ZyXEL Communications LTE4506 User manual

1/2Copyright © 2016 ZyXEL Communications Corp. All Rights Reserved
Quick Start Guide
LTE4506
4G LTE-A HomeSpot
See the User's Guide at www.zyxel.com for more information, including customer support and safety warnings.
1Make sure the LTE4506 is turned off. On the bottom of the LTE4506,
open the cover of the micro SIM card slot.
Hardware Installation
1
1
1
Gently push the SIM card into the SIM card slot. Put the cover back
in place.
Note: Please do NOT use a nano-SIM to micro-SIM card adapter to
avoid slot pin damage.
Select the type of plug used in your country. Insert the plug in the
micro USB power adaptor until you hear a "click".
Use the included power adaptor (that has an output of 5V at 1.5A
or higher current) to connect the LTE4506 micro USB port to an
appropriate power outlet. Press the power button to turn it on.
LTE4506 Wi-Fi is enabled by default. To disable or enable it again,
press the Wi-Fi button on the top of the LTE4506 for one second.
To initiate WPS to set up a secure Wi-Fi connection
between the LTE4506 and a wireless client, press the
Wi-Fi button on the top of the LTE4506 for longer than
five seconds.
Use an Ethernet cable to connect a computer to the Ethernet port
of the LTE4506 for initial configuration or Internet access.
6
POWER ON
RESET
SIM
SSID1: ZyXEL_“last four digits
of the MAC address”
Key: XXXXXXXXX
Key: XXXXXXXXX
SSID2: ZyXEL_“last four digits
of the MAC address”_5G
2
3
4
1
5
1
6
Insert SIM Card into slot
Bottom
RESET
SIM
Press for 1 Second: Turn On Wi-Fi
WIFI ON
> 5 Seconds: WPS ON
WPS ON
Optional
3
1
2
4
6
5

2/2Copyright © 2016 ZyXEL Communications Corp. All Rights Reserved
EU Importer: ZyXEL Communication A/S∣Generatorvej 8D, 2860 Søborg, Denmark∣http://www.zyxel.dk
US Importer: ZyXEL Communications, Inc∣1130 North Miller Street Anaheim, CA 92806-2001∣http://www.us.zyxel.com
Troubleshooting
Power and Hardware Connections
- Make sure the SIM card is correctly installed in the LTE4506.
- Make sure the micro USB cable is connected correctly.
LTE4506 Access and Login
- Make sure you are using the correct IP address.
• The default IP address is 192.168.1.1.
• If you changed the IP address and have forgotten it, you have to
reset the device to its factory defaults.
- Make sure your Internet browser does not block pop-up windows
and has JavaScript enabled.
- Make sure you have entered the user name and password correctly.
the default password is 1234. If this does not work, you have to reset
the device to its factory defaults.
Internet Access
- Make sure you insert an LTE SIM card into the card slot before turning on
the LTE4506.
- Log into the web configurator (admin, 1234 are the default username and
password).
Click Setup Wizard, then check the settings in Step 1 Set Up Internet
- Make sure your LTE SIM card’s account is valid and has an active data plan.
- If you are using a pre-paid SIM card, insert the SIM card on another LTE
device to check if the SIM card still works. If the SIM card works without
any problems on another LTE device, contact the vendor. If the SIM card
doesn’t work, contact your service provider.
Wireless Connections
- Make sure the wireless LAN is enabled on the LTE4506.
- Make sure the wireless adapter (installed on your computer) is working
properly.
- Make sure you are using the correct SSID and key.
Connect your mobile device to the LTE4506 wirelessly.
Open the web browser from your mobile device and enter the default
management IP address (192.168.1.1).
Enter the user name admin and password 1234, then tap Login.
The Home screen appears. Tap SSID 1 or SSID 2 to change the
default settings. Make sure the correct SSID (2.4G or 5G) is enabled.
Use the new settings to reconnect.
1
1
Via a Computer or Notebook
1
2
Via a Mobile Device
Connect your computer or notebook to the LTE4506 using an
Ethernet cable.
Open the web browser from your computer and enter the default
management IP address (192.168.1.1).
Enter the user name admin and password 1234 , then click Login.
Note: You will be forced to change the default password after first
login.
The Home screen appears. Click Setup Wizard to change the
default Wi-Fi settings
in Step 2 Set Up Wi-Fi .
1
1
192.168.1.1
192.168.1.1
User Name: admin
Password: 1234
User Name: admin
Password: 1234
1
2
1
2