3rd eye Mobilevision awt07mled User manual

Thank you for purchasing our product.

Please read this User’s Manual before

using the product.

Change without Notice

AWT07MLED

7” Q TFT LCD MONITOR (LED Backlighted)

USER MANUAL

-4

Federal Communications Commission (FCC) Statement

This Equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

-Consult the dealer or an experienced radio / TV technician for help.

zYou are cautioned that changes or modifications not expressly approved by

the party responsible for compliance could void your authority to operate the

equipment.

SAFETY PRECAUTIONS

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference and,

(2) This device must accept any interference received, including interference

that may cause undesired operation

Safety Precaution.………………………....…………………………………………..........2

Table of Content.….………………………………………………………………………3

Features….………………………………………………………………………………...4

1. Package Contents…….………………………………………………………………..5

2. TFT Installation……………………………………………….…………………………6

3. Signal Cable Description……..………………………………….…………………..7

4. Control Cable Description……..…………………………………….……………….9

5. Front Panel Control.……………………………………………………..………… 10

Main OSD Menu…….........……………………………………………….………11

Screen Menu……………………………………………………………………...12

Display ……….…………………………………………………………….…13

Camera ...……………………………….…………..................................15

Information...……………………………….…………..................................19

6. Vehicle Installation ……………………………………….……………………..20

7. Specification…..………………………………………..……………………….21

8. Attachment…..……………………………………………….……………………22

TABLE OF CONTENT

zAdvanced OSD Menu for easy use

zSupport up to 4 CCD Camera inputs (Mini din connector)

zExtra RCA input for multimedia while parking (VCD, DVD, Game device)

zProvide 2 Video / 1 Audio Signal Output (Live Out)

zSupport Single / Dual / Triple / Quad Screen (Cam Out)

zSignal Trigger for Side / Rear View

zAuto Day & Night Control via Photo Diode Sensor

zAuto Detection for NTSC / PAL System

zOSD Control for Individual Normal / Mirror Camera Image for every camera

zAuto power on when users are making left turn or right turn even reverse

zAble to select CAM A / B/C / R’s monitoring screen

zSupported 9.6V~32V Car power system working

zProfessional Metal Case with Anti Shocking Design

FEATURE

Item Qty.

1. 7” LCD Monitor 1

2. Sun-Hood 1

3. Mounting Bracket 1

4. Accessories 1

5. Control Cable 1

6. User Manual 1

1. Package Contents

Step 1

Check the package and make sure all parts are included.

Step 2

Clip the sun-hood on to the monitor.

Step 3

Make sure it is installed properly.

Step 4

Install the monitor on to the bracket.

Step 5

Adjust the monitor to an appropriate / comfortable viewing

angle before tightening the screws.

Step 6

Connect the control cable included to the power socket

which located at rear side of monitor.

Step 7

Monitor installation is now completed. Each control cable

wire is attached with a sticker to indicate its signal function.

Referred to the identification sticker for further installation.

2. TFT Installation

1. CAM R (Mini din) (NTSC/PAL system presume by this car rear CCD)

For 1st camera connection

2. CAM A (Mini din)

For 2nd camera connection

3. CAM B (Mini din)

For 3rd camera connection

4. CAM C (Mini din)

For 4th camera connection

5. LIVE VIDEO OUT (White Color RCA Jack)

On screen video loop out (for recording, second monitor or other device)

6. LIVE AUDIO OUT (Black Color RCA Jack)

On screen audio loop out (for recording, second monitor or other device)

7. AV VIDEO IN (Yellow Color RCA Jack)

Connection for any Video signal (DVD, VCD, Game)

8. AV AUDIO IN (Red Color RCA Jack)

Connection for any Audio signal (such as DVD, VCD, Game)

9. CAM OUT (Green Color RCA Jack)

Video loop out (for recording, second monitor or other device)

3. Signal Cable Description

Function of the Audio

※ Cam Out: Composite video loop out signal to recorder, monitor or other device.

※ Live Video/Audio Out: On screen video/audio signal loop out to recorder, monitor

or other device.

Cam A Audio from Cam A

Cam B Audio from Cam B

Cam C Audio from Cam C

Cam R Audio from Cam R

Cam A + Cam B Audio from Cam A

Cam C+ Cam R Audio from Cam R

Cam A+ Cam R Audio from Cam R

Cam R+ Cam B Audio from Cam R

Cam A + Cam C Audio from Cam A

Cam C+ Cam B Audio from Cam C

Cam R / Cam AB Audio from Cam R

Quad Audio from Cam R

AV Audio from AV

Mini Din Pin Assignment * Type 1 (Standard):

1. Video 4. +12V

2. ------- 5. GND

3. Audio 6. -------

1. The control cable sequence: Reverse > Right / Left / CAM C when Priority is ON. Right

/ Left / CAM C > Reverse when Priority is OFF.

2. With car power is on, the monitor power is off, when making a reverse / right / left turn,

the monitor will display default screen.

3. You may push the “JUMP” button under event trigger when Priority is OFF.

WIRE COLOR FUNCTION REMARK ON SCREEN VIEW

RED ACC POWER

BLACK GND

WHITE SW Control Active Power

Level Connect to

CAM C

BLUE Reverse Control Active Power

Level Connect to

Reverse Light

ORANGE Right Turn Control Active Power

Level Connect to

Direction Light

(R)

YELLOW Left Turn Control Active Power

Level Connect to

Direction Light

(L)

4. Control cable Description

Don’t connect the red wire (power wire) of this produc

directly to the battery. Connect the red wire of this produc

to the ACC of the ignition key switch. Failure to do so ma

result in permanent damage of the product.

Jum p Source P o wer

M enu

CAMR

CAM R CAM B

CAMA CAM R

POWER Press the power button to activate the monitor or to keep the monitor

under stand by mode (In Red Led).

SELECT With power on, press this button to select image sequence as below~

AVÆCAM A+BÆCAM C+RÆCAM A+RÆCAM R+BÆCAM A+CÆ

CAM C+BÆCAM R/ABÆCAM R+ABÆCAM AÆCAM BÆCAM CÆ

CAM R ÆAV……..

Prerequisite：Display menu ÆPriority option is “ON”

JUMP Press this button to display defined camera input, user can select

QUADÆSEQÆCAM A+BÆCAM C+RÆCAM A+RÆCAM R+BÆ

CAM A+CÆCAM C+BÆCAM R/AB ÆCAM R+AB ÆCAM A ÆCAM B

CAM CÆCAM R via OSD as default value.

Prerequisite：Display menu ÆPriority option is “ON”

MENU This encoder switch provides the following function:

1. Activate OSD menu: Press the Menu switch to activate the OSD menu.

After the OSD menu is activated, in case users does not proceed for

further set up, the OSD menu will then automatically turn off within

20 seconds.

2. Enter Function: Press the encoder switch to act as “Enter” function

under the OSD menu.

3. Volume Value: Exit the OSD menu, user can turn this switch

left or right to adjust the volume value.

5. Front Panel Control

OSD Menu

1. Press the MENU button to enter to the OSD Menu

2. Turn the MENU button left or right to select the setting you

wish to proceed. The color of the content will turns YELLOW

to identify your selection. Turn the MENU button left or right to

adjust your setting value.

3. Press the MENU button once back to submenu and then press menu

button again in order to return to OSD menu.

Enter to Main menu:

SCREEN Menu

This menu set up contains different setting for the TFT LCD.

Brightness

Provide adjustment for shade and brightness level of TFT display.

Setting value from 0 ~ 100. Default value is 37.

Contrast

Provide adjustment for the light and dark level of the TFT display.

Setting value from 0 ~ 100. Default value is 50.

Saturation

Provide adjustment for the light intensity level of TFT display.

Setting value from 0 ~ 100. Default value is 40.

Hue

Provide adjustment for the lightness and colorfulness level of TFT display.

Setting value from 0 ~ 100. Default value is 45.

(Only in NTSC system is available.)

Sharpness

Provide adjustment for the edge contrast (acutance) level of TFT display.

Setting value from 0 ~ 100. Default value is 100.

Return

Return to OSD menu selection screen.

DISPLAYMenu

This menu set up contains the on screen identification

and the activation of the distance gauge.

Auto Day&Night

Select “ON” to activate the auto day & night function or “OFF” to

deactivate it. Default value is OFF.

Display

Select “ON” to show the SELECT of video input title on screen or “OFF”

to keep it invisible. Default value is ON.

Distance Gauge

Set the distance gauge “ON” to show the distance gauge on screen while

reserving or “OFF” to deactivate. Default value is ON.

(This “DISTANCE GAUGE” is for user’s reference only)

OSD Lock

This function provides protection when an unauthorized person tries to

access the OSD settings. JUMP and SELECT key press simultaneously

for over 5 seconds to unlock. Default value is OFF.

※Users must turn on LCD in order to run unlock process. All function

buttons are still working during OSD Menu lock up period.

PRIORITY

If Priority is ON

a. Press SOURCE button to select image sequence as below~

AVÆCAM A+BÆCAM C+RÆCAM A+RÆCAM R+BÆCAM A+CÆ

CAM C+BÆCAM R/ABÆCAM R+ABÆCAM AÆCAM BÆCAM CÆ

CAM R ÆAV…….

b. Triggered mode priority: Reverse > Right/Left / CAM C

c. JUMP mode: QUAD

d. OSD Lock mode: OFF

If Priority is OFF

a. Press SOURCE button to select image sequence is as below~

AVÆCAM AÆCAM BÆCAM CÆCAM R ÆAV……..

b. Triggered mode priority: Right/Left/CAM C > Reverse

c. JUMP mode: CAM R

d. OSD Lock mode: ON

Default value is “ON”.

Notice：When you choose “OFF” mode also enable OSD Lock function.

REVERSE MODE

When reversing select LCD profile ratio 4:3 the display show in size

4:3(default), select LCD profile ratio 16:9 the display show in size 16:9

Return

Return to OSD menu selection screen.

CAMERAMenu

This menu set up contains the on Camera and Jump setting.

Mirror

Select “ON” to activate the mirror function for different cameras or

“OFF” for a normal image. Default values are following below setting.

CAM A “OFF”

CAM B “OFF”

CAM C “OFF”

CAM R “ON”

Dir Image

The screen image setting of this panel during left / right turn:

TRIPLE: When you are making a right turn or left turn, the screen of

panel will display triple images for left hand side, right

hand side and rear view when you are making a right turn

or left turn.

DUAL: With proper wiring, the screen will display dual image for

both rear and right hand side view when making a right turn.

While left turning, the screen will show dual image for both

rear and left hand side view.

SINGLE: Screen of touch panel shows only single picture on direction

turn. The screen will show only left side view on left turn and

only right side view on right turn.

Default value is SINGLE.

Rear Setup

The screen image setting of this panel during reverse gear:

R: Screen will display single image for Cam R only.

R+A: Screen will display dual image for both Cam R and Cam A.

R+B: Screen will display dual image for both Cam R and Cam B.

R/AB Screen will display triple image from Cam R、Cam A、Cam B.

R+AB Screen will display triple image from Cam R、Cam A、Cam B.

Default value is R.

CAM R CAM B

CAMA

CAMR

CAMBCAMA

Jump

By pressing this button, the driver will be able to obtain the image

selected under this setting.

QUAD Obtain image from all camera input in quad picture

while pressing the JUMP button and press again to

return the default screen.

SEQ. Corresponding with “SEQ. Timer Step” setting to

jump channel by time sequence.

CAM A Obtain image from camera A while pressing the

JUMP button and press again to return the default

screen.

CAM B Obtain image from camera B while pressing the

JUMP button and press again to return the default

screen.

CAM C Obtain image from camera C while pressing the

JUMP button and press again to return the default

screen.

CAM R Obtain image from camera R while pressing the

JUMP button and press again to return the default

screen.

CAM A+B Obtain image from camera A+B in dual picture while