
IR Output Interface
3.5mm Phone Jack x 1
Ethernet Interface
RJ45 x 1
RS-232 Input/output Interface
DB9 x 1(CONSOLE)
IR Receive Angle
± 45 degree
IR Receive Distance
5M
Power Adapter
DC 12V 4.2A
Power Consumption
2.8A
Tempe ra ture
Operation: 32 to 131°F, Storage: -4 to 185°F, Humidity: up to 95%
Dimension inches
19.01” x 7.24” x 1.73”
Weight lbs
4.85
Do you Need Technical Support?
ZUUM is proud to offer free technical support to ensure your product is operating correctly.
If you are experiencing difficulties setting up this product, please call us for assistance 1-888-861-7351 or visit www.zuum.life
Table of contents