3M projectorsleeve User manual

User’s Manual
1
EN
Important Notice
All statements, technical information, and recommendations related to 3M's
products are based on information believed to be reliable, but the accuracy or
completeness is not guaranteed. Before using this product, you must evaluate it
and determine if it is suitable for your intended application. You assume all risks
and liability associated with such use. Any statements related to the product which
are not contained in 3M’s current publications, or any contrary statements
contained on your purchase order shall have no force or effect unless expressly
set forth in a written agreement signed by an authorized officer of 3M.
Technical Support
For technical support, call 1-866-631-1656 or email [e-mail]
© 3M 2012. All Rights Reserved.

User’s Manual
2
EN
Intended Use Statement
The 3M Projector Sleeve for iPhone 4/4S is designed to operate with the Apple®
iPhone 4 and iPhone 4S and charge using Apple USB power adapter or computer
USB port in environments that meet these conditions:
z5° to 35°C (41° to 95°F)
z20–80% RH (without condensation)
z0– 3048 m (0–10,000 feet) above sea level
Continued exposure to smoke, grease, oil and other airborne contaminants can
affect the operation or performance of the projector. Use of this product in adverse
conditions will void the product warranty.
Safety Information
Please read, understand, and follow all safety information contained in these
instructions prior to the use of this projector. Retain these instructions for future
reference.
Explanation of Signal Word Consequences
Warning: Indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury and/or
property damage.
Caution: Indicates a potentially hazardous situation, which, if not
avoided, may result in minor or moderate injury and/or
property damage.
© 3M 2012. All Rights Reserved.

User’s Manual
3
EN
Warning
To reduce the risk associated with hazardous voltage, fire, explosion, battery
leakage or overheating which may cause serious injury or death:
zDo not leave the product in a car or in direct sunlight for extended periods of
time. (-20 C to 70 C)
zDo not disassemble/ modify the product or attempt to remove the battery.
zDo not attempt to service this product. Contact manufacturer.
zDo not use the product in water or a damp environment.
zDo not use a damaged USB cable or Apple USB power adapter.
zCharge with only computer USB port or Apple USB power adapter.
To reduce the risks associated with driver distraction:
zDo not shine light into the driver's eyes.
zDriver should not operate product while driving.
To reduce the risks associated with choking:
zKeep the USB cable away from young children.
Caution
To reduce the risk associated with environmental disposal hazards which
may cause minor or moderate injury:
zDispose of the product and accessories in accordance with the federal, state,
local or regional laws which cover the disposal of electrical and electronic
waste.
To reduce the risks associated with projector LED bright light which may
cause minor or moderate injury:
zDo not look directly into the projector lens or shine it into anyone’s eyes
To reduce the risks associated with tripping and falling:
zPosition the USB cable so that it is not a tripping hazard.
© 3M 2012. All Rights Reserved.

User’s Manual
4
EN
To reduce the risk of muscle strain which if not avoided may cause minor or
moderate injury:
zDo not position the projector in awkward viewing positions.
SAVE THESE INSTRUCTIONS
Limited Warranty
This warranty applies to the continental US only. The warranty terms, conditions,
remedy and limitation may vary in other countries. Contact your local 3M Company
for warranty information.
The 3M™ Projector Sleeve (the “3M Product”) is warranted to be free from defects
in material or manufacture for a period of 1 year from the date or purchase. If the
product does not conform to the warranty within the warranty period, 3M’s
exclusive obligation is to repair, replace or refund the purchase price of the
non-conforming product. To the extent permitted by law, 3M will not be liable for
indirect, incidental, special or consequential damages, irrespective of the legal
theory asserted. If the product needs service, please call 1-866-631-1656. For the
detailed terms and conditions of the warranty go to
www.3mpocketprojector.com/support, or contact us at 1-866-631-1656 or
meeting[email protected].
FCC STATEMENT - CLASS B
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
© 3M 2012. All Rights Reserved.

User’s Manual
5
EN
zReorient or relocate the receiving antenna.
zIncrease the separation between the equipment and receiver.
zConnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
zConsult the dealer or an experienced radio/TV technician for help.
NOTICE: This Class B digital apparatus complies with Canadian ICES-003.
INSTRUCTIONS TO USERS: This equipment complies with the requirements of
FCC equipment provided that the following conditions are met. If the cables include
a EMI ferrite core, attach the ferrite core end of the cable to the projector. Use the
cables which are included with the projector or specified.
Note: Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
CE Statement
ElectroMagnectic Compatibility Statement: Meets 2004/108/EC
Directive
Low Voltage Directive: Meets 2006-95-EC Directive.
NOTICE: You can find the above appropriate certified regulatory marks in the
product projection by pressing power button for 10 seconds.
WEEE Statement
The following information is only for EU-members States: The mark
shown to the right is in compliance with Waste Electrical and
Electronic Equipment Directive 2002/96/EC (WEEE). The mark
indicates the requirement NOT to dispose the equipment as
unsorted municipal waste, but use the return and collection
systems according to local law.
© 3M 2012. All Rights Reserved.

User’s Manual
6
EN
RoHS Statement
Restriction of the Use of Certain Hazardous Substances in
Electrical and Electronic Equipment (known as "RoHS”),
2011/65/EU of the European Parliament and of the Council
and the Regulation 1907/2006 (known as “REACH”) relating
to “Substances of Very High Concern (“SVHC's”), the European Union’s Directive
94/62/EC relating to packaging, the U.S. Lacey Act and other similar laws
(“Substance Laws”). Product will not contain substances in excess of permitted
concentration values established by Substance Laws unless the applicable
specifications specifically permit that substance in a higher concentration value.
Without limiting the forgoing, substances in the product will not exceed the
following maximum concentration values in any homogeneous material
(“Restricted Values”): (a) 0.1% (by weight) for each of lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b)
0.01% (by weight) for cadmium.
Copyright, Trademarks and Properties Notices
3M and the 3M logo are trademarks of 3M Company. Used under license in
Canada. All other trade names referenced are the service marks, trademarks or
registered trademarks of their respective companies.
© 3M 2012. All Rights Reserved.

User’s Manual
7
EN
Product Overview
Scene mode Switch
iPhone Connector
Focus Wheel
Projector Lens
LED Indicato
r
iPhone
Charging Mode
Button
Micro USB
Charging Port
Power Button
Cinema mode: Enhance color
performance.
Web mode: Enhance text
performance.
Eco mode: Decrease brightness for
power saving.
© 3M 2012. All Rights Reserved.

User’s Manual
8
EN
Charging the Projector
Charge the projector by
connecting the projector to a
computer or an iPhone Power
Adapter using the USB cable
included with the projector.
NOTE:
i. The battery will take up to 4 hours to
charge.
ii. The Apple iPhone 4/4S Power
Adapter is not included with the
projector.
Charging for iPhone
1. Connect the iPhone to the
projector.
2. Press the iPhone charging
mode button to start or stop
charging for iPhone.
LED Indicator Modes
LED Status Indication
3 white LEDs stay on Power capacity is between 80% to 100%
2 white LEDs stay on Power capacity is between 45% to 80%
1 white LED stays on Power capacity is between 10% to 45%
1 white LED blinks Power capacity is below 10%
LED Marquee Product is being charged
LED blinks Charging for iPhone
1.
2.
or
1
1
2
© 3M 2012. All Rights Reserved.

User’s Manual
9
EN
Turning on/off the projector
Press the Power Button for 3
seconds to turn ON or turn OFF
the projector.
Adjusting the Focus
Adjust the focus by using the
focus wheel to get a sharper and
clear picture.
Projecting photos and videos via iPhone native app
1. Select the “Photos” icon on iPhone home screen.
2. Choose the photo or video you want to project.
* Photos can only be projected as a slideshow.
**Please push the volume control button on iPhone to adjust the
volume during playback.
© 3M 2012. All Rights Reserved.

User’s Manual
10
EN
Product specifications
Item Description
Optical Technology DLP
Light Source RGB LED
Resolution 640 x 480 Pixels (VGA)
Brightness Up to ANSI 35 lumens
Projection Image Size 254 mm ~ 1524 mm (10” ~ 60” Diagonal)
Operating System iOS4, iOS5
Projection Source iPhone 4, iPhone 4S
Power Input 5V / 1A
Power Output 5V / 1A
Battery Type Embedded 1850 mAh, Li-polymer
rechargeable battery
Battery Life Projection mode: 120 min (下行刪除)
Power Consumption Projection mode: 4.5W
iPhone charging mode: 5W
Operation
Temperature
5 °C ~ 35 °C
Dimension (LxWxH) 126 x 68 x 20 mm
Weight 125 g (4.4 oz)
Package Content Projector Sleeve, USB cable, Quick Start
Guide, and Product Safety Information
* All specifications are subject to change without notice.
© 3M 2012. All Rights Reserved.

User’s Manual
11
EN
Troubleshooting
Symptom Check Point
The projector will not turn on. Ensure the battery is fully charged.
The projected image is too
dark.
* Use the Projector in a darker
environment.
* Decrease the size of projecting
image.
The projected image is too
blurry.
Adjust the focus by using focus
wheel.
The projector is turned on, but
an image is not projected.
Ensure the App has a TV-out
function.
The temperature of the
projector’s surface is warm.
It is normal for this projector to
generate moderate heat during
normal operation.
When connecting the iPhone
to the projector and an error
message appears on iPhone
screen as shown below.
It may be caused by poor a
connection between iPhone and
the projector. Please reconnect
iPhone and projector, then turn on
the projector again.
© 3M 2012. All Rights Reserved.

User’s Manual
12
EN
Symptom Check Point
The projection image ratio is
distorted.
On the iPhone, switch the
Widescreen setting to "Off" in
Settings>Gerneral>TV out.
Stop video projection
suddenly and automatically.
On the iPhone, switch the Auto-lock
to "Never" in Settings>General.
Only safety logos and
numbers appear are on the
projection screen.
When the projector's power button
is held down for too long, the
projector enters engineering mode.
Press the power button until the
projector turns off, then press the
power button again for 3 seconds.
© 3M 2012. All Rights Reserved.

s Manual
Rev. A (10/2012) 78-6971-1633-9
© 3M 2012. All Rights Reserved.
Please Recycle.