3D Systems Touch X User manual

Touch X
©2018 3D Systems Inc. All rights reserved. The 3D Systems logo and stylized text are registered trademarks of 3D Systems Inc.
All other trademarks are the property of their respective owners.
™
1
Download and Install drivers Remove device from packaging Connect and power up device
Run Touch Smart Setup Perform verication tests Save conguration
Download the Touch Device Driver from
www.3dsystems.com/haptics-devices/
touch-x/documents. Follow the Install
Wizard instructions to install the Touch
Device Drivers. Reboot your computer
after installing drivers to avoid any
performance issues.
Grab the polybag and remove the device
from the packaging. Lift the device out of
the foam by grasping the back and secur-
ing the rotating head as shown above.
DO NOT lift the device by grasping the
stylus or arm (this can damage the device).
Connect the power cord to the power sup-
ply and to an available outlet. Then plug in
the power supply to the device. The LED at
the top should quickly blink twice.
Connect the provided USB cable to both
the device and the host computer.
After connecting the device, run the
Touch Smart Setup application. To
calibrate the device, slowly move the arm
to the right and left, up and down, in and
out. Indicator boxes will turn green when
each axis is calibrated.
Perform the steps presented in the Sphere
Simulation and Hollow Cube Simulation
tests to verify proper device performance.
When these tests have been completed,
select Save Conguration to complete
the Touch Smart Setup process.
23
456
NOTE: Geomagic Freeform or Geomagic Sculpt cannot be open while running the Smart Setup.
Phone: [phone]
E-mail: Software[email protected]
Please refer to the 3D Systems Touch Device User Guide for installation, safety, and
proper operating and handling instructions. The User Guide can be found here:
www.3dsystems.com/haptics-devices/touch-x/documents
30-0432 Rev. A
Grip &
Lift
Secure
Joints
Arm
Stylus
To USB
Port
To Wall
Outlet
Connect
Power
Supply

System Requirements
Operating System 64-bit Windows 7, 8.1, and 10
Processor Intel i5 / i7, 5th Generation or greater CPU
Minimum 2.5 GHz frequency.
RAM 4 GB
Graphics Card Minimum 256 MB VRAM (Install the latest drivers).
Disk Space 512 MB
Display Resolution 1280 x 800 (Minimum)
Interface USB 2.0 / 3.0 port or USB Hub that supports USB 2.0/ 3.0.
(Use only USB A to B cable provided by 3D Systems).
Warranty
No warranties of any kind are created or extended by this publication. 3D Systems warrants that the Touch X haptic
device will be free from defects in materials and workmanship, during the applicable warranty period, when used
under the normal conditions described in the documentation provided to you, including the respective User Guide.
3D Systems will promptly repair or replace the Touch X, if required, to make it free of defects during the warranty
period. This warranty excludes repairs required during the warranty period because of abnormal use or conditions
(such as riots, oods, misuse, neglect or improper service by anyone except 3D Systems or its authorized service
provider). The warranty period for the Touch X is twelve (12) months and shall start the date your device was
purchased. For consumers who are covered by consumer protection laws or regulations in their country of purchase
or, if di󰀨erent, their country of residence, the benets conferred by our standard warranty are in addition to, and
operate concurrently with, all rights and remedies conveyed by such consumer protection laws and regulations,
including but not limited to these additional rights.
THIS WARRANTY IS THE ONLY WARRANTY PROVIDED FOR THE TOUCH DEVICE. TO THE MAXIMUM
EXTENT PERMITTED BY LAW, 3D SYSTEMS EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES FOR THE
TOUCH X DEVICE AND EACH OF ITS COMPONENTS, WHETHER THOSE WARRANTIES ARE EXPRESS,
IMPLIED OR STATUTORY, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR INTENDED
OR PARTICULAR PURPOSES.
©2018 3D Systems Inc. All rights reserved. The 3D Systems logo and stylized text are registered trademarks of 3D Systems Inc.
All other trademarks are the property of their respective owners. 30-0432 Rev. A
Touch X™