Access Security Products DJ4M User manual

DJ4M
User Manual
Audio Handset
Read this manual carefully before using the product, and keep it well for future use
2
ACCESS SECURITY PRODUCTS LTD

1. Parts and Functions
2
33
Side View
187
150
97
Handset
Call button/Unlock 2nd button
Speaker
handset curve
Unlock button
Handset Pick up to communicate with the visitor
Handset cord Connect receiver with handset base
Unlock button Press to release the door lock
Call button/Un-
lock 2nd button
In standby mode, pick up the receiver, then press Call
button to activate the inner call; (Intercom)
During calling/talking state, press Unlock 2nd button
to release the second door lock (If installed)
Speaker Receive audio from the visitor
Key functions
ACCESS SECURITY PRODUCTS LTD

2. Terminal Descriptions
L2 L1
SW+SW-
1 2 3 4 5 6
ON DIP
ON
1 2 3
K4
K3
K4
K3
DIP2
DIP1
L2 L1
SW+SW-
1 2 3 4 5 6
ON DIP
ON
1 2 3
K4
K3
SW+,SW-
L1, L2
SW+,SW-: External door bell connection port
L1,L2: Bus line connection
K4: To change ring tone setting
K3: To change ring tone volume
DIP1(Bit1-6): To set the User Code of each handset
DIP2(Bit1-3): To set Slave Handset Address
3. Unit Mounting
2
2
1) Fix 2 screws to the wall at an appropriate height
2) Connect the system correctly
3) Attach the audio phone to the bracket
ACCESS SECURITY PRODUCTS LTD

4. Operation Instructions
5. Setup Instructions
1) Door release function: When a visitor calls from the door panel, the handset rings,
pick up the receiver to talk with the visitor, then press the Unlock button to open the
door. If the system is connected with 2 lock releases, press Unlock 2nd button to open
the second door release
2) Inner call:(Intercom) Pick up the receiver, then press CALL button to activate
the inner call, all handsets connected to the system will ring at the same time. Pick up
any handset and the others will stop ringing immediately. (Note that the user code must
be the same for all handsets to activate the inner call function)
3) Door Bell Call Button:An additional door bell button can be connected to the
handset, so that the visitors can ring the door bell again in front of the user’s apartment
5.1 User Code Setting (DIP1 required)
Each apartment must have a unique identification called a User Code. The DIP1
switches are used to congure the User Code for each handset
• Bit-1-5 of DIP1 are used to create the User Code setting. The value is from 1 to 32,
which have 32 different codes for 32 apartments
• Bit-6 of DIP1 is used as an end of line termination
Note: DIP1 is NOT required with the single button audio entry system
Bit state User Code Bit state User Code Bit state User Code
1 2 3 4 5 6
ON
Code=1
1 2 3 4 5 6
ON
Code=12
1 2 3 4 5 6
ON
Code=23
1 2 3 4 5 6
ON
Code=2
1 2 3 4 5 6
ON
Code=13
1 2 3 4 5 6
ON
Code=24
1 2 3 4 5 6
ON
Code=3
1 2 3 4 5 6
ON
Code=14
1 2 3 4 5 6
ON
Code=25
1 2 3 4 5 6
ON
Code=4
1 2 3 4 5 6
ON
Code=15
1 2 3 4 5 6
ON
Code=26
1 2 3 4 5 6
ON
Code=5
1 2 3 4 5 6
ON
Code=16
1 2 3 4 5 6
ON
Code=27
ACCESS SECURITY PRODUCTS LTD

5.2 Slave Address Setting (DIP2 required)
When multi handsets are installed in one apartment, these handsets have to use the
same User Code setting, and the Master/Slave mode should be set on each handset
• Bit-1-2 of DIP2 are used to set the slave address setting
Bit state User Code Bit state User Code Bit state User Code
1 2 3 4 5 6
ON
Code=6
1 2 3 4 5 6
ON
Code=17
1 2 3 4 5 6
ON
Code=28
1 2 3 4 5 6
ON
Code=7
1 2 3 4 5 6
ON
Code=18
1 2 3 4 5 6
ON
Code=29
1 2 3 4 5 6
ON
Code=8
1 2 3 4 5 6
ON
Code=19
1 2 3 4 5 6
ON
Code=30
1 2 3 4 5 6
ON
Code=9
1 2 3 4 5 6
ON
Code=20
1 2 3 4 5 6
ON
Code=31
1 2 3 4 5 6
ON
Code=10
1 2 3 4 5 6
ON
Code=21
1 2 3 4 5 6
ON
Code=32
1 2 3 4 5 6
ON
Code=11
1 2 3 4 5 6
ON
Code=22
5.2.1 When Bit-3 of DIP2 set to OFF, the Bit-1-2 of DIP2 are used to set the master/
slave address setting:
DIP2 state Master/Slave type
1 2 3
ON
Master handset
1 2 3
ON
Slave handset 1
1 2 3
ON
Slave handset 2
1 2 3
ON
Slave handset 3
ACCESS SECURITY PRODUCTS LTD

5.3 Ring Tone Setting
There are four groups ring tones to choose from:
Group name Items Tunes
Group 1
Door Panel DINGDONG
Intercom Call TELEPHONE_RING
Door Bell DINGDONG
Group 2
Door Panel JINGLE_DELL
Intercom Call CARMAN
Door Bell FOR_ALICE
Group 3
Door Panel HAPPY_BIRTHDAY
Intercom Call SONATINE
Door Bell CONGRATULATE
Group 4
Door Panel DOREME
Intercom Call RHYTHM_OF_THE
Door Bell EDELWEISS
ACCESS SECURITY PRODUCTS LTD

2) Pick up the receiver in standby mode and press the K4 switch to replace a group of
ring tones. Four groups of ring tones cycle:
Group1 Group2 Group3 Group4
press K4 press K4 press K4
press K4
3) Put the receiver down to exit the settings
5.4 Ring tone Volume Setting
1) There are three kinds of ring tone volume (low-range, mid-range and high-range) to
choose from
2) Pick up the receiver in standby mode and press the K3 switch to adjust the volume
Low-range Mid-range High-range
press K3 press K3
press K3
3) Put the receiver down to exit the settings
6. Specication
●Power Supply: DC24V
●Power Consumption: standby 2.1mA, working 75.9mA
●Wiring: 2 wires, non-polarity
●Dimension: 187(H) X 97(W) X 33(D) mm
The design and specications can be changed without notice to the user. Right to interpret and copyright of this manual are preserved.
ACCESS SECURITY PRODUCTS LTD