A.H. Systems AK-7G User manual

A.H. Systems AK-7G Antenna Kit
A.H. Systems inc. – January 2005
REV A 1
AK-7G
Antenna Kit
Operation Manual

A.H. Systems AK-7G Antenna Kit
A.H. Systems inc. – January 2005
REV A 2
TABLE OF CONTENTS
WARRANTY
3
INTRODUCTION 4
GENERAL INFORMATION 5
OPTIONAL EQUIPMENT 7
FORMULAS 8
MAINTENANCE 9

A.H. Systems AK-7G Antenna Kit
A.H. Systems inc. – January 2005
REV A 3
WARRANTY INFORMATION
A.H. Systems Inc., warrants that our Antennas, Sensors and Probes will be free from
defects in materials and workmanship for a period of three (3) years. All other products
delivered under contract will be warranted for a period of two (2) years. A.H. Systems'
obligation under this warranty shall be limited to repairing or replacing, F.O.B.
Chatsworth, California, each part of the product which is defective, provided that the
buyer gives A.H. Systems notice of such defect within the warranty period commencing
with the delivery of the product by A.H. Systems.
The remedy set forth herein shall be the only remedy available to the buyer, and in no
event shall A.H. Systems be liable for direct, indirect, incidental or consequential
damages.
This warranty shall not apply to any part of the product which, without fault of A.H.
Systems has been subject to alteration, failure caused by a part not supplied by A.H.
Systems, accident, fire or other casualty, negligence, misuse or normal wear of
materials.
Except for the warranty set forth above, there are no other warranties, expressed or
implied, with respect to the condition of the product or it's suitability for the use intended
for them by the buyer.
For prompt service, please contact our service department for a Return Material
Authorization Number before shipping equipment back to us.

A.H. Systems AK-7G Antenna Kit
A.H. Systems inc. – January 2005
REV A 4
INTRODUCTION
Shown: AK-18G
SPECIFICATIONS
Model Number Frequency Range Antenna Factor (dB/m)
SAS-510-7 290 MHz – 7000 MHz 15 to 47
SAS-530,542 20 MHz – 500 MHz 8 to 27
SAS-550-1B 9 KHz – 60 MHz -1 to 3
SAS-560 20 Hz – 2 MHz 18 to 15
Transfer Impedance
BCP-510 20 Hz – 1 MHz -40 to –30
BCP-511 20 KHz – 100 MHz -1 to 1
Attenuation
SAC-211 Up to 10 GHz 4.4 dB @ 10 GHz
OPTIONAL EQUIPMENT
Gain / Attenuation
PAM-0207 20 MHz – 7 GHz 30 dB

A.H. Systems AK-7G Antenna Kit
A.H. Systems inc. – January 2005
REV A 5
GENERAL INFORMATION
INTENDED PURPOSES
This equipment is intended for general laboratory use in a wide variety of industrial
and scientific applications, and designed to be used in the process of generating,
controlling and measuring high levels of electromagnetic Radio Frequency (RF)
energy. It is the responsibility of the user to assure that the device is operated in a
location which will control the radiated energy such that it will not cause injury and
will not violate regulatory levels of electromagnetic interference.
GENERAL DESCRIPTION
The A.H. Systems AK-7G antenna kit series consist of five E-field antennas, one
magnetic loop antenna, and two current probes. Each of the antennas and probes
are provided with calibrations when connected to a 50 ohm input receiver or
spectrum analyzer.
Each of the E-field antennas mount directly to the tripod azimuth and elevation
head. The azimuth and elevation head allows the operator to vary the antenna
azimuth (direction) and to change the antenna polarity (vertical or horizontal).
Cables and an adapter are provided to connect each antenna and probe to either
a BNC or N type connector on the receiver. Cable calibrations are supplied.
To obtain the field strength of the signal being measured, the operator must add
the receiver reading in dBuV, the antenna factor in dB, and the cable attenuation in
dB. This yields the field strength in dBuV/m. Calibrations for the E-field antennas
are supplied at appropriate spacings (1, 3, and 10 meter) to comply with various
specification requirements.
E-FIELD ANTENNAS
SAS-510-7 Log Periodic Antenna 290 MHz - 7000 MHz
The log periodic antenna comes assembled and ready to use.
Operation: Attach the antenna to the tripod azimuth and elevation head through
the screw hole in the antenna base. Connect a cable between the antenna
connector and the receiver. The log periodic beamwidth is 65 degrees and it
should be pointed or aimed in the direction that the received signal is coming from.
SAS-530,542 Broadband Dipole Antenna 160 MHz - 500 MHz
The broadband dipole antenna consists of the SAS-530,542 balun assembly and
two dipole (2" tubular) elements.
Operation: Attach the balun assembly to the tripod through the screw hole in
balun assembly base. Screw the two dipole elements into the 'tee' end of the balun

A.H. Systems AK-7G Antenna Kit
A.H. Systems inc. – January 2005
REV A 6
assembly. Connect a cable between the antenna connector and the receiver. The
broadband dipole beam pattern is similar to a dipole response.
SAS-530,542 Biconical Antenna 20 MHz - 330 MHz
The biconical antenna consists of the SAS-530,542 balun assembly and two
folding biconical elements.
Operation: Attach the balun assembly to the tripod thru the screw hole in the
balun assembly base. Screw the two biconical elements into the 'tee' end of the
balun assembly. Open the antenna elements completely and secure in open
position by tightening the knurled knobs in the element caps. Connect a cable
between the antenna connector and the receiver. The biconical beam pattern is
similar to a dipole response.
SAS-550-1B Active Monopole Antenna 10kHz - 60 MHz
The active monopole antenna consists of a ground plane upon which are mounted
a preamplifier with internal rechargeable battery pack for battery operation, and a
telescoping rod antenna.
Operation: Mount the antenna on the tripod. Connect an external ground to the
ground plane if called out in test specification. Attach the telescoping rod to the
connector on the amplifier top and extend fully. Connect the output on amplifier
side to the receiver using a cable. Apply power to antenna (turn battery power 'on'.
The active monopole antenna is omni-directional.
MAGNETIC LOOP ANTENNA
SAS-560 Magnetic Loop Antenna 20 Hz - 2 MHz
The loop antenna does not require any assembly.
Operation: The loop antenna is designed to be held by hand and moved around
each surface if the EUT to measure magnetic radiation. Connect the antenna via a
cable to a receiver with either a 50 ohm input or high impedance (10 K ohm or
greater) input. Calibrations for both inputs are provided.
CURRENT PROBES
BCP-510 LF Current Probe 20 Hz - 1 MHz
BCP-511 HF/VHF Current Probe 100 kHz - 100 MHz
The current probes come ready for use.
Operation: The two current probes measure conducted emissions when clamped
around a single conductor, cable or a bundle of conductors. Disconnect the probe
latch Position the probe around the conductor and close the probe. Reconnect the
probe latch to ensure that the probe is tightly closed. Connect the probe connector
to the receiver with a cable. The probe calibrations supplied are into a 50-ohm
receiver.

A.H. Systems AK-7G Antenna Kit
A.H. Systems inc. – January 2005
REV A 7
TRIPOD AND MOUNTING ADPTERS
ATU-510 Tripod
AEH-510 Azimuth and Elevation Head
The azimuth and elevation head (AEH-510) mounts to the tripod (ATU-510) top
and allows the antennas to be rotated 360 degrees and tilted between horizontal
and vertical polarization. The tripod and azimuth and elevation head come in their
own carrying case. Each tripod leg is independently adjustable in angle and length
to facilitate antenna height setting. The tripod legs have a rubber tip on one end for
indoor or hard surface use, and a metal spike on the other end for outdoor soft
surface (such as dirt) use.
TRANSIT STORAGE CASES
TCC-510 Tripod Carrying Case
TSC-542 Transit Storage Case
The antenna carrying case (TSC-542) prevents damage and loss of antennas
when storing or transporting the antenna kit. The case is constructed of lightweight
and durable polyethylene. Two case keys are provided with the case.
OPTIONAL EQUIPMENT
The AK-7G case comes with three additional cutouts for optional preamplifiers.
In order to improve overall system sensitivity, the following equipment will be
required:
 PAM-0207 with an SAC-211-0.5
PAM-0207 Preamplifier 20 MHz – 7 GHz
The preamplifier will increase the system sensitivity 30 dB and is recommend for
the SAS-510-7 and SAS-530,542. An optional short length cable (SAC-211-0.5), is
required to connect the preamplifier to any 50-ohm receiver or spectrum analyzer.

A.H. Systems AK-7G Antenna Kit
A.H. Systems inc. – January 2005
REV A 8
ANTENNA FORMULAS AND CALCULATIONS
E-FIELD ANTENNAS
Add antenna factor plus cable loss to receiver reading in dBuV to convert to field
strength in dBuV/meter.
Field Strength(dBuV/m) = SA(dBuV) + AF(dB) + cable loss (dB)
LOOP ANTENNA
dBpT = dBuV + dBpT/uV + Cable Loss
dBuV/m = dBpT + 49.5 dB
BROADBAND CURRENT PROBES
A specific Transfer Impedance Factor is associated with each frequency. This number is
to be subtracted from the receiver reading in order to convert to dBuA
dBA = dBV (from Receiver) - Transfer Impedance (dB) - cable Loss (dB)
EXAMPLE:
Assume that the frequency of interest is 80 KHz and we need to find the current at this
frequency. Connect the probe per figure 1
Frequency: 80 KHz
Transfer Impedance: -2.76 dB ohms
Cable Loss: 0.1dB
Receiver Reading: -33.0dBuV
dBA = dBV (from Receiver) - Transfer Impedance (dB) - cable Loss (dB)
dBA= -33.0 - (-2.76) - - 0.1
dBA= -30.14

A.H. Systems AK-7G Antenna Kit
A.H. Systems inc. – January 2005
REV A 9
MAINTENANCE
To ensure reliable and repeatable long-term performance, annual
re-calibration of your antennas, preamplifiers and current probes
by A.H. Systems experienced technicians is recommended. Our
staff can calibrate almost any type or brand of antenna.
For more information about our calibration services or to place an
order for antenna calibration visit our website at
http://www.AHSystems.com or call 1(818) 998-0223.