ZyXEL Communications VSG1432-B101 START V1.10 User manual

E
L
yx
el.com www.zyxel.com
802.11n Wireless VDSL2 4-port
Gateway
Firmware Version 1.10
Edition 1, 9/2010
VSG1432-B101 Series
DEFAULT LOGIN DETAILS
IP Address: http://192.168.1.1
User Name: admin
Password: 1234
Copyright 2010
ZyXEL Communications Corporation

2
Device Panels
POWER
ETHERNET 1-4
USB
WLAN/WPS
ETHERNET WAN
INTERNET
DSL WAN
POWER
ETHERNET 1-4
USB
DSL WAN
ETHERNET WAN
RESET

VSG1432-B101 Series
3
Overview
The VSG1432-B101 is a VDSL2 router and Gigabit Ethernet gateway
with a four-port built-in Ethernet switch and IEEE 802.11n wireless. The
VSG1432-B101 allows wired and wireless clients to safely access the
Internet. The built-in firewall blocks unauthorized access to your network.
The USB port allows you to connect USB memory stick or USB hard
drive for storing or sharing files through the network. Other helpful
features include Quality of Service (QoS) which allows time-sensitive
services and applications to flow more smoothly.
Safety Warnings
• Do NOT use this product near water, for example, in a wet
basement or near a swimming pool.
• Do NOT expose your device to dampness, dust or corrosive liquids.
• Do NOT store things on the device.
• Do NOT install, use, or service this device during a thunderstorm.
There is a remote risk of electric shock from lightning.
• Connect ONLY suitable accessories to the device.
• Do NOT open the device or unit. Opening or removing covers can
expose you to dangerous high voltage points or other risks. ONLY
qualified service personnel should service or disassemble this
device. Please contact your vendor for further information.
• Make sure to connect the cables to the correct ports.
• Place connecting cables carefully so that no one will step on them
or stumble over them.

4
• Always disconnect all cables from this device before servicing or
disassembling.
• Use ONLY an appropriate power adaptor or cord for your device.
• Connect the power adaptor or cord to the right supply voltage (for
example, 110V AC in North America or 230V AC in Europe).
• Do NOT allow anything to rest on the power adaptor or cord and do
NOT place the product where anyone can walk on the power
adaptor or cord.
• Do NOT use the device if the power adaptor or cord is damaged as
it might cause electrocution.
• If the power adaptor or cord is damaged, remove it from the device
and the power source.
• Do NOT attempt to repair the power adaptor or cord. Contact your
local vendor to order a new one.
• Do not use the device outside, and make sure all the connections
are indoors. There is a remote risk of electric shock from lightning.
• Do NOT obstruct the device ventilation slots, as insufficient airflow
may harm your device.
• Use only No. 26 AWG (American Wire Gauge) or larger
telecommunication line cord.
• Antenna Warning! This device meets ETSI and FCC certification
requirements when using the included antenna(s). Only use the
included antenna(s).

VSG1432-B101 Series
5
Hardware Setup
Place the VSG1432-B101 flat on a desk or table or on the stand for a
vertical installation.
Remove the VSG1432-B101’s clear plastic covers before
using it.
To connect the stand, line up the arrow on the stand with the arrow on
the bottom of the device as shown.

6
To connect your VSG1432-B101:
1. Attach the antenna and point it up.
2
3
4
5
1

VSG1432-B101 Series
7
2. Do one of the following for your Internet connection:
a. DSL WAN: Use a telephone cable to connect your VSG1432-
B101’s DSL port to a telephone jack (or the DSL or modem jack on
a splitter if you have one).
b. ETHERNET WAN: If you already have a broadband router or
modem, use an Ethernet cable to connect the ETHERNET WAN
port to it for Internet access.
3. LAN: Use an Ethernet cable to connect a computer to a LAN port for
initial configuration and/or Internet access.
4. USB: Connect a USB (version 2.0 or lower) memory stick or a USB
hard drive for file sharing. Use a USB extension cable if the stick is
too big to fit.
5. POWER: Use the provided power adaptor to connect the POWER
socket to an appropriate power source. Make sure the power at the
outlet is on. After connecting the power adaptor, look at the lights on
the front panel.
• The POWER light blinks while your VSG1432-B101 starts up and
then stays on once it is ready.
• Each LAN light stays on if the corresponding LAN port is properly
connected and blinks when there is traffic.
• The ETHERNET WAN light stays on if the ETHERNET WAN port is
properly connected and blinks when there is traffic.
• The USB light turns on when your VSG1432-B101 detects a
connected USB device.
• The DSL WAN light turns on when your VSG1432-B101 has a DSL
connection.

8
• The WLAN / WPS light flashes green and orange while WPS is in
process. It stays on green when the wireless LAN is ready and
blinks when there is traffic.
• The INTERNET light turns on when the gateway is able to access
the Internet and will blink when your VSG1432-B101 is sending or
receiving data.
If the lights do not come on, check your connections and inspect your
cables for damage. If the lights are still off, contact technical support.

VSG1432-B101 Series
9
Set Up a Wireless Network
You can set up a wireless network using the following methods:
Using Wireless Protected Setup (WPS)
Press the WPS button on the VSG1432-B101’s front panel for more than
5 seconds to turn the WPS function on.
Follow these steps to add a WPS-enabled device to the wireless network
using the WPS/WLAN button.
Place the devices you want to connect near
one another.
Press the WPS button on the VSG1432-
B101.
The WPS light blinks green and orange.
Press the WPS button on a compatible
device within 2 minutes of pressing the
button on the VSG1432-B101.
The WPS light on the VSG1432-B101
shines steadily when connected.
1
1
2
3

10
Set Up a Wireless Network Manually
The wireless LAN on your VSG1432-B101 is enabled by default. To add
a wireless client to the network, use the settings found on the bottom
panel of your VSG1432-B101, which will look similar to the following
example:
Configure wireless devices that you want to connect to the wireless
network to use the same wireless settings as the VSG1432-B101.
The default wireless settings vary for each VSG1432-B101. Refer to the
bottom panel of your device and use the provided information.
Log into the Web Configurator
Your device may already be set up for Internet access. However, you
may want or need to log on to the VSG1432-B101 Web Configurator to
perform tasks:
• Configure your Internet access settings manually
• Customize the Quality of Service (QoS) and routing features
• Create firewall and web filter rules
• Edit remote management, as well as other features
SSID: ZyXEL00561
Security Mode: WPA-PSK
Pre-Shared Key: FB373BD356