ZyCast digi-MOD RL-DM4000D Instructions for use

SETTINGS DEFAULT SETTINGS OPTIONAL SETTINGS
Channel Output 21 UHF 6 - 69
FEC (Forward Error Correction) 3/4 1/2, 2/3, 3/4, 5/6, 7/8
Guard Interval 1/16 1/2, 1/4, 1/8, 1/16, 1/32
Constellation 64 QAM 16 QAM
OFDM Mode 8K 2K
RF Output Normal Inverted, C.W.
Video Input PAL NTSC
Brightness 128 0 - 256
Contrast 128 0 - 256
Saturation 128 0 - 256
Sharpness 64 0 - 128
Hue 128 0 - 256
Cell ID 0 Adjustable
TS ID 1 Adjustable
Network ID 100 Adjustable
ORG Net ID 10 Adjustable
Network Name resi-linx Adjustable
Program Number 1000 / 2000 / 3000 / 4000 Adjustable
Channel Name CHANNEL-1 / 2 / 3 / 4 Adjustable
by
®
OK
digi-MOD RL-DM4000D
Radio Frequency Range
Quad Input SD Digital DVB-T Modulator
R
RL-DM4000D
Video and Audio Inputs x 4
12V DC Power Input ED Ind
IR Repeaters x 4
Remote Power SwitchD Indicator Input
I
J
K
L
Reset Button
LCD Display
IR LED Display
Scroll up / down Buttons
Enter Button (OK)
LED Indicator Input
IR
JJ
L
K
IN3
IN1
IN4
IN2
OFF ON (REMOTE) PWR
IR REPEATERS
REMOTE SET UP
DC 12V
1 2 3 4
RF OUT
Video Audio L Audio R
Video Audio L Audio R
Video Audio L Audio R
Video Audio L Audio R
ON
OFF
ANT IN 1 2 3 4
5 6 7 8
INPUT
TV OUTPUTS
AUX MOD RF IN
MOD RF IN
(PWR/IR PASS)
IR
IR LED
PWR LED 12V DC
GAIN
FM TRAP
®
N15275
PATENTED
RL-RF380
12V DC
3A
AV SOURCE x 4
IN3
IN1
IN4
IN2
Video Audio L Audio R
OFF ON (REMOTE) PWR
IR REPEATERS
REMOTE SETUP
DC 12V
1 2 3 4
RF OUT
Video Audio L Audio R
Video Audio L Audio R
Video Audio L Audio R
Screw Holes for Wall Mounting Brackets
RF Output
Remote Setup
icator Input
A B C DEA
B
C
D
E
F H I
G
F
G
H
INPUT OUTPUT
Video Input CVBS Output Level 85 dB V
Video Input Level 0.7 - 1.4 V (pp) Output Impedance 75 Ohms
Video Mode PAL / NTSC Channel bandwidth 7 MHz / 8 MHz
Audio Input Stereo Output Level Adjustment 20 dB typ.
Audio Input Level 0.4 - 4.8 V (pp) MER >30 dB typ.
Input Connectors Video (RCA) - Audio (RCA) Connector Type “F” female
Input Impedance 75 Ohms
MODULATION GENERAL
Video Resolution PAL 720 x 576 @ 25fps Power Supply 12 Volts DC 3 Amps
Video Compression MPEG2 MP@ML Consumption 1.7 Amps
Audio Compression MEPG1 Layer 2 Dimensions 300 x 200 x 47 (mm)
Weight 1.86 Kg
Quick Install Manual
ZyCast
www.digi-modbyzycast.com
WARRANTY
digi-MOD states that the warrant that the customer can rely on is that provided by the manufacturer.
In the event of any warranty claim please contact your place of purchase and it will be forwarded it
to the manufacturer. The manufacturer will then determine the extent of their liability.
ZyCastR

All settings will remain
unless a factory default is done.
1. Power Up the digi-MOD
2. Enter Password “0000” and press “OK”
3. Wait until digi-MOD reads “SD SERIES” then enter the menu by selecting the “OK” button
4. The LCD screen will now display “COMMON SETUP” - select the “OK” button
5. The LCD screen will now display “OUTPUT CHANNEL”. Select the “OK” button. In some TV sets
Channel 21 is not available, so it is recommended to change this to appropriate available output channel
to suit your installation (40, 50, etc.) Once you have scrolled and selected a channel number, Select
“OK” to lock in the change
6. Change any other settings via the “MENU” as required
7. TO MAIN”,
select “OK”
8. Auto Scan for Channels on the TV set with the digi-MOD connected and powered.
9. Sources for selected digi-MOD Channel selection, (e.g channel 40), are found on TV channels 101, 102,
103, 104 (adjustable - refer to Programming LCN)
Initial Startup
Programming
Installing multiple digi-MOD’s in an installation
Please ensure each digi-MOD has different settings in the categories below if you are installing 2 or more in
an installation.
OUTPUT CHANNEL
STREAM ID
CHANNEL NAME
LCN
NOTE:
correctly.
CHANNEL NAME can be changed by using the Scroll “UP” key until you reach “ENCODER SETUP”.
Select the Encoder you want to adjust (1,2,3,4), Scroll to “CHANNEL NAME”. Use the UP/DOWN scroll
LCN (Logic Channel Number) can be moved from its default position (101, 102, 103 and 104) to a different
channel number (e.g. 4, 5, 6, 8) by scrolling UP/DOWN in the ENCODER SETUP, Select the Encoder you
want to adjust (1,2,3,4), Scroll to LCN. Once selected, press the “OK” button to lock your LCN Number.
NOTE: Repeat this process for each Input of your digi-MOD Modulator.
1. Connect the RCA cable from the video source (eg: Cable TV, Pay TV, DVD, VCR, Camera) to the yellow
RCA Video Input (Video) on the rear of the RL-DM4000D Modulator.
2. Connect the RCA cable from the audio source to the red/white Audio Inputs (Audio L & R) on the
rear of the RL-DM4000D Modulator.
3. Connect the RF Output from the RL-DM4000D to the Modulator Input on the RF Distribution Module
RL-RF380. Alternatively connect the RF Output to an existing distribution system or directly to a
television set.
4. Connect the supplied 12V DC Switch Mode Power Supply to the Power Input .
5. Repeat steps 1 - 3 for connection of other sources to AV Inputs IN2 - IN4.
6. Slide the Remote Power Switch to “ON” if connecting the Modulator to a RL-RF380 Video Hub.
7. Connect IR emitters RL-IR700/800 to the outputs on the rear of the RL-DM4000D Modulator. Place
the other end within 25mm of the IR receiver on the AV source (depending on environmental conditions).
Hardware Connection
G
Safety Precautions
•Do not apply power to the DVB-T Digital IR Modulator until all components have been installed and all wiring has
been properly terminated. Failure to do so may result in damage to the product and void manufacturer’s warranty
•Do not Adapter from the DVB-T
Digital IR Modulator
•Do not expose any component to moisture. Doing so can create electrical hazards or render the component
unusable. Exposure to moisture will also void the warranty on the system.
•This modulator is powered with a voltage of 12 VDC. The power supply voltage must not exceed this, otherwise this
modulator could suffer irreparable damage and subsequent invalidation of the warranty.
Note:
- Do not replace the power supply with a voltage greater than 12 VDC.
- Do not connect the modulator to the power if the power cord is damaged.
- Do not plug the modulator into the mains supply until all cables have been connected correctly.
- Do not cut the cord.
•Avoid placing the modulator next to central heating components and in areas of high humidity.
•Do not cover any modulator elements that could obstruct the ventilation slots and cause overheating.
•If the modulator has been kept in cold conditions for a long time, keep it in a warm room no less than 2 hours before
plugging it into the mains.
•Do not place digi-MOD on top or underneath a PVR Device, as this could cause overheating.
I
F
K
F
K
H