Access Lighting 20351 User manual

CERTIFICATION: cULus WET NO. 20351
INSTALLATION INSTRUCTIONS
IMPORTANT
Before assembling your ACCESS LIGHTING fixture, please make
sure that you carefully read through this instruction sheet. Save this
instruction sheet and refer to it when additions to or changes in the
fixture configuration are made.
Enregistrer cette feuille d'instructions et de s'y référer lorsque les
ajouts ou changements dans la configuration de montage sont
faites
Consider having your fixture installed by a qualified licensed
electrician.
NOTE: The important safeguards and instructions that appear in
this manual are not meant to cover all possible conditions and
situations that may occur. It must be understood that common sense,
caution and care are factors that can’t be built into any product.
These factors must be supplied by the person(s) caring for and
operating the fixture
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances,
Local and National Electrical Codes. These fixtures are intended for
mounting to standard 4” x 2 ½” metal octagon outlet box. The box
must be directly supported by the building structure and U.L
Recognized
STEP-BY-STEP INSTRUCTIONS
Before starting your installation disconnect the Power by turning off
the Circuit Breaker or by removing the fuse at the fuse box. Just
turning the light off at the light switch is not sufficient to prevent
electrical shock.
APPLICATION
Indoor Wall Spotlight
MODEL NO.
20351
COLLECTION
KO
PREPARE FIXTURE
If there is an existing fixture remove it.
Expose the supply wires from the outlet
box. Screw the supplied crossbar to the
junction box using the supplied screws (1).
Gently pull the supply wires through the
center hole in the crossbar. Slide the fixture
wires through the hole in the back plate.
WHAT WE PROVIDE
Fixture Housing
Gasket
Back Plate
Crossbar
Cover
Mounting Hardware
1 x GU-10/35W
Bulbs
WHAT YOU NEED
Screwdriver
Wire Cutters
Wiring Supplies as
Specified by the
Electrical Code
1
1
Supply Wires from outlet box
Washers
IMPORTANT SAFETY INSTRUCTION
MESURES DE SECURITE A RESPECTURE
Consult a qualified electrician to ensure correct branch
circuit conductor.
Consulter un electricien qualifie pour vous assurer
que les conducteurs de la derivation sont adequats
This product must be installed in accordance with the
applicable installation code by a person familiar with
the contstruction and operation of the product and the
hazards involved.
Ce produit doit etre installe selon le code d’installation
pertinent, par une personne qui connait bien le produit
et son fonctionnement ainsi que les risques inherents
Do not install this fixture in hazardous locations.
N'installez pas cet appareil dans des emplacements
dangereux
Do not install fixture assembly closer than 6 inches from
any curtain or similar combustible material.
Laisser une distance d’au moins 6 pouces entre ce
luminaire et la toute surface combustible.
WARNING: Risk of Fire and Electric Shock
CAUTION: Risque d’ Incendie et de Choc Electriques

CERTIFICATION: cULus WET NO. 20351
CONNECT THE WIRES
Connect the black supply wire to the black fixture
wire. Secure with the supplied wire nuts. Connect
the white supply wires to the fixture wire. Secure
with the supplied wire nuts. Either wrap the outlet
box grounding (green) wire around the green
hexagonal screw provided on the mounting plate or
connect it to the supply ground wire provided with
the fixture. Secure all wires with U.L Certified
electrical tape (not supplied).
Tuck all wires carefully into the J-box.
2
MOUNT THE CANOPY
Since the application for this fixture is indoors, the
gaskets are not required and their use is optional.
Attach the back plate to the crossbar with the
supplied screws (3). Attach the fixture assembly to
the back plate by aligning the designated holes on
both the back plate and fixture assembly. Secure
with supplied screws (4).
Insert the supplied bulbs into the sockets.
Do not exceed the wattage stated on the warning label.
3
SECURE THE GLASS COVER
Fit the cover over the bulb and screw onto the
base to secure.
4
RESTORE THE ELECTRICITY AND
CHECK THE OPERATION OF
YOUR NEW ACCESS LIGHTING
FIXTURE
5
CAUTION
Please ensure that the fitting is cool and switched off
before replacing the bulb.DO NOT use bulbs that might
exceed the maximum wattage as stated on caution
label.
2