Abilica Abilica Spin Use and care manual

1
Assembly- and user’s manual for
Abilica Spin
Art. No: 555 046

2
COMPLETE PARTS-DRAWING

3
COMPLETE PARTS LIST
NO
NAME
QUANTITY
REMARK
1
RIGHT PEDAL (R)
1
2
END CAP 1
2
3
CARRIAGE BOLT (M8*70)
4
4
REAR STABILIZER
1
5
CURVED WASHER (Ø 8)
4
6
DOMED NUT
4
7
SPRING ADJUSTMENT KNOB
3
8
INSERT PLASTIC
3
9
LEFT PEDAL (L)
1
10
VERTICAL SEAT POST
1
11
END CAP 2
1
12
SEAT POST
1
13
SEAT
1
14
END CAP 3
2
15
FRONT STABILIZER
1
16
MAIN FRAME
1
17
HANDLEBAR POST
1
18
HANDLE BAR
1
19
SPRING WASHER
4
20
BOLT (M8*15)
4

4
FIG.1
ASSEMBLY
:
FIG.2
FIG.2:
Slide the Vertical Seat Post (pt.10)
into the seat post housing on the main
frame (pt.16). Then slide the Seat
Post (pt.12) into the Vertical Seat Post
(pt.10). You will have to slacken the
knurled section of the Spring
Adjustment Knob (pt.7) and pull the
knob back and then select and align
holes for the desired height. Release
the knob and retighten the knurled
portion.
Now fix the Seat (pt.13) to the Vertical
Seat Post (pt.12) as shown, and
tighten the bolts around the screws
under the seat.
FIG.1:
Remove the bolts and nut from the
bottom tube, then attach the Front
Stabilizer (pt.15) to the Main Frame
(pt.16) using two sets of Ø8 Curved
Washers (pt.5), M8 Domed Nut (pt.6)
and M8*70 Carriage bolt (3).
Attach the Rear Stabilizer (pt.4) to the
Main Frame (pt.16) using two sets of
Ø8 Curved Washers (pt.5), M8 Domed
Nut (pt.6) and M8*70 Carriage bolt (3).

5
FIG.3
FIG.4
FIG.3:
Slide the Handlebar Post (pt.17) into
the handlebar post housing on the main
frame. You will have to slacken the
knurled section of the Spring
Adjustment Knob (pt.7) and pull the
knob back and then select and align
holes for the desired height. Release
the knob and retighten the knurled
portion.
Then fix the Handlebar (pt.18) with four
sets of Ø8 the Spring Washer (pt.19)
and M8*15 the Bolt (pt.20).
FIG.4:
The Pedals (pt.9 L & pt.1 R) are
marked "L" and "R" - Left and Right.
Connect them to their appropriate
crank arms. The right crank arm is on
the right- hand side of the cycle as you
sit on it.
Note that the Right pedal should be
threaded on clockwise and the Left
pedal anticlockwise.

6
ADJUSTMENT
To adjust seat height, slacken the tension knob on the vertical seat
post, and pull the knob out. Adjust the seat to desired height and
make sure the holes align. Release the knob and retighten it.
To move the seat forward in the direction of the handlebar or
backwards away from it, loosen the adjusting knob and washer and
pull the knob back. Slide horizontal seat post into desired position.
Align holes and then retighten the adjusting knob.
To adjust the handlebar height, slacken the spring knob and secondary
Knob and pull both knobs back. Slide the handlebar post along the
housing on the main frame to the desired height and, with the holes
aligned correctly, tighten the spring adjusting knob and then the
secondary knob.
The tension control knob allows you to alter the resistance of the pedals.
A high resistance makes it more difficult to pedal, and is acheived by
turning the tesnion knob clockwise. A low resistance makes it easier to
pedal, and is acheived by turning the tension knob counterclockwise.
Supplier:
Sport Supply Int. AS
PO Box 244
N-3051 Mjøndalen
Norway
E-mail: [e-mail]
www.abilica.com
www.sportsupply.no
© Sport Supply Int. AS