ZyXEL Communications P-334WT User manual

P-334WT
802.11g Wireless Broadband Router with Firewall
Quick Start Guide
Version 3.60
7/2005
Table of Contents
ENGLISH 3
DEUTSCH 19
ESPAÑOL 39
FRANÇAIS 58
ITALIANO 77
中文 96

P-334WT Quick Start Guide
2
ENGLISH 3
DEUTSCH 19
ESPAÑOL 39
FRANÇAIS 58
ITALIANO 77
中文 96

ENGLISH
3
Overview
The Prestige is a broadband router with a built-in four-port 10/100 Mbps switch. The Prestige makes it easy to
set up a small home or office network and share Internet access via a broadband (cable/DSL) modem.
You should have an Internet account already set up and have been given most of the following information.
Table 1 Internet Account Information
See your User’s Guide for background information on all features.
The follow lists what you need to do:
Your device’s WAN IP Address (if given): ______________
DNS Server IP Address (if given): Primary _____________, Secondary ______________
Connection Type:
Ethernet Service Type: _______________________
User Name: ____________
Login Server IP Address: ______________
Password: ____________
PPTP: User Name: ____________
Your WAN IP Address (if given) ____________
Connection ID (if required): ____________
Password: ____________
PPTP Server IP Address: ___________
or PPTP Domain Name: ___________
¦PPPoE (PPPoE) Service Name: ____________
User Name: ____________ Password: ____________
1Hardware Connections 2Accessing the Web Configurator
3Internet Access Setup 4Bandwidth Management Wizard
ENGLISH

ENGLISH
4
1 Hardware Connections
Do the following to make hardware connections for initial setup.
WAN Connection
Connect your modem to the “WAN” port using the cable that came with your modem.
LAN Connection
Connect your computer to a "LAN" port using the included Ethernet cable
POWER Connection
Use the included power adaptor to connect the POWER socket to an appropriate power source (see the User’s
Guide for power adaptor specifications by region).
The LEDs
Look at the front panel LEDs. When
you connect the power, the PWR and
WLAN LEDs come on.
The LAN and WAN LEDs turn on if the
corresponding connections are
properly made.
1
2
3

ENGLISH
5
2 Accessing the Web Configurator
1Launch your web browser. Enter “192.168.1.1” as the web site address.
Note: If you do not see the next screen, then please go to section 5.1.
Note: The Next button is located on the bottom right of each screen.
2The Password window displays. Enter the
password (“1234” is the default) and click Login.
3Change the password in the screen that follows
and click Apply.
4Click Go Wizard setup and click Apply to set up
your Prestige for the first time.
5Choose your language from the drop-down list
box. Click go.
6Click Next to proceed with the Connection Wizard.

ENGLISH
6
3 Internet Access Setup
Note: Enter the Internet access information exactly as given to you by your ISP in each wizard screen
and then click Next to continue or click Back to return to the previous screen.
Current screen information will be lost if you click Back.
System Information
Wireless LAN
Configure ONE of the following wireless security types on the Prestige:
•Auto security: Uses WPA-PSK security with an automatically generated Pre-Shared Key. View the generated
Pre-Shared Key in the Wireless LAN screen.
Note: Your wireless clients must support WPA-PSK and use the same key.
•None: Have no wireless LAN security configured. If you do not enable any wireless security on your Prestige,
your network is accessible to any wireless networking device that is within range.
•Basic security: WEP (Wired Equivalent Privacy) encrypts data frames before transmitting over the wireless net-
work. The higher the WEP Encryption, the higher the security but the slower the throughput.
•Extend (WPA-PSK or WPA2-PSK) security: Configure a Pre-Shared Key. Choose this option only if your wire-
less clients support WPA-PSK or WPA2-PSK respectively.
Note: The wireless clients and Prestige must use the same SSID, channel ID and WPA(2)-PSK (if
WPA(2)-PSK is enabled) or WEP encryption key (if WEP is enabled) for wireless communication.
1This screen is optional. You can just click Next.
•System Name is for identifying the Prestige. You
can enter your computer's "Computer Name".
• If you leave the Domain Name blank, the domain
name obtained by DHCP from the ISP is used.
STEP 1:
STEP 2:

ENGLISH
7
OTIST
• OTIST (One-Touch Intelligent Security Technology) allows your Prestige to assign wireless clients the Pres-
tige’s SSID and static WEP or WPA-PSK encryption settings. The wireless client must also support OTIST and
have OTIST enabled.
A Enter a unique name to identify the Prestige in the wireless LAN.
BLeave the default setting. The Prestige and wireless client must use the same channel ID.
CSelect a level of wireless security. Choose Auto or None.
DYes is enabled by default. Select the No radio button and click Next to configure OTIST later.
EThe default OTIST Setup Key is “01234567”. This key can be changed in the web configurator. Be sure to use
the same OTIST Setup Key on the Prestige and wireless clients.
Auto or No Wireless Security
D
E
A
B
C

ENGLISH
8
A Enter a unique name to identify the Prestige in the wireless LAN.
BLeave the default setting. The Prestige and wireless client must use the same channel ID.
CSelect Basic(WEP) security.
DYou can generate or manually enter a WEP key by either:
Entering a Passphrase (up to 32 printable characters) and clicking Generate. The Prestige automatically
generates a WEP key.
Or entering manual keys in each Key (1~4) field and selecting ASCII or Hex WEP key input method.
ESelect 64-bit, 128-bit or 256-bit from the WEP Encryption drop-down list.
FSelect ASCII or Hex characters.
GSelect one of the Key radio buttons to use as the default WEP key.
HYes is enabled by default. Select the No radio button and click Next to configure OTIST later.
IThe default OTIST Setup Key is “01234567”. This key can be changed in the web configurator. Be sure to use
the same OTIST Setup Key on the Prestige and wireless clients.
Basic(WEP) Security
F
D
E
G
A
B
C
D
E

ENGLISH
9
A Enter a unique name to identify the Prestige in the wireless LAN.
BLeave the default setting. The Prestige and wireless client must use the same channel ID.
CSelect WPA-PSK or WPA2-PSK security.
DType a pre-shared key to have a more secure wireless connection than WEP encryption. Type from 8 to 63
case-sensitive ASCII characters.You can set up the most secure wireless connection by configuring WPA in
the advanced wireless screen. You need to configure a RADIUS server to do this.
EYes is enabled by default. Select the No radio button and click Next to configure OTIST later.
FThe default OTIST Setup Key is “01234567”. This key can be changed in the web configurator. Be sure to use
the same OTIST Setup Key on the Prestige and wireless clients.
Extend(WPA-PSK) or (WPA2-PSK) Security
A
B
C
D
D
E

ENGLISH
10
WAN
The wizard attempts to detect which WAN connection type you are using.
If the wizard does not detect a connection type, you must select ONE from the drop-down list box. Check with your
ISP to make sure you use the correct type:
1Ethernet
2PPPoE
3PPTP.
Note: If you were given Internet access settings, enter them in the following fields. Otherwise leave the
default settings and just click Next
STEP 3: