ZyXEL Communications LTE7490-M904 User manual

LTE7490-M904
4G LTE-A Pro Outdoor Router
Copyright © 2020 Zyxel Communications Corp. All Rights Reserved.
See the User's Guide at www.zyxel.com for more information,
including customer support and safety warnings.
Quick Start Guide
1/4
EU Importer
Zyxel Communications A/S
Gladsaxevej 378, 2. th. 2860 Søborg, Denmark
https://www.zyxel.com/dk/da/
1 2
R E S E T S IM
L AN (P oE )
R E S E T S IM
L AN (P oE )
Make sure the LTE7490 is turned off. There should be no Ethernet cable connected providing
power using PoE. Unscrew the SIM card slot cover and remove it.
1Insert your SIM card provided by an LTE ISP (Internet Service Provider). 2
Step 1 SIM Card Installation
1 2 3 4
Follow steps 1 to 4 in the drawing to connect an 8-pin Cat 5e Ethernet cable to the LTE7490's LAN port.
1-4
Step 2 Cable Connections
Cat 5e
Power Injector
Power Outlet
Pole Mounting
Cat 5e
Power Injector
Power Outlet
Wall Mounting
Location Examples
Gateway
LaptopSmartphone PC
Place the LTE7490 in an open area
free of obstacles, and adjust the angle
to point it towards the base station to
have the strongest possible LTE signal.
Package Contents
LTE7490-M904 Gigabit
PoE Injector
GbE
Cable
Cable
Gland
Grounding
Wire
Quick Start
Guide
Safety
Warnings
Tapping Screws
M4x25 mm
Nylon Wall
Plugs
M8 Hex Bolt
(1.25*120mm)
x1
M8 Hex
Nut
x1
M6 Hex
Nuts
x6
x4 x4
x2
M8 Screws
Bracket-1 Main Frame U-Type
Screws
M Bracket Indoor
Bracket
M6 Washers
x6
M8 Washers
x3 x3
M8 Spring
Washers
x6
M6 Spring
Washers
Mounting Kit
x1 x1 x1 x1x2

2/4
PoE injector
Power outlet
LAN POE
1
2
34
Step 3 Cable Connections
Connect the other end of the Ethernet cable to the provided PoE injector's OUT port.
Connect the IN port of the injector to a computer with an Ethernet cable for initial
configuration.
1
2
Connect the power plug on the PoE injector to a power outlet.
Check the LED next to the SIM card slot.
3
4
R E S E T S IM
L AN (P oE )
Red
Green Blinking - Connecting to the Internet
Steady - Connected to the Internet
Blinking - Booting
Steady - Error
Step 4 Connecting WiFi to Your LTE7490 for Easy Setup
User Name
Password
Login
1234
admin
Desktop Version
https://192.168.1.1
2
R E S E T S IM
1
Amber Blinking - WiFi is on
3
Check if WiFi is on - the amber LED is blinking. If not, press the WiFi button to enable WiFi.
Remove the label from the back of the LTE7490 and put it on the injector. Connect to the
LTE7490 WiFi network using the WIFI SSID and WIFI Key on the injector label, or on your
smartphone simply scan the QR code to connect.
1
2
Screw the SIM card slot cover back into place.
3
Scan the QR code on the device label to see the
SSID and WiFi Key on your smartphone.
Login a ddress : 192.168.1.1
User Name : admin
Login Password : 1234
WiFi SSID : Zyxel_xxxx
WiFi Key : XXXXXXXXXX
PoE injector
LAN POE
R E S E T S IM
AN (P oE )
https://192.168.1.1
User Name: admin
Login Password: 1234
LTE7490-M904
User Name
Password
Login
1234
admin
https://192.168.1.1
Open a web browser and go to https://192.168.1.1.
Enter the default username (admin) and password (see label), and then click Login.
See the User’s Guide at www.zyxel.com for more information.
Configuring Your LTE7490 (Optional)

3/4
x4
Unit: mm
25.4
8.0 1
3
96mm
96mm
2
Four Nylon Wall Plugs
Wall Mounting (Optional)
Use the four corner holes of the M bracket to mark holes on a wall. Drill four holes in a wall.
1 2 Insert the screw anchors and screws into the holes.
M4 Screws
Unit: mm
x4
25.4
4.0
2.38
9
Insert nylon wall plugs into the wall. Use mounting screws to secure the main frame to the wall
through the nylon plugs.
3
Use washers, spring washers, and nuts to attach the M-type bracket to the back of the
LTE7490.
Follow steps 4-5 in the drawing to align the rotating bracket with the M-type bracket, insert the
M8 bolt through the holes, and use washers, spring washers, and nuts to secure it.
Follow steps 2-3 in the drawing to attach the rotating bracket to the mounting main frame
using washers, spring washers, and hex nuts. Do not tighten the nuts until you adjust the
mounting angle in the final step.
1
32
Spring Washers
x2
M6 Hex NutsM Bracket Bracket-1
Main Frame
x2
x2x1
x1
x1
Washers
Step 5 Pole / Wall Mounting: Connect M Bracket and Main Frame
M8 Spring Washers
x2
M8 Screws
x2
x2
M8 Washers
M8 bolt
x1
-
1
2
345
5-4

4/4
Use washers, spring washers, and nuts to attach the indoor bracket to the back of the device.
1 2 Use washers, spring washers, and screws to attach the main frame to the indoor bracket.
M8 Spring Washers
x2
M8 Screws
x2
x2
M8 Washers
Indoor Bracket
Main Frame
Table Stand (Optional)
x1
x1
Pole Mounting (Optional)
M6 Spring Washers
U-Type Screws
x2
x4
M6 Washers
x4
M6 Hex Nuts
x4
Place the U-bolt around a pole. Insert the U-bolt into the holes on the main frame. Use a wrench
to secure the main frame to the pole with the washers, spring washers, and nuts.
1
M6 Spring Washers
x2
M6 Washers
x2
M6 Hex Nuts
x2
1
2
Step 6 Pole / Wall Mounting Angle Adjustment
-40°
horizontal
+40°
+0°
horizontal
45°
vertical
-48°
vertical
Connect the PoE injector to a power outlet. Use the LTE Ally app to find the optimal LTE signal strength and manage your LTE7490.
Note: After configuring the LTE7490, turn WiFi off.
Step 7 Grounding
Secure a green/yellow ground cable (18 AWG or smaller) to the LTE7490’s rear panel using the M4 ground screw.
Attach the other end of the cable to the ground, either to the same ground electrode as the pole you installed the device on or to the main grounding electrode of the building.
Follow your country’s regulations and safety instructions to electrically ground the device properly. Qualified service personnel must confirm that the building’s protective earthing
terminal is valid.