3R Anyty 3R-VIEWTER-500UV User manual

Portable Digital Microscope Viewter
3R-VIEWTER-500UV（UV LED Model）
3R-VIEWTER-500IR（IR LED Model）
Operating Instruction

―1 ―
Index
1. Contents 2
2. Name of each parts 3
3. Set up
3.1 Charging 5
3.2 Insert SD card. 5
3.3 Loading lens cover and spacer 6
3.4 Adjust magnification and focal point 7
3.5 Connect Controller 8
4. Use ‘Viewter’
4.1 Power 9
4.2 Adjust magnification and focal point 9
4.3 Digital zoom 9
4.4 LED adjustment 10
4.5 Display scale 10
4.6 Capture still picture 11
4.7 Capture movie 12
4.8 Preview saved data 12
5. Settings
5.1 Setting of still mode 14
5.2 Setting of movie mode 15
5.3 Setting of preview mode and editing 16
5.4 Setting of Viewter 16
6. Software（VIEWTER Plus）
6.1 Install VIEWTER Plus 20
6.2 Preparation for using（Remove saved data）23
6.3 Use of VIEWTER Plus 26
7. Notes and Q&A 34
8. Spec 35
9. Cautions 36

―2 ―
1. Contents
The product contains items below. Please check package
※Description without spacer in some parts of this manual
Viewter Wired Controller Lens cover（x2）
Spacer（x2）USB charging cable miniUSB cable
AC/USB charging adaptor
Strap
Simple scale
Software CD（VIEWTER Plus）
SDHC Card 4GB（sample）
Cleaning cloth
Manual（This book）

―3 ―
2. Name of each sector
Name of each part below
●Viewter
Name
Function
①Power Button
Switch Viewter on/off
②Shutter Button
Button for capturing picture/movie
③Controller connector
Port for Wire controller
④Holder hock
Hock for strap
⑤Lens cover
Lens and lens cover for height adjustment
⑥Charging lamp
Red light during charge period
⑦LED dial
Dial for LED adjustment
⑧miniUSB port
For connecting to PC
⑨Charging connector
Port for charging Viewter
Continue to next page

―4 ―
Name
function
⑩Monitor
Display information
⑪Magnification Dial
Dial for adjusting magnification and focal point
⑫Lens cover
Lens cover for height adjusting
⑬SD/SDHC Slot
Slot for setting SD card
⑭LED button
Button for setting LED mode
⑮Menu button
Button for displaying setting menu
⑯Mode button
Button for switching mode
⑰Direction key
keys for setting menu.etc
⑱Confirmation button
Button for confirming options
⑲⑳Digital zoom
For adjusting digital zoom system
●Wire Controller（Approx 90cm long）
Each function of button on controller is same as each same name of button on scope.
Shutter button
Mode button
LED button

―5 ―
3. Set up
3.1 Charging
Please charge the ‘Viewter’ Microscope before use it. Use attached USB charging cable
and AC/USB adaptor to connect ‘Viewter’ to household wall outlet. Charging lamp will
be red during charging period. Charging time will be approx 4~5 hours. Charging lamp
will be blue when charging is complete.
※Please charge battery until full power before first use
※We do not recommend you use it and charge it at same time or it will shorten battery
life
3.2 Insert SD card
Images captured by Viewter will be saved in SD card. Please insert SD card into SD/SDHC
card slot as a image on next page. Maximum usable size of SD is 32GB.
※If you use MicroSD/SDHC card, please make sure that MicroSD/SDHC card
is set in adaptor correctly.
※If the card could not be read properly, please remove the card and set
it again.
Charging port
Charging lamp

―6 ―
3.3 Loading lens cover and spacer
Viewter contains 2 sets of lens covers and spacers.
●For x60 + x200
●For x80 + x150
Change lens cover and spacer to gain magnification you want. You could also
remove them when you could not gain magnification you want with them.
Pull this direction to remove

―7 ―
3.4 Adjust magnification and focal point
Please adjust magnification dial after loading lens cover and spacer as well
as for finer adjustment during capturing.
The image shows magnification and focal range below. Let the lens cover touch
the object you want to observe. If the object could not be touched, please
remove it when you observe.
Dial
Lens cover
Lens cover
Lens cover

―8 ―
3.5 Connect controller
Connect attached controller to Viewter when you want to use it stable. Please
connect controller to controller port on Viewter.
※Functions of controller
○Shutter
○Mode change
○LED change

―9 ―
4. Use Viewter
4.1 Power
Switch it on when it is ready. Press power button for 1 second and the monitor
will be activated. Follow the same way when you want to switch it off.
4.2 Adjust magnification and focal point
Get lens part (Lens cover) closed to object, the image of object will be
displayed on screen. Please use magnification dial to adjust magnification
and focal point.
4.3 Digital zoom
You could also use digital zoom function to adjust magnification.
Press 「＋ / －」 button to adjust magnification of digital zoom.
Maximum zooming sizex4
※Due to its feature, the image quality will deteriorate when you use digital
zoom function.
Power Button
Monitor
Dial
Digital zoom button（＋ －）

―10 ―
4.4 Adjust LED
The LED light is loaded on Viewter in order to adjust brightness of the object.
Press 「LED」button to switch LED mode (3 options). To adjust brightness,
please use LED dial on flank of Viewter（→Page 3）.
Light off→White LED→UV LED（IR LED）
4.5 Display scale
You are able to long press ‘OK’button during Still/Movie mode to display scale
on the scale. Use the scale to help match position and measure.
※The scale will only show on screen but not in saved data.
The scale will be
displayed on screen
OK button（Middle）
LED button（left side）

―11 ―
4.6 Capture still picture
Press the shutter button next to power button and screen will go dark. That
is the sign of capture
Mode of still is shown as below.
1
Mark of still mode
2
Shows space of SD card and savable number of pictures.
3
Icon of SD card. X Mark will be on it if the SD card is not loaded properly
4
Setting of resolution of saved pictures.
5
Residual amount of inner battery
6
Current date and time
Shutter button
OK button（Middle）

―12 ―
Shutter button
Mode button（Right side）
4.7 Capture movie
Please press Mode button to switch to movie mode and press shutter button
next to power button so the recording will be starting. Press shutter button
once again to finish recording.
Mode of movie is shown as below
4.8 Preview of captured data
Please press mode button twice to switch to preview mode. Then use direction
key (Left and Right) to select picture/movie. Press shutter button to play
saved movies.
1
Mark of movie mode
2
Shows space of SD card and savable times of pictures
3
Icon of SD card. X Mark will be on it if the SD card is not loaded properly
4
Setting of resolution of saved movie
5
Residual amount of inner battery
6
Current date and time

―13 ―
Mode of preview is shown as below
1
Mark of preview mode（Preview of still picture will be icon）
2
（Only for Movie）Play time of Movies
3
Icon of SD card. X Mark will be on it if the SD card is not loaded properly
4
Setting of resolution
5
Residual amount of inner battery
6
No. of being previewed data
7
（Movie only）Press shutter button to play movie
Shutter button
Mode button（Right side）
Direction key（LeftRight）

―14 ―
5. Settings
Explain check and change modes and settings in this section. Press menu
button in each mode to launch setting menu and use cross key (left, right)
to choose option. Then use cross key (up, down) to change settings.
5.1 Setting of still mode
Settings in still picture mode
※See 5.4 to enter main setting(→page 16)
Change color
You are able to change color of saving data
Change resolution
The second icon from left side is resolution setting icon. Please select
5 types of resolution from the list. Large number of resolution could
produce high quality of images but the size of file will be larger as well.
Normal
Default setting, full color
Gray Scale
Monochrome data
Menu button（middle）

―15 ―
Image stabilizing system
The third icon from left side is image stabilizing system icon. The system
might not work properly due to large shake
5.2 setting of movie mode
Settings during movie mode
White balance
An icon at left side is White balance setting
Change resolution
An icon at right side is movie resolution setting icon. Please select 2 types
of resolution from the list. Large number of resolution could produce high
quality of movies but the size of file will be larger as well
500M
Save data in 2060ｘ1920 pixel
300M
Save data in 2048ｘ1536 pixel
200M
Save data in 1600ｘ1200 pixel
100M
Save data in 1280ｘ960 pixel
VGA
Save data in 640ｘ480 pixel
On
Image stabilizing system on
Off
Image stabilizing system off
Normal
Normal white balance setting
Outdoor（Sunny）
Setting in the environment where the light is strong
Outdoor（Cloudy）
Setting in the environment where the light is weak
Incandescent lamp
Setting in the environment of incandescent lamp
Fluorescent lamp
Setting in the environment of fluorescent lamp
VGA
640ｘ480 pixel
QVGA
320ｘ240 pixel

―16 ―
5.3 Setting and editing of preview mode
Setting during preview mode
Turn of the image（Still picture only）
You are able to change direction of images during preview
File Protection
You are able to lock up the file you do not want to be deleted
Delete files
Delete selected file or all files
5.4 Main body setting
You are able to edit, set still picture and basic setting of Viewter.
Exposure
Adjust exposure between , , , , , ,
Adjust White balance
Adjust white balance of still picture
90°
Clockwise rotation 90°
180°
Clockwise rotation 180°
270°
Clockwise rotation 270°
Cancel
Terminate rotating system
Protect
Enable protection
Unlock
Disable protection
Current image
Delete current preview
All
Delete all data in the SD card
Cancel
Terminate Deletion

―17 ―
Sharpness
Image adjustment of still picture
Quality of saving picture
Setting quality of saved still picture.
Time stamp
Inserting Time stamp into saved data and setting time and date of time stamp
Normal
Default setting
Outdoor（Sunny）
Setting in the environment where the light is strong
Outdoor（Cloudy）
Setting in the environment where the light is weak
Incandescent lamp
Setting in the environment of incandescent lamp
Fluorescent lamp
Setting in the environment of fluorescent lamp
Normal
Default setting
Sharp
Large change of color and brightness of the picture
Soft
Soft change of color and brightness of the picture
Super fine
The highest quality of the picture
Fine
Default setting
Normal
The Smallest size of file
On
Enable time stamp
Off
Disable time stamp
Time setting
Adjust time of time stamp
Another screen will show so you could set it there

―18 ―
Auto power off
Power will be off automatically if no operation after times below;
Language
You are able to select display language of Viewter.
Frequency
※Normally you do not need to adjust it
Format
Formatting data in SD card
Default
Reset all setting
1min
Set auto power off time in 1min
3mins
Set auto power off time in 3mins
5mins
Set auto power off time in 5mins
Off
Disable auto power off system
OK
Start Formatting
Cancel
Terminate formatting option
OK
Confirm defaulting
Cancel
Terminate Default option

―19 ―
6. Software（VIEWTER Plus）
You could use the attached software ‘VIEWER Plus’to edit and measure saved data. Please read the
information about Installation requirement below
★Minimum requirement
OS※Windows8,7（32bit / 64bit）
WindowsXPSP3、Vista (32bit Version only)
CPU Pentium Ⅲ1Ghz or higher spec of CPU
Optical drive required
Memory above 256MB
Space requirement above 1000MB
Connection type USB1.1/2.0
Display space 15 Inches（XGA）or more
Graphic 16bit color or above
Operation authorization Administrator privileges might be needed during installation
★Recommended environment
CPU Pentium 4 1.6Ghz or above
Memory 512MB or more
Saving space 10GB or more
Display space 17 inches（SXGA）or above
Graphic card 16bit color, Video memory 64MB or more