Zvox Audio AccuVoice AV110 Manual instruction

ZVOX AccuVoice TV Speaker
MODEL AV110 | SETUP & OPERATION
www.zvox.com

ii ZVOX AV110 | Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Followall instructions.
5. Do not use this apparatus nearwater.
6. Cleanonly withdry cloth.
7. Do not blockany ventilationopenings. Install inaccordance
withthe manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two bladeswithone
wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong
into your outlet,consult an electricianfor replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs,convenience receptacles, and the point
where they exit from the apparatus.
11.
the manufacturer.
13. Unplug this apparatus during lightning storms or when unused
for long periods of time.
14.
required when the apparatus has been damaged in any way,
such aspower-supply cord or plug is damaged, liquid has
been spilled or objects have falleninto the apparatus, the
apparatus has beenexposed to rain or moisture, does not
operate normally, or has been dropped.
15. Grounding or Polarization–This product may be equipped
witha polarized alternating-current line plug (a plug having one
outlet only one way. This is a safety feature. If you are unable
to insert the plug fully into the outlet, try reversing the plug.If
yourobsolete outlet. Do not defeat the safety purpose of the
polarized plug.
16. Ventilation–Slotsand openingsin the cabinet are provided
for ventilationand to ensure reliable operation of the product
and to protect it from overheating, and these openings must
not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug, or other
similar surface.This product should not be placed in a built-
in installation such as a bookcase or rack unless proper
ventilation is provided or the manufacturer’s instructions have
beenadhered to.
17. The MAINS plug or an appliance coupler is used as the
disconnect device,the disconnect device shall remain
readilyoperable.
18. CLASSII apparatus withdouble insulation, and no protective
earth provided.
19. CAUTION: Danger of explosionif the remote control battery
isincorrectly replaced. Replace only with the same or
equivalent type.
20. WARNING: The remote control battery (battery or batteries or
battery pack) shall not be exposed to excessive heat suchas
21.
placed on the apparatus.
Disposing of this appliance
Electric and electronic appliancesoftencontain valuable materials. These appliances may also
contain materialsessential forthe correct functioning of your appliance which, if handled or
disposed of incorrectly, could be hazardous to human health and to the environment. Therefore,
please do not dispose of this appliance with your household waste. Dispose of it at yourlocal
community waste or recycling center,
AccuVoice TV Speaker Model AV110 Dimensions
READ THIS FIRST
Important SafetyInstructions For ZVOX Audio System
CAUTION
RISK OF ELECTRICAL SHOCK, DO NOT OPEN
Warning: To reduce the risk of electrical shock, do not remove
cover (or back) – no serviceable parts inside. Refer servicing to
withinan equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
constitute a risk of electrical shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
THIS APPLIANCE SHALL NOT BE EXPOSED TO DRIPPING OR
SPLASHING WATER AND NO OBJECT FILLED WITH LIQUIDS
SUCH AS VASES SHALL BE PLACED ON APPARATUS.
WARNING
304.8 mm (12") 67 mm
(2-5/8")
62 mm
(2-1/2")

ZVOX AV110 | Table of Contents iii
Quick Setup Guide ...................................................................................................................................................................................................................................1
Alternative Ways To Connect The ZVOX AV110 Speaker ..........................................................................................................................................................................2
Supplied Audio Signal Cables Guide.........................................................................................................................................................................................................3
Placement Options ...................................................................................................................................................................................................................................3
Button Functions on the ZVOX Remote Control........................................................................................................................................................................................4
Still Need Assistance ................................................................................................................................................................................................................................5
Table of Contents

1 ZVOX | Quick Setup Guide
Quick Setup Guide
(This quick guide is valid for an optical digital audio connection from your TV to the AccuVoice TV Speaker. This is the most common audio output onTVs)
Follow instructions (A, B, C, or D) according tothe available TV audio out jacks.
2. Connect The Mini Optical Signal Cable
Most TVs have an optical digital output jack sometimes labelled “SPDIF
or TOSLINK” located on the side or back panel of the TV. (A)
NOTE: Be aware the optical cable and jack are not exactly square.
Similar to a puzzle piece; Position the optical cable end so it matches the
orientation of the optical jack, then push the cable into the jack. You
should hear and/or feel a “click” when the cable is correctly inserted into
the optical jack. NOTE: Remove the protective tips on the cable.
Connect the pointed end of the supplied optical signal cable to the ZVOX
speakers audio minijack input (B), then connect the opposite end of the
optical signal cable to the optical jack on the TV.
NOTE:
you can also connect the ZVOX speaker using one of the alternative
setup options. See instructions on page 2.
1. Position& Power ZVOX AV110 TV Speaker
NOTE: For brevity, the ZVOX AccuVoice TVSpeaker Model AV110 is often referred
to as the “ZVOX AV110”in thisuser manual. Only one of three audio cables and
one powercable is needed for the setup. Place the provided AAA batteries into the
provided ZVOX remote control.
Position the AV110 on any level surface near the TVand connect the power cord to
the power jack on the back of ZVOX, then connect the AC plug into an AC power
outlet. Don’t turn the ZVOX speaker on just yet.
3. Disable TV’s Sound & Turn On The
AV110
Tune your TV to a program, then use the original TV
remote to access the TVs Home Menu -> Options or
Settings -> Sound or Audio -> Speaker List or Sound
Out -> Select the Audio System, External Speaker,
or Optical Audio Out option. Menu list vary based on
TVs year and make, see TVs owners manual
Note: Not all TVs list this adjustment choice, if your
TV does not simply turn the main TV volume to zero
and continue using the ZVOX remote to control the
volume.
Using the ZVOX AV110 remote, tap the POWER
button to turn on the ZVOX speaker. You may hear
sound if not increase the volume to your preferred
level. Done
DIGITAL
AUDIO
OUT
(TV Port Example)
A) Optical port of TV set.
B) Input panel of ZVOX sound bar.
A)
Back of TV
AV110
SUB-WOOFER POWER INPUT
SUB-WOOFER OUT
B)
the best low frequency output. The supplied cable length is 9 ft and can be extended by splicing and adding
additional audio wire (Not included). While setting up the subwoofer, keep the ZVOX speaker powered OFF.
Connecting & Placement of Subwoofer
The AV110 includes an external subwoofer that should be placed behind the TV or down below (oor level) for
AV110
SUB-WOOFER POWER INPUT
SUB-WOOFER OUT
A) Sub woofer output of ZVOX Speaker.
B) Sub woofer.
A) B)

ZVOX AV110 | Connect AV110 2
B
Alternative Ways To Connect The Mini TV Speaker
If your TV doesn’t have an optical audio output, here are some other options:
CD
3.5 mm to 3.5 mm Miniplug Analog Stereo cable
Many TVs have a headphone audio out minijack sometimes labeled “Audio
Out” or “HP” not PC IN.(A)
Insert one end of the supplied analog 3.5mm miniplug to 3.5mm miniplug
cable into the TV’s headphone audio out minijack. Insert the opposite end
of the cable into the AV100 input jack labeled MINIJACK ANALOG INPUT.
(B)
Once the mini analog stereo cable is completely connected it will be
important to maintainthe TVs main volume above 50% and continue using
the ZVOX remote for volume control, If not it maycause a weak audio signal
and shut off the ZVOX speaker. Done
Note: Maintain the mainTVs volume above 50%and continue using the
ZVOX remote for volume control, If neglected it may cause a weak enough
audio signal causing the auto shut off to react.
Red&White RCAto3.5mm Analog Audio cable
Some TVs have red/white RCAjacks for analog audio output Be sure you
as “AUDIO OUTPUT” NOT “Audio IN or Comp IN”. (A)
Insert the red and white plugs into the red and white jacks onthe TV
labeled “Audio Out”.(A) Insert the 3.5mm miniplug end of the cable into the
AV100 input jack labeled MINIJACK ANALOG INPUT. (B)
Once the RCA analog cable is completelyconnected, tune your TV to a
program, then use the original TV remote to accessthe Home Menu ->
Options or Settings-> Sound or Audio -> TV Speakers -> OFF or Speaker
List, Sound Out -> Select Audio System, External Speaker, or the Optical
Audio Out option. (Menu list varies based on TVs year and make, see TVs
owners manual) If this option isunavailable keep the main TV volume at
zero and continue using the ZVOX remote for volume. Done
Note: Rarely TVs list an analog audio setting that must be set from
Variable to FIXED. If you have yet to hear sound, tap the input button on
the ZVOX remote control until the ZVOX display readsin2a. Continue
using the ZVOX remote for the volume control.
Connecting To A Cable Or Satellite TV Set Top Box
If your TV’s audio output is inaccessible (on a wall-mounted TV, for
instance) or unavailable, you can connect to the audio output of
your cable or satellite set top box to the ZVOX speaker. Most set
top boxes have an “audio output” in addition to the HDMI output
intended for use with the TV.
To connect between the cable box and the ZVOX speaker, identify
the audio output available on the back of the cable or satellite box,
then follow the cooresponding instructions in previous setup column
A or C. Note: Connecting the ZVOX speaker through this option
outputs this source only. Remember to use the audio out or digital
audio out, NOT comp-in or av-in .
Coaxial Digital Audio Out Signal/No Available Audio Out:
This ZVOX Audio soundbar does not have a coaxial-format digital
audio input. A coaxial digital to optical digital audio converter OR
a coaxial digital to stereo analog audio converter should be used.
If your TV or cable/satellite box do not have audio outputs at all a
HDMI extractor with an audio out should be used. Visit support.
zvox.com or contact ZVOX Audio at [email protected] to learn
what suitable audio converters or HDMI extractors are available.
Cable In
Network
USB
HDMI
To TV
Digital
Audio Power
LR
Analog
Audio
Cable/Satellite Set Top Box (Example)
Lorem ipsum
A. C.
(TV Port Example)
AV110
SUB-WOOFER POWER INPUT
SUB-WOOFER OUT
AUDIO OUT
HP
X
A) Analog Out/Headphone port of TV set.
B) Input panel of ZVOX sound bar.
A)
B)
Back of TV
PC
IN
R L R L
X
RCA jacks
labeled
“AUDIOOUT ”
Other
RCA jacks
(usually audio IN)
AV110
SUB-WOOFER POWER INPUT
SUB-WOOFER OUT
A)
B)
Back of TV
A) Analog Out/RCA (Red and White) port of TV set.
B) Input panel of ZVOX sound bar.

3 ZVOX AV110 | Cables and Placement
Placing The AV110 TV Speaker in Front of the TV.
Most people choose to place the ZVOX speaker in front of the TV, but it can also be placed
on any level surface near the TV – above, below or to the left or right. Choose a place that
lets you direct the ZVOX Speaker towards the TV viewers. The provided subwoofer can
response output.
• A safe, secure installation of the AccuVoice TV Speaker is the
owner’s responsibility.
• Do not place any objects on top of the ZVOX AV110 TV Speaker or the
subwoofer.
Placement OptionsSupplied Audio Signal Cable Guide
The AV110 includes two analog signal cables and one optical digital signal cable with a standard optical plug
on one end and a mini optical plug on the other end. One of these three cables will connect from most TVs
or cable/satellite set top boxes to the input on the AV110. In the rare instance your TV or cable/satellite set
top box has only an optical minijack audio output, an optical miniplug to optical miniplug cable is needed (not
Audio cables supplied with the ZVOX TV Speaker
standard optical plug
to
analog miniplug
analog miniplug
to
analog miniplug
red and white
RCA plugs
to analog miniplug

ZVOX AV110 | Remote Control 4
Button Functions on the ZVOX Remote Control
Volume
When the volume up arrow button is quickly pressed and released,
you will increase the volume. The volume down arrow button quickly
pressed and released, decreases the volume.
AccuVoice
Pressthe AccuVoice buttonto select the AccuVoice function. Additional
presses of the AccuVoice buttonallow you to select increasing
levelsof voice enhancement. There are six levelsof increasing voice
enhancement, starting with AccuVoice 1 going up to 6. (A1-A6) will appear
to indicate which AccuVoice mode you are selecting. The default setting is
AccuVoice 1. If you were to press the AccuVoice button once will indicate
AccuVoice 2 mode.The setting you select remains the default AccuVoice
setting until you decide to change it.
SuperVoice
Pressand hold the AccuVoice button for 5 secondsto select the Super-
Voice function. Additional presses of the AccuVoice button allows you to
select increasing levels of voice enhancement. There are six additional
levelsof increasing voice enhancement, starting with SuperVoice 1 going
up to 6. (S1-S6) will appear to indicate which Supervoice mode you are
selecting. The setting you select remains the default AccuVoice setting until
you decide to change it. To go back to Accuvoice, repeat the process.
Power
The Power button switches the AV110 between off and on. When the
AV110 is powered on, you will see the “On” appear on the front speaker
“OF”.
Note: The ZVOX AV110 will also enter STANDBY if it receives a low or
no audio signal for 20 minutes. To disable this feature: While the ZVOX
speaker is OFF “OF” press and hold the Power button for 5 seconds, “nA”
will appear indicating the feature has been disabled. “Ao” indicates the
feature is enabled.
Master Reset: While ZVOX speaker is On, press and hold the Power
button on the ZVOX remote for 5 seconds. The system will reset to factory
default and turn back on.
Mute
Tap this button to MUTE the ZVOX speaker. When the MUTE function is
active, the display blinks “00” repeatedly. The Mini will enter STANDBY if
it is left in MUTE for longer than 5 minutes. You would then see the amber
Controlling the ZVOX TV Speaker With Preferred Remote
The ZVOX TV speaker “learns” to respond to one of many cable/satellite or TV remote
controls. The supplied ZVOX remote control will always adjust the ZVOX AV110 even
after the preferred TV remote is programmed to control the ZVOX speaker. Refer to
the ZVOX support page support.zvox.com for universal instructions or instructions

STILL NEED ASSISTANCE? If your TV is not the same as the
descriptions in this guide, don’t hesitate to send an inquiry to info@
zvoxaudio.com or call ZVOX Audio at [phone]. Please provide
your TV brand and model number. A ZVOX Audio representative should
be available (Eastern Time Zone) 9:30 AM to 7:30 PM Monday through
Friday and 10:30 AM to 5:30 PM on Saturday. For further information
about additional options, please refer to the ZVOX Audio website, www.
zvoxaudio.com.
USA Warranty & Registration
For warranty information applicable to an AV110, please visit this webpage:
https://zvox.com/pages/warranty-returns
zvox.com/pages/product-registration
support.zvox.com
4001201 2021
Copyright ©2021, ZVOX Audio, LLC, All rights reserved.
Design, programming and user interface are propietary designs of ZVOX Audio, LLC.