247HelpAlert 247 ES-CAM4A User manual

247-ES-CAM4A Quick Start Guide
24 7Alert

247-ES-CAM4A Quick Start Guide
Warning
To prevent Fire or Shock Hazards, Do Not Expose This PRODUCT to Rain or Moisture.
Camera shall not be exposed to dripping or splashing and no object lled with liquids,
such as vases, shall be placed on the apparatus.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualied personnel only.
This symbol is intended to alert the user to the presence of uninsulated
“dangerous voltage”within the product’s enclosure that may be of sucient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER SERVICE-
ABLE PARTS INSIDE, REFER SERVICING TO
RISK OF ELECTRIC SHOCK
DO NOT OPEN

247-ES-CAM4A Quick Start Guide
Regulatory Comission Notices for USA
This equipment has been tested and found to comply with the limits for a digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communi-
cations. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
You are cautioned that any changes or modications not expressly approved in this
manual could void your authority to operate this equipment.
The shielded interface cable recommended in this manual must be used with this
equipment in order to comply with the limits for a digital device pursuant to Subpart B
of Part 15 of FCC Rules.

To mount the 247 ES-CAM4A to the wall,
place the camera in a position to ensure
the most comprehensive view for video
monitoring.
Unscrew the base of the camera and
remove the plate. The dots on the base of
the camera indicate the location of the
expansion bolts. Insert the expansion bolts
into the drilled holes.
Use a screwdriver to tighten or loosen the
screws and secure the 247 ES-CAM4A and
connect the device cables.
247-ES-CAM4A Quick Start Guide

247-ES-CAM4A Quick Start Guide
To get started, download the iSecurity+ app
from Apple’s App store or the Google Play
Store on your smart phone or tablet.
1. Download “iSecurity+” App
2. Connect to power
Connect the ES-CAM4A to the AC power
adapter, then plug your power cord into
the electrical outlet.

24 7Alert
3. WiFi Setup Mode
The Setup button will glow green on
initial setup.
The “Wi-Fi Setup” LEDs in the front of the camera will ash green and
orange alternatively and the ES-CAM4A will rotate when the camera is
ready for setup.
(This may take up to 2 minutes when the camera is rst powered on.)
247-ES-CAM4A Quick Start Guide

4. Connect Your Smart Phone To ES-CAM4A
Go to your device’s settings ->
Under the Wi-Fi setting, connect to the ES-CAM4A XXXX (last 4
digits of Cam ID) network.
247-ES-CAM4A Quick Start Guide
From your WiFi connection on your smart phone, click
to connect to your (ES-CAM4A XXX) Camera.

Once your device establishes connection to the ES-CAM4A, (usually
takes around 30 seconds,) launch the iSecurity+ App. If you don’t
see the pop up prompt, please close the app and re-launch it.
5. Launch iSecurity+ App
iSecurity+ app will automatically detect your camera.
When prompted, click ‘Yes’ to setup your camera.
247-ES-CAM4A Quick Start Guide

Follow the instructions in the Camera
SetupWizard to complete installation.
6. Setup Wizard
You can use your iOS/ Android devices
to access the camera anywhere in the
world. Make sure your phone has
access to the internet via 3G, 4G or
Wi-Fi for internet connection.
Once you see the page below, the
setup process has been completed.
Setup Complete
247-ES-CAM4A Quick Start Guide

Please enter your user name and password, created during
the setup process to access your ES-CAM4A.
Camera
Status
Congure
Camera
Recorded
Events
App
Settings
7. Using iSecurity+ Main Fatures Window
247-ES-CAM4A Quick Start Guide

Swipe directional controls to change
the camera Pan & Tilt view.
8. Camera Tilt and Zoom Viewer Features
Video
Record
Snap
Picture
Speaker
On/O
Mic
On/O
(Hold down to speak)
247-ES-CAM4A Quick Start Guide
Zoom Function
Zooming In - Touch the screen with two ngers together
and slide outward at an angle and the image will zoom in.
Zooming Out- Touch the screen with two ngers apart
and slide inwards at an angle and it will zoom out.

247-ES-CAM4A Quick Start Guide
LED Status Indicators
During Wi-Fi Setup Mode
Flashing Green & Orange: Setup mode “ON”
Orange: Setup mode initializing
Light O: Setup mode o
During Normal Operation
Green: Connected to iSecurity+
Orange: Connected to local Network
Flashing Orange: Not connected to any network
Setup button
Press and hold the button for 5 seconds to reset the camera.
Press and hold the button for 15 seconds to factory reset the
camera back to default setting.
24 7Alert
Troubleshooting

Safety Information
Do not point the camera directly at the sun, or else it will damage the image sensor.
Keep the camera away from heat to avoid electric shock.
Keep the camera away from rain and moisture.
Do not attempt to open, dismantle, repair, or service the camera. Doing so may cause electric shock
and other hazards.
Any evidence of misuse, abuse, or tampering will void the Limited Warranty.
To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and
operated withminimum distance of 20 cm between the radiator and your body. Use only the enclosed
power adapter.
247-ES-CAM4A Quick Start Guide
Designed and Distributed by
247HelpAlert LLC
Irvine, California, USA
www.247HelpAlert.com