Abus SHLM10000 User manual
2
English
Introduction
Dear customer,
We are pleased that you have chosen our product and thank you for your trust! You made a good
choice.
This Bulb (hereinafter referred to as the "device") has been developed and manufactured with the
utmost care. Please read these operating instructions completely and observe all operating and safety
instructions, as this ensures the best possible handling of the device. This document is an installation
and maintenance manual.
If you have any questions, please contact your specialist trade partner
or contact our customer service:
Mail: ABUS Support, Linker Kreuthweg 5, 86444 Affing, Germany
E-mail: support@abus-sc.com
Phone: +49 8207 959 90 888
Hotline opening hours: Mon-Thu: 08 - 17 h; Fri: 08 - 14 h
ABUS Security-Center hereby declares that the enclosed product comply with the requirements
of the following directives
RED Directive (2014/53/EU), EMC Directive (2014/30/EU), Low Voltage Directive (2014/35/EU) and
RoHS Directive (2011/65/EU). The full EU Declaration of Conformity text can be found at:
www.abus.com/product/SHLM10000
www.abus.com/product/SHLM10010
It can also be obtained at the following adress:
ABUS Security-Center GmbH & Co. KG,
Linker Kreuthweg 5, 86444 Affing, GERMANY
All contained company names and product designations are trademarks of the respective owners. All
rights reserved.
Disclaimer of Liability
These operating instructions have been prepared with the greatest care. Should you nevertheless
notice omissions or inaccuracies, please inform us in writing at the above address.
Your rights are limited to the repair or replacement of this product as delivered. ABUS Security Center
assumes no liability for any special, incidental or consequential damages, including but not limited to
loss of revenue, loss of profit, restrictions in the use of the software, loss or recovery of data, costs
for replacement equipment, downtime, property damage and claims of third parties, as a result of and
in connection with the use of the software.a. warranty, contractual, legal or claims for damages
notwithstanding other limited or implied warranty provisions or in the event that the limited warranty
does not apply, the scope of liability of ABUS Security Center is limited to the purchase price of the
product.
The contents of this manual are subject to change without notice.
© ABUS Security-Center GmbH & Co. KG, 09/2018
3
English
Important Safety Informations
Intended Use
Only use the device for the purpose for which it was built and designed. Any other use is considered
unintended.
All guarantee claims are invalid in the event of damage caused by non-compliance with this
safety information. We cannot be held liable for resulting damage.
Unboxing
Handle the device with extreme care when unpacking it.
Packaging and packaging aids can be reused and, as far as possible, should be sent for recycling.
If the original packaging has been damaged, inspect the device first. If the device shows signs
of damage, return it in the original packaging and inform the delivery service.
Installation location / operating environment
Do not place any heavy objects on the device. The device is only designed for operation in spaces with
appropriate temperatures or humidity (e.g. not for bathrooms). Do also not place the device in areas
with excessive accumulation of dust. Please refer to the individual devices' technical data for more
detailed information. Ensure that: adequate ventilation is always guaranteed; no direct sources of heat
can affect the device; interior devices are not exposed to direct sunlight or strong artificial light; the
device is not in the immediate vicinity of magnetic fields (e.g. loudspeakers); no naked flames (e.g. lit
candles) are placed on or next to the device; sprayed or dripping water is prevented from coming into
contact with interior devices and caustic fluids are avoided; the device is not operated in the vicinity of
water, in particular, the device should never be submerged (do not place objects containing fluids, e.g.
vases or drinks, on or near the device); no foreign bodies penetrate the device; the device is not
exposed to wide temperature variations, as otherwise there may be condensation from humidity causing
electrical short circuits; the device is not exposed to excessive shock or vibration.
Children
Keep electrical devices out of reach of children. Never allow children to use electrical devices
unsupervised. Children may not always properly identify possible hazards. Small parts may be fatal if
swallowed. Keep packaging film away from children. There is a risk of suffocation. This device is not
intended for children. If used incorrectly, parts under spring tension may fly out and cause injury to
children (e.g. to eyes).
4
English
Information on handling batteries
▪Make sure that batteries are kept away from small children. Children may put batteries in their
mouths and swallow them. This can cause serious harm to their health. If this happens, consult
a doctor immediately.
▪Do not charge normal batteries, heat them up or throw them into naked flames (they may
explode).
▪The battery must not be directly exposed to heat or sunlight, and must not be stored in a place
with a very high temperature.
▪The battery must not come into contact with water.
▪The battery must not be dismantled, pierced or otherwise damaged.
▪The battery contacts must not be short-circuited.
▪Change low batteries in good time.
▪Always change all the batteries at the same time and use batteries of the same type.
▪Leaky or damaged batteries can cause chemical burns on contact with the skin. In this case,
wear protective gloves. Clean the battery compartment with a dry cloth.
Important information on battery disposal
Batteries with this label do not contain harmful substances such as cadmium, lead and
mercury. However, used batteries must not be disposed of along with household waste
in accordance with the battery directive. To protect natural resources and promote the
recycling of materials, separate the batteries from other waste and deposit them at a
local recycling center. An additional label with the chemical symbols for Hg, Cd or Pb
means that the batteries contain quantities of mercury, cadmium or lead which exceed
the restrictions set by the EU Directive 2006/66/EG. If batteries are not disposed of
properly, these substances can cause harm to human health or the environment
Cleaning
▪Dusty devices must be cleaned. You can clean dust from the air vents using a vacuum cleaner
or compressed air. If necessary, you can remove the dust with a brush.
▪You can clean the surface using a cloth slightly dampened in soapy water. Only use suitable
microfiber cloths for high-gloss surfaces.
▪Do not allow water to penetrate the device.
▪Do not clean the device in a dishwasher.
▪Do not use sharp, pointed, abrasive or corrosive cleaning materials or hard brushes.
▪Do not use chemicals.
▪Do not use flammable liquids for cleaning the device.
Information on device disposal
Important: The EU Directive 2012/19/EU regulates the proper return, treatment and
recycling of used electronic devices. This symbol means that in the interest of
environmental protection the device must be disposed of separately from household or
industrial waste at the end of its service life in accordance with applicable local legal
guidelines. Disposing of used devices can be done at official recycling centers in your
country. Obey local regulations when disposing of material. Further details on returns
(also for non-European countries) can be obtained at your local authority. Separate
collection and recycling saves natural resources and ensures that all the provisions for protecting health
and environment are observed when recycling the product.
5
English
Table of contents
1. Product introduction ......................................................................................................................... 6
1.1. Scope of Delivery..................................................................................................................... 6
1.2. Operating principle .................................................................................................................. 6
1.3. Performance Features............................................................................................................. 6
1.4. Use in systems of different manufacturers.............................................................................. 6
2. Overview of functions....................................................................................................................... 7
2.1. Inclusion / Add Device............................................................................................................. 7
2.2. Operating................................................................................................................................. 8
2.3. Exclusion / Remove Device..................................................................................................... 8
2.4. Reset (Factory-Reset) ............................................................................................................. 8
3. Advanced Z-Wave Parameter.......................................................................................................... 9
3.1. Association Group Information ................................................................................................ 9
3.2. Overview Configuration Parameter ......................................................................................... 9
3.3. Command Classes .................................................................................................................. 9
4. Technical Specifications................................................................................................................. 10
6
English
1. Product introduction
1.1. Scope of Delivery
▪ABUS Z-Wave RGBW/LED Bulb
▪Quickguide & Safety instructions
1.2. Operating principle
The SHLM100x0 was developed for use in home automation systems that use the Z-Wave wireless
standard. The LED bulb fits into any standard E27 socket and can be dimmed individually. Via app you
also have the choice of over a thousand colours (SHLM10000)
In conjunction with configurable scenes, smart functions can be initiated, e.g. when light on after 8 pm,
with 30% brightness on, if before 8 pm with 90% brightness.
1.3. Performance Features
Die ABUS Z-Wave SHLM10000/SHLM10010...:
▪…is an smart Radio-LED-Bulb
▪…is Z-Wave PLUS compatible & certified
▪…has an adjustable dimming range
▪… has five colour channels: red, blue, green, warm white. cool white (SHLM10000)
▪…can be switched on/off manually or via radio/gateway
▪…was developed for indoor installation
1.4. Use in systems of different manufacturers
Communication is via the Z-Wave EU frequency (868.42 Mhz). You can integrate the device into any
Z-Wave network with a certified Z-Wave gateway, regardless of manufacturer. All non-battery powered
nodes in the network act as repeater to increase the durability of the network.
7
English
2. Overview of functions
2.1. Inclusion / Add Device
Screw the LED bulb into a standard E27 socket
Click the + (Add) button in your Z-Wave App and follow
the further instructions
Turn the light-switch on.
The App will show if the Add device process was
successful and the LED-bulb will flash once
Repeat the inclusion process if it was not successful.
8
English
2.2. Operating
Do not dim the LED bulb via the supply voltage (e.g. dimmer switch) but use the App or compatible Z-
Wave wireless switches/dimmer.
Make sure that the power supply of the LED lamp is always switched on (e.g. wall switch ON), as this
is the only way the device can function.
2.3. Exclusion / Remove Device
Click the - (Remove) button in your Z-Wave App and
follow the further instructions
Switch the LED bulb on.
The App will show if the Remove device process was
successful. The LED bulb will flash once and then dim
to 5%
Repeat the exclusion process if it was not successful.
2.4. Reset (Factory-Reset)
Switch the Power supply oft he LED bulb ON and OFF
6 times in a row. (Interval of 0.5 to 2 seconds)
When switched on for the 6th time, the LED bulb
flashes twice indicating successful reset to factory
settings.
Note:
This procedure should only be used if the primary
gateway is not capable of acting.
If the device is set to the factory setting, the status is
set to "not included", the association settings and
possible configurations are reset to default.
9
English
3. Advanced Z-Wave Parameter
3.1. Association Group Information
Z-Wave devices can control other devices directly. This direct control is called in Z-Wave association.
For this purpose, the device ID of the device to be controlled must be stored in the controlling devices.
This is done in so-called association groups. An association group is always linked to an event in the
controlling device (pressing a key or triggering a sensor). When this event occurs, a control command
- usually a BASIC SET - is sent to all devices stored in an association group.
The device supports the following association group:
Group
Number
Maximum
Devices
Transmitted Content
Group 1
1
(0x01)
Z-Wave Plus Lifeline
3.2. Overview Configuration Parameter
Z-Wave products can be used in the network immediately after inclusion. Through configuration
settings, however, the behaviour of the device can be adapted even better to the requirements of the
application and additional functions can be activated.
Para-
meter
Byte-
size
Funktion
Default-Value
(Decimal)
Description
1
1
Temperature of
NTC
-
This parameter can only be read and not set.
255
4
Reset
-
This parameter cannot been read, but only set
▪2290649224 = Reset to factory
configuration and removed the Z-Wave
network.
▪2281701376 = Reset Configuration
parameter to default value.
(Hexadezimal: 0x88888888 / 0x88000000)
3.3. Command Classes
1. Association Group Information V1
2. Association V2
3. Basic V1
4. Color Switch V1
5. Configuration V1
6. Device Reset Local V1
7. Firmware Update MD V2
8. Manufacturer Specific V2
9. Multilevel Switch V2
10. Power level
11. Security V1
12. Switch All V1
13. Version V2
14. Z-Wave Plus Info V2
10
English
4. Technical Specifications
Parameters
Unit
SHLM10000
SHLM10010
Dimensions
mm
6 x 6 x 11,5
6 x 6 x 11,5
Weight
g
135
70
Operating Temperature
°C
-20 –40
-20 –40
Max. Humidity
%
95
95
IP Class
20
20
Radio frequency
MHz
868,42 (Z-Wave PLUS, Europe)
868,42 (Z-Wave PLUS,
Europe)
Modulation
FSK (BFSK/GFSK)
FSK (BFSK/GFSK)
Transmission power
db
< 4,5
< 4,5
Power supply
VAC
220 - 240
220 - 240
Luminous Flux
lm
806
806
Color temperature
Kelvin
2700 - 6500
2700
Dim factor
%
5 - 100
5 - 100
Beam angle
°
240
240
Lamp Life
h
25000
25000
Socket
E27
E27
Power consumption
standby
W
<0,5
<0,5
Power consumption
W
>9,5 Ǿ
>9,0 Ǿ
Max. Range (building)
m
< 40
< 40
Firmware updateable
Yes
Yes
Support Z-Wave
Beaming
Yes
Yes
SmartStart supported
No
No
Z-Wave Network
Security
Yes
Yes
Z-Wave AES-128
Security
Yes
Yes
Z-Wave Plus
Yes
Yes
Security S2 Classes
No
No
Z-Wave Chip Generation
500
500
Z-Wave Sensor-Type
Open/Closed (Binary)
Open/Closed (Binary)
Zwave library type
Enhanced 232 Slave
Enhanced 232 Slave
Device Type / Role type
Light Dimmer Switch / Always on
Slave
Light Dimmer Switch /
Always on Slave
This manual suits for next models
1
Table of contents
