A-Neuvideo ANI-QUAD-LITE-4K User manual

AUDIO / VIDEO MANUFACTURER
ANI-QUAD-LITE-4K
4x1 HDMI Quad Multi-Viewer w/ Seamless Switcher
INSTRUCTION MANUAL
A-NeuVideo.com
Frisco, Texas 75036

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

TABLE OF CONTENTS
ANEUVIDEO
1
CONTENTS
INTRODUCTION & PACKAGE CONTENTS ...............................1
FEATURES & SPECIFICATIONS ................................................ 2
OPERATION & FUNCTIONS ........................................................ 3
REMOTE CONTROL .................................................................. 4
DISPLAY MODES ........................................................................ 5
APPLICATION EXAMPLE .......................................................... 6
Dear Customer
Thank you for purchasing this product. For optimum performance
and safety, please read these instructions carefully before
connecting, operating or adjusting this product. Please keep this
manual for future reference.
INTRODUCTION
The high performance 4x1 quad multi-viewer supports (4) HDMI
high denition inputs to be displayed on (1) HDMI screen and (1)
VGA screen simultaneously. It supports analog audio output that
can be selected between different input sources. Supports (5)
multi-view display modes. Output resolution can be adjusted and
supports the maximum up to 4K30Hz. The product can be controlled
via the front panel button and remote control. This product has a 3
year warranty.
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and
make sure the following items are contained in the shipping carton:
• ANI-QUAD-LITE-4K HDMI 4x1 Quad Multi-viewer
• 12V/1A DC Power Adapter
• Remote Control
• (2) Mounting Ears
• Users Guide
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without the express written permission and consent.
© Copyright 2019. All Rights Reserved.
Version 1.3 FEB 2019
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

2
FEATURES & SPECIFICATIONS
FEATURES
• HDMI 1.4b, HDCP 1.4 compliant
• Automatic Input resolution recognition. (480p~4K30Hz, 800x600~4K30Hz)
• Output resolution can be selected by front-panel button and remote control.
• HDMI supports resolution the maximum up to 4K30Hz. (3840x2160@30Hz, 1920x1080@50/60Hz, 1280x720@50/60Hz,
1920x1200@60Hz, 1024x768@60Hz)
• VGA supports resolution the maximum up to 1920x1200@60Hz. (1920x1080@50/60Hz,1280x720@50/60Hz,1920x1200@60Hz,10
24x768@60Hz) Note: If output resolution selects the 4K30Hz, the VGA port will be disabled.
• Audio supports LPCM 2CH.
• Supports 1/2/4 windows multi-view modes.
• Control is via on-panel button and remote control.
SPECIFICATIONS
• HDMI Compliance: HDMI 1.4b
• HDCP Compliance: HDCP 1.4
• Video Bandwidth: 10.2Gbps
• Video Resolutions: 3840x2160@30Hz,1920x1080@50/60Hz,1280x720@50/60Hz,1920x1200@60Hz,1024x768@60Hz
• Color Depth: 8-bit
• Color Space: RGB, YCbCr 4:4:4, YCbCr 4:2:2
• Analog Audio Formats: LPCM2.0 44.1KHz 48KHz
• ESD Protection: Human-body Model:
• ±8kV (Air-gap discharge)
• ±4kV (Contact discharge)
• Inputs Ports:
• (4) HDMI Type A [19-pin female]
• (1) SEVICER [Micro USB, Update port]
• Outputs Ports:
• HDMI Type A [19-pin female]
• VGA [VGA-D]
• Audio [3.5mm Stereo Mini-jack]
• Housing: Metal Enclosure
• Color: Black
• Dimensions (WxDxH): 7.3 x 5 x .8 in (185x128x20mm)
• Weight: 1.3 lb/595g
• Power Supply: Input: AC100~240V 50/60Hz, Output: DC12V/1A (US/EU standards, CE/FCC/UL certied)
• Power Consumption: 7.68W (max)
• Operating Temperature: 0°C ~ 40°C / 32°F ~ 104°F
• Storage Temperature:-20°C ~ 60°C / -4°F ~ 140°F
• Relative Humidity: 20~90% RH (non-condensing)
As product improvements are continuous, specications are subject to change without notice.
ANEUVIDEO

3
OPERATION & FUNCTIONS
FRONT PANEL
qPOWER LED: The LED will illuminate green when the unit is working, red when the unit is in standby mode.
wIR: IR receiver window. It accepts the remote control signal of this device only.
eCH1/CH2/CH3/CH4 BUTTON: Selects input channel (Please see “Display Modes” detail description).
rMODE BUTTON: Press this button to cycle thru output selection display mode (Please see “Display Modes” detail description). Press
this button 5 times until the output screen is full screen and equal proportion display.
tRESO: Cycle to select different output resolutions. Press this button 5 times to open or close the window display frame.
ySERVICE PORT: Firmware update only. (Does not control device.)
BACK PANEL
qHDMI INPUT: Connect to HDMI source device such as DVD player or PS4.
wHDMI OUTPUT: Connect to HDMI display device such as TV or Projector with a HDMI cable.
eVGA OUTPUT: VGA output port, this port output signal is the same as the HDMI output port.
rAUDIO OUTPUT: Analog audio output port. (Note: If the HDMI output is MODE 1, the audio output follows the video content. If the
HDMI output is MODE 2/3/4/5, press CH1/CH2/CH3/CH4 up to 5 times to select the audio output or use the remote control to cycle to the
audio output. The default status is CH1 screen audio output.)
tDC 12V: Plug the 12V/1A DC power supply into the unit and connected the adapter to an AC outlet.
ANEUVIDEO

4
Remote Control
Remote Control
qPOWER BUTTON: Press this button to cycle between ON and STAND-BY.
wOSD BUTTON: Press this button to cycle thru the OSD display. (Border, No Border, Input
Resolution).
eRES BUTTON: Press this button to cycle thru output resolutions.
rMODE BUTTONS: Press these buttons to select the output display mode.
tMODE CYCLE: Press this button to cycle thru all the display modes.
ySOURCE 1/2/3/4 BUTTONS:
WHEN IN MODE 1: Press any channel button to directly select that input source.
WHEN IN MODES 2-5: Repeatedly pressing any channel button will cycle thru all (4) sources
for that selected screen location only.
EXAMPLE 1: EXAMPLE 2:
Pressing the 1cycles thru
SOURCE 1-4
uINPUT SOURCE CYCLE: Press this button to cycle thru the input sources. (This button can
be used only in MODE 1.)
iMUTE: Mute button.
oAUDIO INPUT CYCLE: Press this button to select between (cycle) the (4) audio sources. (This button only works when in MODES 2-5.)
IR commands
NEC code
SYSTEM CODE: 00FF
POWER: 00 SOURCE3: 12
OSD: 01 SOURCE4: 14
RESOLUTION: 02 SOURCE_CYCLE: 16
MODE1: 04 AUDIO_ON/OFF: 18
MODE2: 05 AUDIO_CYCLE: 1A
MODE3: 06 AUDIO_IN1: 1B
MODE4: 08 AUDIO_IN2: 17
MODE5: 09 AUDIO_IN3: 1D
MODE_CYCLE: 0A AUDIO_IN4: 1E
SOURCE1: 10 RESET: 14
SOURCE2: 11
ANEUVIDEO
1
1
2
34
2
3
4
Pressing the 3cycles thru
SOURCE 1-4

5
Display Modes
Display Modes
The quad multi-viewer has 5 display modes. Please see the below detail description.
MODE 1: The quad multi-viewer will display separately four HDMI inputs. Press the CH1/CH2/CH3/CH4 buttons on-panel or using IR
remote control the Source 1/2/3/4 buttons to selecting input source, corresponding on-panel light is on.
MODE 2: The quad multi-viewer divides four HD inputs with same size and display on a screen. The on-panel four lights is on. In the CH1
window, you can press the CH1 button on-panel or using IR remote control the Source 1 button to cyclical selection four inputs source. In
the CH2 window, you can press the CH2 button on-panel or using IR remote control the Source 2 button to cyclical selection four inputs
source...etc. The rest can be done in the same manner.
MODE 3: The quad multi-viewer divides four HD inputs and display on a screen. The on-panel four lights is on. Operation method is the
same as MODE 2.
MODE 4: The quad multi-viewer divides two HD inputs with same size and display on a screen. The on-panel CH1/CH2 lights is on. In
the CH1 window, you can press the CH1 button on-panel or using IR remote control the Source 1 button to cyclical selection four inputs
source. On the CH2 window, you can press the CH2 button on-panel or using IR remote control the Source 2 button to cyclical selection
four inputs source.
MODE 5: The quad multi-viewer divides four HD inputs and display on a screen. The on-panel four lights is on. Operation method is the
same as MODE 2.
ANEUVIDEO

6
Application Example
Application Example
ANEUVIDEO

THIS PAGE IS INTENTIONALLY LEFT BLANK.

THIS PAGE IS INTENTIONALLY LEFT BLANK.

THIS PAGE IS INTENTIONALLY LEFT BLANK.

END OF DOCUMENT
10
TERMS & CONDITIONS OF USE
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED
BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at
the return address set forth on the Product’s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice
to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any
warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be
borne by you and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are
licensed to you by A-NeuVideo, Inc. and/or its afliates, including any manufacturers or distributors of the Product (collectively, “A-NeuVideo”) for your personal use
only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only.
A-NeuVideo does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual
property rights therein. All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any
manner without the prior written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVideo.
The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its ofces within the State of Texas, United States of America. A-NeuVideo
makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided
with respect thereto. You are advised that the Product may be subject to U.S. export controls.
DISCLAIMERS AND LIMITATION OF LIABILITY
A-NeuVideo may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR
MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be
relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies
or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
A-NEUVIDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT
TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL
NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY
A-NEUVIDEO.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FORANY SPECIALOR CONSEQUENTIAL
DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF
A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL
LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU
PAID TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT.
ANEUVIDEO