Zycoo UC510 User manual

IP Office for SOHO
UC510/UC520
www.zycoo.com
Quick Installation Guide
Quick Installation Guide
e1 2 3 4
IP Off ice for S OHO

1 Package Contents
2 Hardware Installation
2.1 Safety Precautions
2.2 Product Installation
2.3 Physical Connection
2.4 LED Definitions
3 Basic System Configuration
3.1 Web Login
3.2 Network Configuration
3.3 PBX Configuration
3.4 Reset to factory
4 Further Configuration
Table of Contents
03
1 Package Contents
Warranty Card
Power Cord
IP Office for SOHO
Thank you for purchasing ZYCOO IP Office for SOHO. These are the items
included with your IP Office for SOHO purchase:
Quick Installation
Guide
03
04
04
07
07
08
08
08
09
12
15
15
e1 2 3 4
IP Office for SOHO
3G/LTE Antenna
for UC520 Only

0504
2 Hardware Installation
The followings are instructions for setting up ZYCOO IP Office for
SOHO. Please refer to the illustration and follow the simple steps
below to quickly install your IP Office for SOHO.
2.1 Safety Precautions
Notes:
To avoid any device damage and bodily injury caused by improper
use, please observe the following rules.
Keep the power off during the installation.
Use only the power cord provided with IP Office for SOHO .
Make sure that the supply voltage matches the specifications indicated on the rear
panel of IP Office for SOHO.
Confirm not to bring about the overload of power circuit before turning on the
power of IP Office for SOHO, to avoid the unnecessary damage.
To avoid the electric accident, do not open or remove the cover of IP Office for
SOHO when it is working as well as off the power.
Before cleaning the device, cut off the power supply. Do not clean it by the
waterish cloth, and never use any other liquid cleaning method.
Site Requirements
40 C
0 C
To ensure normal operation and long service life of the device,
please install it in an environment that meets the requirements
described in the following subsection. Please keep a proper
temperature and humidity in the equipment room. Too high/low
humidity may lead to bad insulation, elec tricity leakage,
m e c h a ni ca l p ro p e r ty c h a n ge s a n d co rr o s io ns . To o h i g h
temperature may accelerate aging of the insulation materials and
can thus significantly shorten the service life of the device. For
normal temperature and humidity of the device, please check the
following table.
Environment
Operating
Storage
Temperature
0 C~40 C
-20 C~55C
Humidity
10%~90%RH Non-condensing
5%~95%RH Non-condensing
Clearness
The dust accumulated on IP Office for SOHO can be absorbed by
static electricity and result in poor contact of metal contact points.
Some measures have been taken for the device to prevent static
electricity, but too strong static electricity can cause deadly
damage to the electronic components on the internal circuit board.
To avoid the effect of static electricity on the operation of IP Office
for SOHO, please dust the device regularly, and keep the indoor air
clean.
e1 2 3 4
IP Offi ce for SO HO
e1 2 3 4
IP Offi ce for SO HO

Electromagnetic Interference
Electronic components including capacitance and inductance on
the device can be affected by external interferences, such as
conducted emission by capacitance coupling, inductance coupling,
and impedance coupling. To decrease the interferences, please
make sure to take the following measures:
Use the power supply that can effectively filter interference from
the power grid.
Keep the devices far from high-frequency, strong-current devices,
such as radio transmitting station.
Use electromagnetic shielding when necessary.
Note: To avoid any device damage and bodily injury caused by
improper use, please obey the following requirements for
installation and maintenance.
2.2 Product Installation
Module Installation
This IP Office for SOHO can support two analog ports, whose
combinations are as follows:
2FXO 1FXS+1FXO
e1 2 3 4
IP Offi ce for SO HO
PHON E LINE LAN4 LAN3 L AN2 LAN1 WAN USB2 U SB1 Turbo
The module is default installed in the device before releasing from
factory. It’s forbidden to open the housing box and change the
module by yourself; Otherwise Warranty Void.
Do not touch any module on the device, just to prevent the module
from being damaged by static electricity.
Note:
2.3 Physical Connection
PC
PHO NE LIN E LAN 4 LAN 3 LAN2 LAN 1 WAN USB 2 USB1 Turb o
PSTN
Phone Power
ITSP
0706

2.4 LED Definitions
Indication Function Status Explaination
Power Status
On
Off
On
Off
200ms Blink
100ms Blink
Power On
Power Off
WSC Succeeded(Off after 300s )
WPS Ready or Disabled
WSC Running
WSC Failed
Data Transport
Blink
Off
Wireless Status
FXO
FXS
3G/4G Status
(UC520 support)
Blink
Off
On
Off
On
Off
On
Off
Wi-Fi
1
2
3G/4G
On
Blink
Off
Disconnected
Data Transport
Disconnected
Wi-Fi enabled
Wi-Fi disabled
Module Works
Module Loading Succeeded
or Data Transport
No Module, or No SIM card,
or Not Working
LAN(1..2..3..4) Data Status
3 Basic System Configuration
Step 4. Enter the default address “http://192.168.1.1:9999” of
the UC510 into the browser.
Step 1. Connect the network cable to the UC510 WAN port.
Network connection mode of WAN port is DHCP by default.
Step 3. Start a web browser: Internet Explorer (version 7.0 or
higher), Firefox or Chrome.
Step 2. Connect a computer and the UC510 LAN port in the same
network. Ensure IP address of computer is in the
192.168.1.X segment. Default IP of UC510 is 192.168.1.1.
3.1 Web Login
Step 5. Enter the defau lt username(admin) and passwo rd
(admin). Then click “Login” to enter the graphic user
interface to set.
Default URL address: http://192.168.1.1:9999
Default Username: admin
Default Password: admin
Channel Loading Succeeded
ChannelLoading Failed
Channel Loading Succeeded
Channel Loading Failed
PWR
WPS
WAN
LAN
WPS Status
WAN Data Status
3.2 Network Configuration
Go to Router Gateway Internet WAN
It supports several modes for internet connection: PPPoE(ADSL)/
DHCP(Auto config) /STATIC(fixed IP)/ LTE(for UC520 only).
3.2.1 PPPoE(ADSL):
WAN Connection Type: Select “PPPoE(ADSL)”
0908
Notice：WPS (Wi-Fi Protected Setup), WSC (Wi-Fi Simple Configuration)

You need to input the username and provided by the ISP
(Internet Service Provider), then dial-up to the internet by the
equipment.
password
3.2.2 DHCP(Auto Config):
WAN Connection Type: Select “ DHCP(Auto Config)”
Accessing Internet with the IP assigned by the ISP(Internet
Service Provider) automatically; no need to configure anything.
3.2.3 STATIC(fixed IP):
WAN Connection Type: Select “ STATIC(fixed IP)”
You need to input the fixed IP address, subnet mask, gateway and
DNS Server.
3.2.4 LTE
LTE is default supported by UC520 only. WAN Connection Type:
Select ”LTE”
You need to input the username and password provided by the
ISP(Internet Service Provider). Then dial-up to the internet by the
equipment.
If any questions, please contact your local ISP(Internet Service Provider).
Note:
1110

3.3 PBX Configuration
Step 1: Go to PBX Extensions Extensions
Extension Settings
Extension：The account number for registration
Password：The password for registration
Step 2: Go to PBX Extensions Trunk
Trunk Settings
Create FXO trunks to connect to PSTN network
Step 3: Go to PBX Extensions Outbound Routes DialRules
Configure DialRule
1312

Notice: Use this way to recovery system when the system cannot be
started or in abnormal situation.
4 Further Configuration
Thank you for the purchase of ZYCOO products. The above steps
introduce simple configuration for IP Office for SOHO. For further
configuration, please refer to the user manual. If you have other
questions, please contact the local dealer or distributor from
which you purchased this product.
You can also browse our online FAQ resource at the ZYCOO Web site
first to check if it could solve your issue. If you need more support,
please contact ZYCOO support team.
ZYCOO online FAQ:
www.zycoo.com/html/Knowledge_Base.html
Support team email address:
[e-mail]
Copyright © ZYCOO Co., Ltd. 2014 All Rights Reserved
3.4 Reset to factory
Recovery configuration files
When a system failure occurs, you can reset the system to factory
default by pressing the turbo button for 5 seconds, and then
release the button.
Recovery whole system
Press the "turbo" button for 5 seconds when the device is power
on, the system will be in recovery mode to be restored.
Step 4: Go to PBX Extensions Outbound Route DialPlans
Configure DialPlan
Select PSTN into DialPlan1, then the extension number 810 can call
external phones with dial plan1.
Place this call through：Choose the FXO trunk
Custom Pattern：Define dial rule(XXX. represents any 4-digits or
more than 4-digits numbers; because the default
extension number is 3-digits, such dial rule cannot
conflict with extension number)
Create a dial rule which can call to external phones via a specified
FXO trunk
Notice: Please back up the configuration file before reset.
1514