ZyXEL Communications P-660HN series User manual

www.zyxel.com
QUICK START GUIDE
P-660HN series
Wireless N ADSL2+
Modem Router
Firmware v3.70
Edition 2, 12/2008
DEFAULT LOGIN DETAILS
IP Address: http://192.168.1.1
User Password: user
Admin Password: 1234
CONTENTS
ENGLISH 3
DEUTSCH 13
ESPAÑOL 23
FRANÇAIS 33
ITALIANO 43
NEDERLANDS 53
SVENSKA 63
Copyright 2008 ZyXEL Communications Corporation
C

2

ENGLISH ENGLISH
3
Introduction
The P-660HN series are high performance routers which combine high-
speed ADSL2+ Internet access, a built-in switch, a firewall and high-speed
wireless networking capability.
How It Works
A computer can connect to the P-660HN using an Ethernet cable (a) or using
wireless connection (b). The P-660HN then connects to the Internet by
telephone wire (DSL cable) (c), providing you with seamless access to the
Internet.
Overview
• Hardware Connections, on page 5
• Internet/Wireless Setup, on page 8
a
b
c
ENGLISH

ENGLISH
4
Before You Begin
Make sure you have the following things before you set up your P-660HN.
• Internet access - account information provided by your ISP, such as
user name and password.
• Internet Explorer 6.0 or later or Netscape Navigator 7.0 or later, with
JavaScript enabled.
See the User’s Guide for all configuration details. To read the User’s Guide,
insert the CD that came in the box into your CD-ROM drive. A screen should
pop up. Navigate to the User’s Guide from this screen. If a screen does not
pop up, open Windows Explorer (click My Computer), click on the CD-ROM
drive (usually drive D) and navigate to it from there.

ENGLISH ENGLISH
5
Hardware Connections
1. DSL: Use a telephone wire to connect this port to a telephone jack.
2. ETHERNET 1-4: Use an Ethernet cable to connect a computer to this port
for initial configuration and/or Internet access.
3. POWER: Use the power adaptor provided with your P-660HN to connect
an appropriate power source to this socket.
4. Push the power switch to the on position.
 Make sure to remove the plastic sheet on the top panel.

ENGLISH
6
Look at the LEDs (lights) on the top panel of the P-660HN.
• The POWER light blinks during start-up and is green once the P-660HN
is ready.
• Each ETHERNET light turns on if the corresponding ETHERNET port is
properly connected. The lights blink when the P-660HN is sending or
receiving data through the corresponding ETHERNET port.
• The WLAN/WPS light turns on when the wireless LAN is ready. It blinks
when the P-660HN is sending/receiving data through the wireless LAN.
• The DSL light stays on if a physical DSL connection exists and blinks
when the P-660HN is initializing the DSL line.
• The INTERNET light stays on when Internet access is available and
blinks when there is data transmitted.
Launch your web browser and navigate to any web site (for example,
www.zyxel.com). The P-660HN automatically detects and configures your
Internet connection. This may take about two minutes.

ENGLISH ENGLISH
7
If you have a PPPoE or PPPoA connection, a screen displays prompting you
to enter your Internet account information. Enter the username, password
and/or system password (1234 by default) exactly as provided. Click Apply.
If the INTERNET light is off but the DSL light is on, go to Internet/Wireless
Setup on page 8and use the wizard to configure your Internet access
settings.
 If none of the LEDs (lights) are on, check your connections. Make
sure that you have the power adaptor connected to the P-660HN
and plugged in to an appropriate power source. Make sure the
power source is turned on. Turn the P-660HN off, wait for a few
seconds and turn it back on. If the LEDs are still off, contact your
local vendor.

ENGLISH
8
Internet/Wireless Setup
1. Open your browser and enter http://192.168.1.1 (the P-660HN's default IP
address) as the address.
2. Enter the admin password 1234 and click Login.
 If the login screen does not display, make sure you allow web
browser pop-up windows, JavaScripts and Java permissions.
Your computer should be also set to get an IP address
automatically from a DHCP server. See the appendices in your
User’s Guide for more information.

ENGLISH ENGLISH
9
3. It is strongly recommended that you change the admin password in the
following screen. If you change it, you will not see this screen the next time
you log in.
4. Click Apply to replace the P-660HN’s default digital certificate. The
certificate is used for authentication when using a secure HTTPS
connection over the Internet.

ENGLISH
10
5. Choose the language you want to use for the web configurator. Select Go
to Wizard setup and click Apply.
The connection wizard helps you set up your Internet connection as well as
your wireless settings.
Enter the Internet access information exactly as given to you by your
ISP in each wizard screen and then click Next to continue or click Back
to return to the previous screen.
Current screen information will be lost if you click Back.