Abask J05 User manual
User Manual
Contents
English…….......……………….…….1-17
Deutsch…………….......……………18-35
Français………………….......………36-53
Italiano……………….....………….… 54-71
Español………………...….......…….. 72-89
1
Please format the memory card in the camera menu at the
first use.
This camera records video at high resolution. Be sure to
use a high-speed Micro SD card (Class 10 or above, max
supports 64GB.) For safety reasons, the built-in battery is
only used for emergency backup files.
To work, the dash cam must be connected to the car's
cigarette lighter socket or hardwired to the car's fuse box.
The video from the front camera can be reviewed directly
from the dash cam or PC, but what was recorded by the
inside camera can only be reviewed through PC. Therefore,
please connect the camera to the PC by the attached USB
cable or just remove the memory card and read it on PC to
review the footage.
Warm Tips:
English
2
Interface and Button Function
1.Front Camera
2.Microphone
3. Screen
4.IR LED Lights
5.Inside Camera
6.Mini USB Port
7.Mount Socket
8.Left
9.Menu
10.Right
11.OK
12.Power
13.Reset Hole
14.Memory Card Slot
1
6
8910 11 12
13 14
3
2
75
4
3
Long press to turn ON / OFF the camera power.
Press to turn/off the screen.
In video mode, press to start/ stop video recording
In camera mode, press to take a photo.
In menu setting, press to confirm selection and
adjustment.
In playback mode, press to select and play
recorded files.
In menu setting, press to select option.
In standby mode or video recording modes, press
to switch front and inside display views.
In playback mode, press to select media files.
Long press to turn on/ off the LED light for the
inside camera.
In standby mode, press to access the menu settings,
and press twice to access System Setting Menu.
Return function: Press to return to the previous page.
In standby mode, long press to switch mode between
Video / Photo / Playback.
During video recording, long press to lock/ unlock
the current footage.
In menu setting, press to select option.
In playback mode, press to select media files.
During video recording, press to turn on/ off audio
recording while long press to on/ off parking monitor
function.
Button Function
Power
OK
MENU
▶
(RIGHT)
◀
(LEFT )
4
1. Before installation, please check the camera‘s normal fun-
ction, and make sure you are using a high-speed Micro SD
card( speed Class 10 or above ), and format the card in the
camera menu at the first use.
2. Use the suction cup mount to install the dash cam on the
windshield. The recommended location is near the inside view
mirror facing front.
3. Adjust the lens angle of the camera, make sure you get the
best coverage over the hood and the road ahead, so you can
record what happens.
4. Connect the camera to the car by the cigarette lighter, hide
the rest of the cable in the gap of the interior trim board.
�
�
Set up and Installation：
5
The dash cam operates in 3 modes: Video Recording Mode,
Photo Mode and Playback Mode. These modes also have
the menu to help you configure recording and taking photos.
Long press menu button to switch between different modes
and access to the mode you want. The represented icon for
each mode shows on the top left corner of the screen.
The camera will automatically enter Video Recording Mode
and start recording when connected to a car charger and
power on. A Red dot flashing on the top left corner indicates
record is in progress. Press the OK to stop recording, or start
recording again. The following are icon representations of
some common functions on the screen, indicating that these
functions are enabled. (You can also find their representations
through the menu accordingly).
1 . Video Recording Mode
2 . Loop Recording
3 . Exposure
4 . Motion Detection
5 . HDR
6 . G-sensor
7 . Recording Time
8 . Resolution
9.Parking Monitor
10 . LED Light Status
11 . Memory Card Status
12 . Power Status
13 . Audio Status
14 . Time & Date
Operating Modes:
Video Recording Mode:
6
In all 3 operating mode , you can press the MENU button
once to access the menu settings for that particular mode,
and press twice to display System Setting Menu.
The System Setting Menu is common to all modes.
Press ◀ and ▶to scroll through the various setting options
and press OK to select and confirm selection, Press MENU
again to exit the setting menu.
Adjust front camera recording video resolution
1080FHD / 720P / VGA, the inside camera will keep recor-
ding at 1080P.
Video Recording Menu :
Resolution:
Continuously record small video files of a
length which is determined by the settings of 1/ 2/ 3 Mins.
For example, if it is set for 3 minutes, the camera will auto-
matically save a section of videos every 3 minutes. When the
memory gets full, the dash cam will automatically delete the
oldest video to record the latest video, which can avoid a la-
ck of memory.
Loop Recording:
Turn on to optimize video quality withHigh Dynamic Range:
+
-
< >
>
<
7
wider light range and image details.
Adjust the exposure value to adjust the brightness
of the video.
Exposure:
Turn ON / OFF motion detection function.Motion Detection:
Turn ON / OFF audio recording in the video.Recording:
Enable / Disable the date and time marks in
video files.
Date Stamp:
G-G-sensor detects significant or sudden shock
and movement, then automatically locks the current file from
loop recording. Its sensitivity is adjustable (Off/ Low/ Medi-
um/High)
G-Sensor:
Note: To use this function wh-
en the car is parked, please buy a hard-wire kit (mini USB
type) for dash cam then connect to the vehicle’s fuse box
power so as to supply the power to the camera.
Parking Monitor: It's used to protect your car after parking.
With this function on, after you stop the car and the camera
turns off, it stays standby. When camera detects shock and
collision, it will automatically turn on and take a short video,
then shut down automatically.
< >
>
<
8
The camera can operate in Photo Taking Mode.
Set the photo resolution.
VGA/1M/2M/3M/5M/8M/10M for choices.
Photo Taking Mode:
In standby mode, long press MENU to switch to Photo Mode,
and press OK to take a photo.
Photo Mode Menu :
Resolution:
Turn on / off image stabilization function.Anti-shaking:
Enable / Disable the date and time marked in
image files.
Date Stamp:
To take a photo:
Like the Video Recording Mode, you can press the Menu bu-
tton once to access the setting menu for Photo Mode, Press
Menu twice to enter the system setting menu.
< >
>
<
9
This mode allows you to play back recorded video or view
photos
1.Stop video recording, long press MENU button twice to
enter playback mode.
2.Use ◀and ▶ button to scroll through the recorded files
/photos, and press OK to view recorded video.
After choosing a recorded video or photo, press the Menu
button once to access the setting menu for Playback Mode.
Playback Mode:
Playback Menu:
Press MENU button twice to access System Setting Menu in
any mode. The TOOL icon is highlighted in the upper left co-
rner.
System Setting Menu :
Delete the current file displayed or delete all files.Delete :
Lock / Unlock the current file displayed or lock
/ unlock all files.
Protection :
< >
>
<
10
Set the timing to automatically turn off the
LCD display after no operation so as to have the product
worked in very low power consumption; There are "Off, 30s,
1 Min, 2 Min" in this setting. For example, if it is set "30s",
the screen will turn off after 30 seconds, but the camera is
still working(recording). When you want to turn on the scr-
een, you can press any button to activate the screen.
Screen Saver :
Set the time for the camera to automati-
cally power off to save power . The camera will automatic-
ally power off when it is standby under the setting time. Off
/ 1 Minute/ 3 Minutes/ 5 Minutes
Auto Power Off :
Set light frequency to 50HZ or 60HZ a-
ccording to local regulation.
Light Frequency :
Turn on / off sound that when pressing any
button made.
Beep Sound:
Choose the camera system language: Chinese/
English/French/German/Italian/Spanish /Japanese.
Language :
< >
>
<
Ｈｚ
ＯＦＦ
ＬＣＤ
11
Format/ delete all data from the Micro SD card.Format :
Reset all settings back to factory default.Restore Setting :
Check firmware version.Version :
Set the time and date by using the LEFT
and RIGHT button, then press OK to confirm changes,
press MENU button again to exit time setup.
Date / Time :
Set up the IR LED lamp working mode for the
inside camera, On/ Off or Auto. In Auto mode, the IR LED
will light when the light inside the car is too dark.
LED Light :
< >
>
<
Ｖ．１．０
ｆ
12
Specification
Model J05
Video Resolution 1080FHD/720P/VGA
Photo Resolution VGA/1M/2M/3M/5M/8M/10M
Screen 1.5 inch LCD Display
Angle 170° High-Resolution Wide Angle Lens
Front : 1920 * 1080P(highest), inside :
1920 * 1080P
Frame Rate 30fps
Effective Pixels 2MP
H.264, MOV
Photo Format JPEG
Screen Saver Supported
Loop Recording Off/ 1 Minute / 2Minutes / 3 Minute
HDR Supported
G-sensor Lock Supported
IR LED Lamps 4 pcs
Chinese/English/French/German/
Italian/Spanish /Japanese
Audio Recording Built-in microphone, On / Off optional
Storage Micro SD Card (Class 10, up to 64GB )
USB interface Mini USB
DC 5V / 0.8A
Light Frequency 50HZ/60HZ
Battery 200mAh polymer lithium battery
-20℃ - 60℃
-10℃ - 50℃
Video Resolution
Video Coding Format
Language
External power supply
Storage temperature
Operating temperature
13
Have set loop recording, but only randomly records
for seconds with a long gap in between, then stops and
re-start the recording.
FAQ :
Q 1:
Q 2 : The SD card gets full and it doesn't overwrite?
Have set loop recording, but only randomly records for
seconds with a long gap in between, then stops and re-
start the recording.
A:
Please check whether all video files are locked( if loc-
ked, there will be a "key" icon at the top left on the screen
when you replay the files ). Those locked files cannot be
overwritten by loop recording while needed to be delete
manually, please format micro SD card and adjust sensit-
ivity of G-sensor.
A:
Q 3 : Can it take pictures and can you replay the re-
corded videos on it?
Yes, it can take pictures as it has got camera mode.
Please long press MENU button to switch around modes
of video--camera-- file playback . The video from the
front camera can be replayed directly from the dash cam
or PC.
A:
Q 4: Why I can’t see records of the inside camera w-
hen I playback through the camera?
14
What was recorded by the inside camera can only be
reviewed through PC. Therefore, please connect the cam-
era to the PC by the attached USB cable or just remove
the memory card and read it on PC to review the footage.
A:
Q 5: If I see an accident which I'm not part of but it's
been captured by the camera, how can I save that re-
cording? What button would I press?
If so, you need to manually lock the video to protect it
from overwriting, there are 2 ways: (1) Please long press
the MENU button to lock the current recording video, you
will see a "key" icon appear on the screen; (2) Or stop the
car, but still let the car start( to power the dash cam), and
then playback the video, find the related video, press MENU
button to protect it.
A:
Q 6: How does the inside camera run?
The inside view will automatically show on the screen
with power on. In standby mode or video recording modes,
press ◀button to switch front and inside display views.
A:
Q 7: The internal battery, despite receiving a one-night
charge, barely lasts a few minutes? /Without external
power supply, the camera only lasts very short time,
or just can't turn on?
The built-in battery is only to save files urgently in case A:
15
Q 8: The parking monitor does not work?
All dash cams on the market are powered by the car.
After the dash cam is plugging in the car cigarette lighter
socket, while starting the car, the car will supply power to
the dash cam, the dash cam will turn on and record the
video. However, once the car shuts down, the dash cam
shuts down and also stops recording. Therefore, it does
not react to movements and impacts after the engine is
switched off.Therefore, if you want to activate the dash
cam to monitor your car after the car shuts down during
overnight parking, the dash cam needs to be wired to the
car's fuse box. Please purchase a "dash cam hard wire kit"
(mini USB type) separately.
A:
of sudden power off. The dash cam is powered by the
car. The car camera will automatically switch on/off w-
hen the car engine ignition is on/off. No need to charge
the dash cam or worry about the battery level. It is not d-
esigned to work without external power supply, so please
keeps the camera connecting to car's cigarette lighter
socket, while you starts the car, your car is supplying
power to the dash cam, the dash cam will turns on and
record video. However, once the car turns off, the dash
cam will turn off and stop recording as well. If you don't
want to connect the cigarette lighter, you can also hard
wire the camera to the car's fuse box. Please purchase a
"dash cam hard wire kit"(mini USB type) separately.
16
Q 9: Suction mount cannot attach on windshield well ?
1. Please clean the windscreen where attaching with a
glass cleaning wipe. Removed the protective film, If it does
not work, warming your windscreen then try it again.
2. Please soak suction mount to warm water for a mo-
ment.
A:
Q 10: The dash cam will stop automatically while
recording?
1. Check whether the memory is full.
2. Check whether the loop recording function is tu-
rned ON.
3. Check whether the Micro SD card is high-speed
above C10.
4. Check the memory card, there might be too many
locked video that the loop recording won't work right.
5. Check the car charger connection status, if the
connection is loose, the power supply is not stable, the
power supply is not stable, the camera will automatically
turn off.
6.Check whether it is just because of the Screen
Saver on.
A:
Q 11: The camera keeps starting and off?
That could be the parking monitor function being tri-
ggered, check the setup menu.
A:
17
Q 12 : There are stripes interference in the image?
That should be wrong light frequency. According to
the local regulation, choose the appropriate frequency
settings 50HZ or 60HZ.
A:
18
Bitte formatieren Sie bei der ersten Verwendung mit dem
Kameramenü die Speicherkarte.
Diese Kamera zeichnet Videos mit hoher Auflösung auf.
Verwenden Sie unbedingt eine Hochgeschwindigkeits-Micro
-SD-Karte (Klasse 10 oder höher, max. Unterstützt 64 GB).
Verwenden Sie bitte aus Sicherheitsgründen nur den einge-
bauten Akku für Notfall-Backup-Dateien.
Schließen Sie bitte Dash Cam an die Zigarettenanzünder-
buchse des Autos oder anden Sicherungskasten des Autos
an.
Das Video von der Frontkamera kann direkt von der Dash
Cam oder dem PC aus überprüft werden. Was jedoch von
der Innenkamera aufgenommen wurde, kann nur über den
PC überprüft werden.Schließen Sie daher die Kamera über
das angeschlossene USB-Kabel an den PC an oder entfe-
rnen Sie einfach die Speicherkarte und lesen Sie sie auf
dem PC, um das Filmmaterial zu überprüfen.
Warme Tipps:
Deutsche
Table of contents
Languages:
Other Abask Dashcam manuals
