Aaeon FWS-7600 User manual

Network Appliance
FWS-7600
FWS-7600
1U Rackmount
Network Appliance Platform
1 ATA-100, 2 SATA II
6 USB Ports, Mini PCI
FWS-7600 Manual 3rd Ed.
April 30, 2014

Network Appliance
FWS-7600
i
Copyright Notice
This document is copyrighted, 2014. All rights are reserved. The
original manufacturer reserves the right to make improvements to the
products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original
manufacturer assumes no responsibility for its use, or for any in-
fringements upon the rights of third parties that may result from its
use.
The material in this document is for product information only and is
subject to change without notice. While reasonable efforts have been
made in the preparation of this document to assure its accuracy,
AAEON assumes no liabilities resulting from errors or omissions in
this document, or from the use of the information contained herein.
AAEON reserves the right to make changes in the product design
without notice to its users.

Network Appliance
FWS-7600
ii
Acknowledgments
All other products’name or trademarks are properties of their
respective owners.
Award is a trademark of Award Software International, Inc.
CompactFlash™is a trademark of the Compact Flash
Association.
Intel®, Xeon Quad Core, and Core 2 Duo are trademarks of
Intel®Corporation.
Microsoft Windows®is a registered trademark of Microsoft Corp.
ISoundBlaster is a trademark of Creative Labs, Inc.
All other product names or trademarks are properties of their
respective owners.

Network Appliance
FWS-7600
iii
Caution
There is a danger of explosion if the battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer’s instructions and your local government’s recycling or
disposal directives.
Attention:
Il y a un risque d’explosion si la batterie est remplacée de façon incorrecte.
Ne la remplacer qu’avec le même modèle ou équivalent recommandé par le
constructeur. Recycler les batteries usées en accord avec les instructions du
fabricant et les directives gouvernementales de recyclage.

Network Appliance
FWS-7600
iv
Packing List
Before you begin installing your card, please make sure that the
following materials have been shipped:
1 FWS-7600
1 Quick Installation Guide
1 CD-ROM for manual (in PDF format) and drivers
1 Heatpipe Module
1 Serial ATA Cable
1 Hard Disk Drive Power Cable
2 Ear Brackets
Screw Accessories
If any of these items should be missing or damaged, please contact
your distributor or sales representative immediately.
Note:
PS/2 keyboard/mouse cable and VGA Cable are optional accessories,
please purchase those cables according to the following item
numbers.
1700060150 PS/2 KB/MS Cable

Network Appliance
FWS-7600
v
Contents
Chapter 1 General Information
1.1 Introduction................................................................ 1-2
1.2 Features .................................................................... 1-3
1.3 Specifications ............................................................ 1-4
1.4 General System Information ..................................... 1-7
Chapter 2 Quick Installation Guide
2.1 Safety Precautions.................................................... 2-2
2.2 Location of Connectors .............................................2-3
2.3 Mechanical Drawing..................................................2-4
2.4 List of Jumpers.......................................................... 2-7
2.5 List of Connectors ..................................................... 2-8
2.6 Setting Jumpers ........................................................ 2-9
2.7 CF Power Selection (JP3).........................................2-10
2.8 Clear CMOS (JP4) .................................................... 2-10
2.9 BUZZER (FP2)..........................................................2-10
2.10 Front Panel Connector (FP1).................................. 2-10
2.11 Front Panel Connector (FP2).................................. 2-10
2.12 USB Connector (USB1) ..........................................2-11
2.13 USB Pin Header (CN4, CN6)..................................2-11
2.14 RS-232 Serial Port Connector (COM1)...................2-11
2.15 RS-232 Serial Port Pin Header (COM2) .................2-12
2.16 Power Connector (ATX2)........................................ 2-12

Network Appliance
FWS-7600
vi
2.17 FAN Connector (FAN1, FAN2, FAN3) ....................2-13
2.18 PS/2 Keyboard/ Mouse Connector (CN2)............... 2-13
2.19 SATA Power Connector (PWR1) ............................2-13
2.20 LCM & Key Pad Control Connector (LCMA1)......... 2-13
2.21 PCIX Power Connector (CN1) ................................ 2-14
2.22 Installing the CPU and the Heatpipe....................... 2-15
2.23 Hard Disk Drive Installation..................................... 2-20
2.24 LAN Module Installation ..........................................2-23
Chapter 3 Award BIOS Setup
3.1 System Test and Initialization ................................... 3-2
3.2 Award BIOS Setup.................................................... 3-3
Chapter 4 Driver Installation
4.1 Installation .................................................................4-3
Appendix A Programming the Watchdog Timer
A.1 Programming .........................................................A-2
A.2 W83627EHG Watchdog Timer Initial Program......A-6
Appendix B I/O Information
B.1 I/O Address Map....................................................B-2
B.2 Memory Address Map............................................B-3
B.3 IRQ Mapping Chart................................................B-4
B.4 DMA Channel Assignments...................................B-4
Appendix C Standard Firewall Platform Setting
C.1 Standard Firewall Platform Setting....................... C-2

Network Appliance
FWS-7600
vii
C.2 Status LED Sample Code..................................... C-3
C.3 LAN Bypass Mode Sample Code......................... C-6
C.4 LCM Sample Code ............................................... C-8
C.5 Console Redirection ........................................... C-14

Network Appliance FWS-7600
Chapter 1 General Information 1- 1
General
Chapter
1
Information

Network Appliance FWS-7600
Chapter 1 General Information 1- 2
1.1 Introduction
FWS-7600 adopts Intel Xeon Quad Core 3200 series up to
2.66GHz or Core 2 Duo 3000 series Processor up to 2.4GHz. The
chipset is equipped with Intel®3010 and Intel®82801FB (ICH7R). In
addition, the system memory features four 240-pin ECC DDRII 667
SDRAM DIMM socket total up to 8GB and supports dual-channel.
FWS-7600 deploys ten LAN ports that can use four PCI-E［x1］
copper LAN with four ports bypass function and two PCI-E［x4］dual
fiber LAN modules or features four SFP on the modules. The
condensed appearance of FWS-7600 features 1U form factor that
fits nicely into a space- limited environment.
This compact FWS-7600 is equipped with one ATA-100 that
supports CD-ROM ATAPI devices, two SATA II and
CompactFlashTM Type II connector with ATA mode. In addition,
it offers flexible expansion with network products and features
one Mini PCI expansion slot, six USB2.0 ports and two RS-232
console ports. The console port deploys console re-direction
that increases the network security via remote control.
Moreover, there is a front panel support LCM with keypad control
that allows for easy access and operation. All of these designs
provide for a more user-friendly solution.

Network Appliance FWS-7600
Chapter 1 General Information 1- 3
1.2 Features
 1U Network Appliance Platform Up To 10 LAN Ports
 Intel®Xeon Quad Core 3200 Series Up to 2.66GHz &
Dual Core 3000 Series CPU Up To 2.4GHz
 240-Pin Dual-Channel ECC DDRII 667 SDRAM DIMM x
4 Support Up To 8GB
 Fiber Ethernet x 4 & Gigabit Ethernet Module x 4 For
Optional (4-port Bypass Function)
 Ultra ATA-100 Port x 1 & SATA II x 2
 CompactFlash Type-II Connector & Mini PCI Type-III
Connector
 300W Power With Auto Range Input
 USB2.0 Port x 6 (Pin Header x 4, Type A Port x 2 On
Front Panel)
 Parallel LCM With Keypad x 1 & RS-232 Console x 1 On
Front Panel
 Watchdog Function 1~255 Sec.
 Internal 3.5" Disk Drive Bay x 1

Network Appliance FWS-7600
Chapter 1 General Information 1- 4
1.3 Specifications
System
Construction: 1U firewall heavy-duty steel system up
to 10 ports
CPU Intel® Xeon Quad Core 3200 series up
to 2.66GHz and Dual Core 3000 series
CPU up to 2.4GHz, Tc=82W @ 70℃
Memory 240-pin ECC DDRII 667 DIMM Socket
x 4, total up to 8GB, Support
Dual-Channel
LAN (Optional)
BIOS
IDE
SATA Interface
Solid Storage Disk
PCI-E［x1］10/100/1000Mb LAN
module x 4 w/ Intel 82573 (with 4-port
bypass), PCI-E［x4］Dual Fiber LAN
module x 2 w/Intel 82571, SFP x 4
Award Plug & Play FWH BIOS – 8Mb
ROM
ATA-100 x 1 channel (Supports
CD-ROM ATAPI devices)
SATA II x 2
Supports CFD Type II connector(ATA
mode)
Note: Please change the IDE BIOS setting to “Slave” when you use the
CF and IDE.

Network Appliance FWS-7600
Chapter 1 General Information 1- 5
Expansion Interface Mini PCI Type III Socket & PCI/
PCI-X/ PCI-E［x1］slot
Note: FWS-7600 supports three types of add-on cards: PCI, PCI-X and
PCI-Express, and not intended to use for any TELECOMMUNICATION
NETWORK device. (Such as modem card.)
Watchdog Timer
RTC
Storage
1~255 steps, can be set with software
on Super I/O
Internal RTC
Internal：One 3.5" Hard Disk Drive Bay
System Fan Three 4cm Ball Bearing Fans
Color
LCM
Power Supply
Blue and Red
2 x16 characters with 4 keypad control
ATX 300W, auto range
Dimensions
Net Weight
EMC
Safety
I/O
Serial Port
Keyboard & Mouse
16.93” (W) x 19.69” (D) x 1.73”(H)
(430mm x 500mm x 44mm) —Chassis
9.84” (W) x 11.02” (D) (250mm x
280mm) —Board
17.6 lb (8 kg)
CE/FCC Class A
UL
Two COM ports: (Internal Pin Header
x 1)
COM 1: RS-232
COM 2: RS-232 (Pin Header)
Reserve pin header

Network Appliance FWS-7600
Chapter 1 General Information 1- 6
Universal Serial Bus
Front I/O Panel
Rear I/O panel
Six USB 2.0 Ports
Two Dual Type A Connector on front
panel
Four Pin Header (Internal)
One Bypass LED
One Power LED
One Status LED
One HDD Active LED
LAN LEDs
Two USB Ports
LAN Ports
One DB-9 connector
One LCM Display
One Reset Button
One PCI-E［x1］/ PCI-X/ PCI expansion
slot
Environmental
Operating Temp. 32°F ~ 104°F (0°C ~ 40°C)
Storage Temp. -4°F ~ 140°F (-20°C ~ 60°C)
Operating humidity: 10 ~ 80%
Storage humidity: 10 ~ 80% @ 40°C, non-condensing
Vibration 0.5G / 5 ~ 500Hz / operation (3.5” Hard
Disk Drive)
1.5G / 5 ~ 500Hz / non operation

Network Appliance FWS-7600
Chapter 1 General Information 1- 7
Shock
10G peak acceleration (11 m sec.
duration), operation
20G peak acceleration (11 m sec.
duration), non operation

Network Appliance FWS-7600
Chapter 1 General Information 1- 8
1.4 General System Information
Front Panel
LEDs for Bypass, HDD Active, Status, Power
Console Port 4 LAN Ports
4 SFP Keypad Control
2 USB Ports
Modules could be two
fiber modules or one
fiber and one copper
combination modules.

Network Appliance FWS-7600
Chapter2QuickInstallationGuide2-1
FWS-7600
Chapter
2
Quick
Installation
Guide
Notice:
The Quick Installation Guide is derive
d
f
rom Chapter 2 of the user manual. Fo
r
other chapters and further installation
instructions, please refer to the use
r
manual CD-ROM that came with th
e
p
roduct.
Part No. 2001760011 Printed in Taiwan April 2009

Network Appliance FWS-7600
Chapter 2 Quick Installation Guide 2-2
2.1 Safety Precautions
The installation is intended for technically qualified personnel who
have experience installing and configuring system boards.
The equipment can be installed in a restricted access location (RAL)
only.
A restricted access location is a site location for equipment where
the following criteria apply:
01. Access can only be gained by service persons or by users who
have been trained on the restrictions and the precautions for this
specific site.
02. Access is by means of at least one of the following, special tool,
lock and key, or other means of security, and is controlled by the
authority responsible for the location.
Safety Precautions:
Always completely disconnect the power cord from
your board whenever you are working on it. Do not
make connections while the power is on, because a
sudden rush of power can damage sensitive
electronic components.
Always ground yourself to remove any static charge
before touching the board. Modern electronic devices
are very sensitive to static electric charges. Use a
grounding wrist strap at all times. Place all electronic
components on a static-dissipative surface or in a
static-shielded bag when they are not in the chassis
Risk of explosion if the battery is replaced by an
incorrect type. Dispose of used batteries according to
the instructions.

Network Appliance FWS-7600
Chapter 2 Quick Installation Guide 2-3
2.2 Location of Connectors
Board of FWS-7600
Component side

Network Appliance FWS-7600
Chapter 2 Quick Installation Guide 2-4
2.3 Mechanical Drawing
Board of FWS-7600
Component Side