ZyXEL Communications P-334WT User manual

P-334WT
802.11g Wireless Broadband Router with Firewall
Quick Start Guide
Version 3.60
1/2006
Table of Contents
ENGLISH 3
DEUTSCH 19
ESPAÑOL 36
FRANÇAIS 53
ITALIANO 70
繁體中文 87

ENGLISH
3
Overview
The P-334WT is a broadband router with a built-in four-port 10/100 Mbps switch. The P-334WT makes it easy
to set up a small home or office network and share Internet access via a broadband (cable/DSL) modem.
You should have an Internet account already set up and have been given most of the following information.
Table 1 Internet Account Information
See your User’s Guide for background information on all features.
The follow lists what you need to do:
Your device’s WAN IP Address (if given): ______________
DNS Server IP Address (if given): Primary _____________, Secondary ______________
Connection Type:
Ethernet Service Type: _______________________
User Name: ____________
Login Server IP Address: ______________
Password: ____________
PPTP: User Name: ____________
Your WAN IP Address (if given) ____________
Connection ID (if required): ____________
Password: ____________
PPTP Server IP Address: ___________
or PPTP Domain Name: ___________
¦PPPoE (PPPoE) Service Name: ____________
User Name: ____________ Password: ____________
1Hardware Connections 2Accessing the Web Configurator
3Internet Access Setup

ENGLISH
4
1 Hardware Connections
Do the following to make hardware connections for initial setup.
WAN Connection
Connect your modem to the “WAN” port using the cable that came with your modem.
LAN Connection
Connect your computer to a "LAN" port using the included Ethernet cable
POWER Connection
Use the included power adaptor to connect the POWER socket to an appropriate power source (see the User’s
Guide for power adaptor specifications by region).
The LEDs
Look at the front panel LEDs. When
you connect the power, the PWR and
WLAN LEDs come on.
The LAN and WAN LEDs turn on if the
corresponding connections are
properly made.
1
2
3

ENGLISH
5
2 Accessing the Web Configurator
1Launch your web browser. Enter “192.168.1.1” as the web site address.
Note: If you do not see the next screen, then please go to section 4.1.
Note: The Next button is located on the bottom right of each screen.
2The Password window displays. Enter the
password (“1234” is the default) and click Login.
3Change the password in the screen that follows
and click Apply.
4Click Go to Wizard setup and click Apply to set up
your P-334WT for the first time.
5Choose your language from the drop-down list
box. Click Next.
6Click Next to proceed with the Connection Wizard.

ENGLISH
6
3 Internet Access Setup
Note: Enter the Internet access information exactly as given to you by your ISP in each wizard screen
and then click Next to continue or click Back to return to the previous screen.
Current screen information will be lost if you click Back.
System Information
Wireless LAN
Configure ONE of the following wireless security types on the P-334WT:
•Auto security: Use OTIST to automatically generate a pre-shared key. View the generated pre-shared key in
the Wireless LAN screen.
Note: Your wireless clients must support WPA-PSK and use the same key.
•None: Have no wireless LAN security configured. If you do not enable any wireless security on your P-334WT,
your network is accessible to any wireless networking device that is within range.
•Basic security: WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless net-
work. The higher the WEP Encryption, the higher the security but the slower the throughput.
•Extend (WPA-PSK or WPA2-PSK) security: Configure a Pre-Shared Key. Choose this option only if your wire-
less clients support WPA-PSK or WPA2-PSK respectively.
Note: The wireless clients and P-334WT must use the same SSID, channel ID and WPA(2)-PSK (if
WPA(2)-PSK is enabled) or WEP encryption key (if WEP is enabled) for wireless communication.
1This screen is optional. You can just click Next.
•System Name is for identifying the P-334WT. You
can enter your computer's "Computer Name".
• If you leave the Domain Name blank, the domain
name obtained by DHCP from the ISP is used.
STEP 1:
STEP 2:

ENGLISH
7
OTIST
• OTIST (One-Touch Intelligent Security Technology) allows your P-334WT to assign wireless clients the P-
334WT’s SSID and static WEP or WPA-PSK encryption settings. The wireless client must also support OTIST
and have OTIST enabled.
A Enter a unique name to identify the P-334WT in the wireless LAN.
B Leave the default setting. The P-334WT and wireless client must use the same channel ID.
C Select a level of wireless security. Choose Auto or None.
D Yes is selected by default. Select the No radio button if you don’t want to use OTIST now or your wireless
clients don’t support OTIST. If you set Security to Auto, OTIST must be enabled.
E The default OTIST Setup Key is “01234567”. This key can be changed in the OTIST screen. Be sure to use
the same OTIST Setup Key on the P-334WT and wireless clients.
Auto or No Wireless Security
D
E
A
B
C

ENGLISH
8
A Enter a unique name to identify the P-334WT in the wireless LAN.
B Leave the default setting. The P-334WT and wireless client must use the same channel ID.
C Select Basic(WEP) security.
D Select 64-bit, 128-bit or 256-bit from the WEP Encryption drop-down list.
E Select ASCII or Hex WEP key input method.
F You can create a WEP key by either:
Entering a Passphrase (up to 32 printable characters) and clicking Generate to have the P-334WT
automatically generates a WEP key.
Or
Entering manual keys in each Key (1~4) field.
G Select one of the Key radio buttons to use as the default WEP key.
H Yes is selected by default. Select the No radio button if you don’t want to use OTIST now or your wireless
clients don’t support OTIST.
I The default OTIST Setup Key is “01234567”. This key can be changed in the OTIST screen. Be sure to use
the same OTIST Setup Key on the P-334WT and wireless clients.
Basic(WEP) Security

ENGLISH
9
E
F
D
G
A
B
C
H
I

ENGLISH
10
A Enter a unique name to identify the P-334WT in the wireless LAN.
B Leave the default setting. The P-334WT and wireless client must use the same channel ID.
C Select WPA-PSK or WPA2-PSK security.
D Type a pre-shared key to have a more secure wireless connection than WEP encryption. Type from 8 to 63
case-sensitive ASCII characters.You can set up the most secure wireless connection by configuring WPA in
the advanced wireless screen. You need to configure a RADIUS server to do this.
E Yes is selected by default. Select the No radio button if you don’t want to use OTIST now or your wireless
clients don’t support OTIST.
F The default OTIST Setup Key is “01234567”. This key can be changed in the OTIST screen. Be sure to use
the same OTIST Setup Key on the P-334WT and wireless clients.
Extend (WPA-PSK or WPA2-PSK) Security
A
B
C
D
E
F