ZyXEL Communications NWD-370N User manual

NWD-370N
Draft 802.11n Wireless PCI Adapter
Quick Start Guide
Version 1.00
Edition 1
10/2006
Table of Contents
ENGLISH 1
DEUTSCH 15
ESPAÑOL 29
FRANÇAIS 43
ITALIANO 57
РУССКИЙ 71
SVENSKA 85
繁體中文 99

ENGLISH
1
Overview
The NWD-370N is a wireless network adapter for your
desktop computer. See page 12 for a list of system
requirements.
1 Install the Software
"Install the software from the CD before you
insert the NWD-370N. Do not insert the NWD-
370N yet.
If you have already installed Funk Odyssey
Client software on the computer, uninstall
(remove) it.
1Remove the NWD-370N if you already inserted it.
2Insert the included CD into the CD-ROM drive on your
computer.
ENGLISH

2
ENGLISH
3When the following screen displays, click Setup to install
the ZyXEL utility and driver.
VIf the screen does not display, locate and
double-click autorun.exe on the CD.

ENGLISH
3
4When the following screen displays, click Next.
5Select Driver and Utility to install both the ZyXEL utility
and the driver on your computer. If you want to install the
driver only and use Wireless Zero Configuration (WZC)
with Windows XP, select Driver only (see Note for

4
ENGLISH
Windows XP Users). Click Next to accept the default file
location or click Browse to select an alternate folder.
6Click Install.

ENGLISH
5
"You will need to restart your computer after
installing the ZyXEL utility. Make sure you have
saved your work before continuing.
7When the following screen displays, select No, I will
restart my computer later. You will turn your computer off
in order to install the hardware.
Click Finish to complete the software installation.

6
ENGLISH
2 Install the Hardware
"Do not install the hardware until you have
installed the software from the CD.
1Save your work and close all applications.
2Turn off the computer and any peripheral device(s), such
as a printer.
3Unplug the computer from the power source.
4Ground yourself by wearing an anti-static wrist strap if you
have one or touching a grounded metal object. Remove
the computer cover, and then remove the NWD-370N from
its packaging.
5If the antennas are attached to the NWD-370N, remove
(unscrew) them.

ENGLISH
7
6Insert the NWD-370N into an available PCI slot. Make
sure the NWD-370N's contacts are fully seated in the PCI
slot.
7Secure the NWD-370N to the computer with a bracket
screw.
8Attach (screw) the antennas onto the NWD-370N.
9Point the antennas up.
10 Replace the computer cover.
11 Turn on your computer.

8
ENGLISH
The NWD-370N’s LEDs (lights) turn on if it is properly
inserted.
VIf the NWD-370N’s LEDs are not on after you
have installed the software and the NWD-370N,
make sure the NWD-370N is properly inserted.
3 Connect to a Wireless Network
After you install the ZyXEL utility and insert the NWD-370N,
an icon appears in the system tray.

ENGLISH
9
VIf the icon does not display, uninstall and re-
install the ZyXEL utility. See the User’s Guide
for how to uninstall the utility.
The NWD-370N automatically searches for any available
network(s) and connects to a wireless network without
security enabled. However, this wireless network may not be
connected to the Internet.
If the icon color is red, you are not connected to a
wireless network.
If the icon color is green you are already connected to a
wireless network.
Use the following steps to select and connect to a wireless
network.

10
ENGLISH
1Double-click the icon. The ZyXEL utility Link Info
screen displays. Click the Site Survey tab.
2The available wireless network(s) displays in the
Available Network List.
SSID means Service Set Identity and is the name of the
wireless network.

ENGLISH
11
3If a wireless network has no security, one of the following
icons appears next to its entry in the list.
If a wireless network has security, one of the following icons
appears next to its entry in the list.
Choose the network you want to connect to and double-click
its entry in the list.
4If a network has no security, the Link Info screen displays.
Go to step 6.
5If a network has security, the security settings screen
appears. You need to enter security information to
connect to the network. Get this information from the
network administrator. Be sure to enter the information
exactly as it was given to you.
6To access the Internet, open your Internet browser and
enter the URL of a web site in the address bar. The
network should be connected to the Internet.
If the web site displays correctly, you are successfully
connected to the Internet.

12
ENGLISH
3.1 Note for Windows XP Users
If you want to use WZC, either disable the ZyXEL utility (if you
already installed it) or just install the driver.
• To disable the ZyXEL utility, right-click the icon and select
Use Windows Zero Configuration. To activate the ZyXEL
utility again, double-click the icon and click OK.
To install the driver only, select Driver only.
System Requirements
Before installation, make sure you have a computer with the
following:
• Pentium II 300 MHz or above
• A 32-bit (v2.2) PCI slot
• A minimum of 20 Mb available hard disk space
• A minimum of 128 Mb RAM
• A CD-ROM drive
• Windows 2000 or Windows XP

ENGLISH
13
Important Information
Federal Communications Commission
(FCC) Interference Statement
The 802.11g Wireless LAN Adapter has been tested to the
FCC exposure requirements (Specific Absorption Rate).
The equipment complies with FCC RF radiation exposure
limits set forth for an uncontrolled environment, under 47 CFR
2.1093 paragraph (d) (2).
This Transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Refer to the User's Guide for general FCC statements.
Procedure to View a Product's
Certification(s)
1Go to www.zyxel.com
2Select your product from the drop-down list box on the
ZyXEL home page to go to that product's page.
3Select the certification you wish to view from this page.

14
ENGLISH

DEUTSCH
15
Übersicht
Der NWD-370N ist ein Drahtlosnetzwerkadapter für Ihren
Desktopcomputer. Eine Aufstellung der
Systemvoraussetzungen finden Sie auf Seite 27.
1 Installation der Software
"Installieren Sie die Software von der CD,
bevor Sie die NWD-370N einstecken. Die
NWD-370N jetzt noch nicht einlegen.
Wenn auf Ihrem Computer das Programm
Funk Odyssey Client installiert ist, muss
dieses zunächst deinstalliert (entfernt)
werden.
1Entfernen Sie die NWD-370N, falls Sie sie bereits
eingesteckt haben.
2Legen Sie die mitgelieferte CD in das CD-ROM-Laufwerk
des Computers ein.
DEUTSCH

16
DEUTSCH
3Klicken Sie im folgenden Bildschirm auf Setup, um das
ZyXEL-Utility und den Treiber zu installieren.
VFalls dieses Fenster nicht erscheinen sollte,
navigieren Sie auf der CD zur Datei
autorun.exe und klicken Sie doppelt darauf.

DEUTSCH
17
4Wenn das folgende Fenster erscheint, klicken Sie auf
Next (Weiter).
5Wählen Sie Driver (Treiber) und Utility (Utility), um das
ZyXEL-Utilityprogramm und den Treiber auf dem
Computer zu installieren. Wenn Sie nur den Treiber
installieren und die Wireless Zero Configuration (WZC) mit
Windows XP verwenden möchten, wählen Sie nur Driver
(Treiber) (siehe Hinweis für Windows XP-Benutzer). Klicken
Sie auf Next (Weiter), um den vorgegebenen
Standardordner als Speicherort für die Datei zu

18
DEUTSCH
verwenden, oder klicken Sie auf Browse (Durchsuchen),
um einen anderen Ordner auszuwählen.
6Klicken Sie auf Install (Installieren).

DEUTSCH
19
"Wenn Sie das ZyXEL-Utilityprogramm installiert
haben, muss der Computer neu gestartet
werden. Denken Sie daran, vorher Ihre Arbeiten
zu speichern.
7Wenn das folgende Fenster erscheint, wählen Sie die
Option Nein, den Computer später starten. Schalten Sie
den Computer aus, um die Hardware zu installieren.
Klicken Sie auf Finish (Fertigstellen), um die Installation der
Software abzuschließen.