Acces I/O products USB3C-104-HUB User manual

ACCES I/O Products, Inc. MADE IN THE USA USB3C-104-HUB Manual
1Rev B4d
RUGGED USB3.1 GEN25-PORT C&AHUB
WITH PD (POWER DELIVERY)HARDWARE MANUAL
MODELS
USB3C-104-HUB

ACCES I/O Products, Inc. MADE IN THE USA USB3C-104-HUB Manual
2Rev B4d
CHAPTER 1: QUICK START
No software is provided with this board. There is no need to install
any drivers for the USB3C-104-HUB product.
Using the USB Hub Class Driver (that is built into Windows OS or
Linux etc) it will enumerate as three things:
•Generic Hub
•Super Speed Hub
•Dock Management Controller
CHAPTER 2: INTRODUCTION
•5-port USB 3.1 Gen 2 hub with data transfers up to 10 Gbps
•One upstream USB C with 100 W Power Delivery 3.0 (PD)
•One downstream USB C with 100 W Power Delivery 3.0 (PD)
•Two USB Type C and two Type A downstream ports with Battery
Charging v1.2 and Apple Charging standards
•ESD protection (+/-15kV IEC 61000-4-2 Level 4) on all data lines
•Rugged, industrial grade (-40˚C to 85˚C) operation
•Locking connectors prevent accidental disconnects
•SuperSpeed+ (10Gbps), SuperSpeed (5Gbps), Hi-Speed
(480Mbps), Full-Speed (12Mbps), and Low-Speed (1.5Mbps)
transfers supported on all ports
•Compact, steel, low-profile enclosure
•RoHS compliant
CHAPTER 3: HARDWARE
The USB3C-104-HUB is an industrial-grade 5-port USB hub
optimized for harsh and rugged environments. This hub has
latching / locking connectors on upstream and downstream ports as
well as a threaded locking power connection, preventing accidental
disconnects - making it ideal for high vibration applications. The
rugged steel enclosure, positive retention connections, and -40˚C to
+85˚C operation makes the USB3C-104-HUB stand out compared to
commercially available hubs, and it’s Made in the USA.
Each connection has been designed for rugged use without loose or
intermittent cables disrupting your application. The input power is
secured via screw terminals or a threaded DC Jack. Type C
connections utilize USB single screw locking standard cables
retained by the enclosure. The latching Type A ports’ connectors
themselves provide high-retention (50N) downstream connections
compatible with all industry-standard USB cables.
While USB has evolved, this card has enabled the maximum
functionality of USB by providing flexibility of power options using
USB PD 2.0 and USB 3.1 data transfer expansion in a single module
design.
This product is fully protected from faulty peripherals. Each port
(Non PD) utilizes a power distribution switch providing overcurrent
and short circuit protection. If a fault occurs, the power distribution
switch will disable that port and a warning will show in the operating
system. The disabled port can be re-enabled by clearing the fault
and cycling power to the port. PD ports utilize their own power
management circuitry for peripheral protection.
The boards are designed as PC/104 sized, with PC/104 mounting
holes, in a steel powder-coated enclosure with non-skid feet.
All units ship extended temperature and RoHS compliant.
INCLUDED IN YOUR PACKAGE
1× USB3C-104-HUB board
1× 3' USB 3.1 cable type C locking to type C locking (5A rating)
Available accessories include:
PWR-ACDC-24V10A-L
External Power Supply with locking
connector
LF-JDC-PLUG
Locking DC Power Plug w/sturdy back shell
and solder tabs
CAB-USBACL
6’ USB 3.1 type A to C cable w/single
screw lock
CAB-USB3CCLL
3’ PD 5A USBC locking to USBC locking
cable
MP104-DIN DIN rail mounting provision
Contact the factory for information regarding additional accessories,
options, and specials that may be available to best fit your specific
application requirements, such as conformal coating.
To take advantage of the Power Delivery (PD) feature on both the upstream port
to the host, and on the downstream PD port simultaneously, you’ll need to order a
CAB-USB3CCLL cable as a separate line item, as only one such cable is included
with the USB3C-104-HUB full version.

ACCES I/O Products, Inc. MADE IN THE USA USB3C-104-HUB Manual
3Rev B4d
CHAPTER 4: CONFIGURATION SETTINGS
All configuration of this device is performed through software; any jumpers or switches are for factory use only.
The latest information can always be found on the product page on the website.
Useful Links
https://accesio.com
accesio.com/USB3C-104-HUB
CHAPTER 5: SPECIFICATIONS
PC Interface
USB
USB 3.1 Gen 2
SuperSpeed+ (SS+/10Gbps), SuperSpeed (SS/5Gbps), Hi-Speed (HS/480Mbps), Full-speed
(FS/12Mbps), and Low-Speed (LS/1.5Mbps)
Environmental
Temperature
Operating
-40°C to +85°C
Storage
-40°C to +85°C
Humidity
5% to 95% RH, non-condensing
ESD Protection
+/-15kV IEC 61000-4-2 contact
+/-15kV IEC 61000-4-2 air
Dimensions
Board
PC/104 format and mounting holes
3.550 in by 3.775 in
w/Enclosure
3.985 in x 3.990 in x 1.045 in
Weight
Board
80 grams
w/Enclosure
302 grams
Power
Power required
External power from 20 to 26VDC is required. Screw
terminals are rated for wire sizes of 14-26 AWG, and are
rated for 15A.
Wattage of the power supply affects power delivery output. At 50W, PD is 3A
maximum, with 100W, PD is the full 5A specification.
Connectors
USB Type A
Latching
Retention up to 50 Newtons (retained by latch)
Physical shock: Per EIA-364-27 Condition H (11ms 30G)
Vibration: Per EIA-364-28D
Condition V, Test A
USB Type C
8 Newtons min, 20 Newtons max (insertion and
retention) without enclosure (-OEM version)
(retained by single screw lock in enclosure)
DC Jack (locking)
(MIL-STD-202G)
Vibration: Method 201A
Insertion Resistance: Method 302 Condition B
Thermal Shock: Method 107G
Model Options
-E
Non-locking version
-OEM
No enclosure (board only)
USB 3.1 vs USB 3.0
USB 3.0 was renamed to “USB 3.1 Gen 1” and operates at up to 5Gbps.
USB 3.1 Gen 2 supports 10Gbps

ACCES I/O Products, Inc. MADE IN THE USA USB3C-104-HUB Manual
4Rev B4d
CHAPTER 9: CERTIFICATIONS
CE & FCC
These devices are designed to meet all applicable EM interference
and emission standards. However, as they are intended for use
installed on motherboards, and inside the chassis of industrial
PCs, important care in the selection of PC and chassis is important
to achieve compliance for the computer as a whole.
UL & TUV
Neither DC voltages above 12V, nor AC voltages of any kind, are
consumed or produced during normal operation of this device.
This product is therefore exempt from any related safety
standards. Use it with confidence!
ROHS / LEAD-FREE STATEMENT
All models are produced in compliance with RoHS and various
other lead-free initiatives.
WARNING
A SINGLE STATIC DISCHARGE CAN DAMAGE YOUR CARD AND
CAUSE PREMATURE FAILURE! PLEASE FOLLOW ALL
REASONABLE PRECAUTIONS TO PREVENT A STATIC
DISCHARGE SUCH AS GROUNDING YOURSELF BY TOUCHING
ANY GROUNDED SURFACE PRIOR TO TOUCHING THE CARD.
ALWAYS CONNECT AND DISCONNECT YOUR FIELD CABLING
WITH THE COMPUTER POWER OFF. ALWAYS TURN
COMPUTER POWER OFF BEFORE INSTALLING A CARD.
CONNECTING AND DISCONNECTING CABLES, OR INSTALLING
CARDS, INTO A SYSTEM WITH THE COMPUTER OR FIELD
POWER ON MAY CAUSE DAMAGE TO THE I/O CARD AND
WILL VOID ALL WARRANTIES, IMPLIED OR EXPRESSED.
WARRANTY
Prior to shipment, ACCES equipment is thoroughly inspected and
tested to applicable specifications. However, should equipment
failure occur, ACCES assures its customers that prompt service
and support will be available. All equipment originally
manufactured by ACCES which is found to be defective will be
repaired or replaced subject to the following considerations:
GENERAL
Under this Warranty, liability of ACCES is limited to replacing,
repairing or issuing credit (at ACCES discretion) for any products
which are proved to be defective during the warranty period. In
no case is ACCES liable for consequential or special damage
arriving from use or misuse of our product. The customer is
responsible for all charges caused by modifications or additions to
ACCES equipment not approved in writing by ACCES or, if in
ACCES opinion the equipment has been subjected to abnormal
use. "Abnormal use" for purposes of this warranty is defined as
any use to which the equipment is exposed other than that use
specified or intended as evidenced by purchase or sales
representation. Other than the above, no other warranty,
expressed or implied, shall apply to any and all such equipment
furnished or sold by ACCES.
TERMS AND CONDITIONS
If a unit is suspected of failure, contact ACCES' Customer Service
department. Be prepared to give the unit model number, serial
number, and a description of the failure symptom(s). We may
suggest some simple tests to confirm the failure. We will assign a
Return Material Authorization (RMA) number which must appear
on the outer label of the return package. All units/components
should be properly packed for handling and returned with freight
prepaid to the ACCES designated Service Center, and will be
returned to the customer's/user's site freight prepaid and
invoiced.
COVERAGE
FIRST THREE YEARS: Returned unit/part will be repaired and/or
replaced at ACCES option with no charge for labor or parts not
excluded by warranty. Warranty commences with equipment
shipment.
FOLLOWING YEARS: Throughout your equipment's lifetime, ACCES
stands ready to provide on-site or in-plant service at reasonable
rates similar to those of other manufacturers in the industry.
EQUIPMENT NOT MANUFACTURED BY ACCES
Equipment provided but not manufactured by ACCES is warranted
and will be repaired according to the terms and conditions of the
respective equipment manufacturer's warranty.
DISCLAIMER
The information in this document is provided for reference only.
ACCES does not assume any liability arising out of the application
or use of the information or products described herein. This
document may contain or reference information and products
protected by copyrights or patents and does not convey any
license under the patent rights of ACCES, nor the rights of others.