Acclaim Lighting Dyna Accent User manual

www.acclaimlighting.com Dyna Accent
User guide

1
www.acclaimlighting.com
CONTENTS
INTRODUCTION ......................................................2
Welcome 2
Safety 2
Supplied items 3
Optional extras 3
INSTALLATION.........................................................4
Mounting 4
Pan and tilt adjustment 5
Tilt range 6
Fitting a spread lens 7
Fitting a snoot 8
Power and control wiring 9
Wireless control 11
OPERATION ........................................................... 12
Making a temporary control link with the XMT-350 12
Addressing fixtures 13
DMX channels 13
Configuring the Aria wireless DMX receiver 14
Using the automation features 15
Testing emitter output 16
FURTHER INFORMATION ......................................17
Troubleshooting 17
Optimizing signal strength via channel selection 18
Specifications 19
Limited product warranty 20

2www.acclaimlighting.com
INTRODUCTION
WELCOME
Welcome to the Dyna Accent range from Acclaim Lighting. These rugged LED-powered
fixtures are designed to replace traditional external flood lights while using a fraction of the
power. Featuring a die-cast aluminum body throughout with full IP66 environmental rating,
these fixtures are built to last. A choice of standard gray, black or white finishes plus special-
order custom colors are available.
The Dyna Accent range consists of four main variants:
•Fixed white - 2700K, 3000K, 3500K or 4000K emitters,
•DW (Dynamic White) - Warm and cool white emitters (2400K to 5500K),
•RGBW - Red, green, blue and cool white LED emitters,
•RGBA - Red, green, blue and amber LED emitters.
External control using the industry standard DMX-512A is supported via either cable or the
in-built Aria™ wireless receiver. The industry standard RDM (Remote Device Management)
format is used for configuration. Dyna Accent features automated operation when light
levels fall below a certain level together with a timer for auto shut off.
The internal auto-sensing power supply can accept mains inputs between 100 to 277VAC at
50 or 60Hz. Total power consumption is just 35W.
Optional spread lenses and snoots are available.
SAFETY
•When fixtures are mounted off-ground, ensure that they are securely fitted to an
appropriate mounting surface.
•Ensure that the power input is supplied from a correctly fused, earthed and
environmentally protected location.

3
www.acclaimlighting.com
SUPPLIED ITEMS
OPTIONAL EXTRAS
Dyna Accent
With integral mounting stand and 6 foot
(1.8m) power/control tails.
5mm Allen wrench
(hex key)
Silicone
gasket
Spread lens
20O, 40O, 60Oand 10Ox 60Oavailable
4” (100mm) Snoot

4www.acclaimlighting.com
Ø113mm
Ø109mm
63mm
63mm
15mm
INSTALLATION
MOUNTING
The base plate of the Dyna Accent can be directly
mounted onto a standard 4”round electrical outlet
box of sufficient strength for the weight of the fixture.
The data and power cables are fed through two glands
in the base plate so allowance should be made for
passage of the cables if mounted on a flat surface. You
should use screws/bolts with countersunk heads (less
than Ø7mm) in order to avoid interfering with the pan
rotation of the fixture.
Base pivot
point (oset
from center) Cable gland
4 x mounting
holes (Ø4mm)
with Ø7mm
recess on top
surface
The dimensions of the underside of the base are
shown below (at 75% of actual size):
Standard 4” round electrical outlet box (not supplied)
Silicone gasket
Note: It is important to use countersunk screws/bolts that fit flush within the countersunk
mounting holes as the rotatable base of the fixture overlaps the two rear holes.

5
www.acclaimlighting.com
PAN AND TILT ADJUSTMENT
To prevent any movement once set, the tilt adjustment uses interlocking teeth. This means
that you need to slacken the hex bolt completely before the teeth will disengage and allow
movement. A 5mm Allen wrench (hex key) is supplied with the fixture for adjusting the tilt
angle. A 2mm Allen wrench (not supplied) is required to adjust the pan angle using the two
small grub screws in the base.
5mm Allen
wrench
(supplied)
Tilt adjustment bolt
2mm Allen wrench
(not supplied)
Recessed pan
adjustment
screw x2
The tilt angle of the Dyna Accent head is adjustable through a range of nearly 180 degrees.
See next page .

6www.acclaimlighting.com
0
O
20
O
40
O
20
O
40
O
60O
80
O
100
O
120
O
140
O
0
O
20
O
40O
20
O
40
O
60
O
80
O
100
O
120
O
140O
0O
20
O
40
O
20
O
40
O
60
O
80O
100O
120
O
140
O
TILT RANGE
The head of the Dyna Accent can be rotated through almost 180 degrees (in 10 degree
increments), although the extremes of the range are only possible when the base plate is
mounted on the very edge of a surface. See the previous page for details about tilt (and
pan) adjustment.
0O
20
O
40
O
20
O
40
O
60O
80O
100O
120O
140
O
A handy rotation
scale is provided on
the leg of the fixture:

7
www.acclaimlighting.com
FITTING A SPREAD LENS
The standard beam angle is 6 degrees. This can be adjusted by inserting an appropriate
spread lens into the inside of the front panel.
TO FIT A SPREAD LENS
Notes: This operation is best achieved with the Dyna Accent front face lying horizontally. Install
spread lenses only in dry conditions to avoid any build up of condensation.
1 Using a 3mm Allen wrench (hex key), slightly loosen each of the four bolts that secure the
front hood to the main body of the fixture. Once all bolts have been suitably loosened,
remove all four of them plus their small washers and lift off the front hood.
2 Remove the protective films from both sides of the spread lens.
3 Ensure that the black rubber gasket is correctly in place around the circumference of the
spread lens. Find the Locating tab on one side of the rubber gasket and ensure that this
tab faces towards the front face of the Dyna Accent - and aligns with Locating notch in the
front face.
4 Place the front hood over the spread lens and Dyna Accent front face, ensuring that the
Drain hole of the front hood aligns with the drainage Recess in the rubber gasket of the lens.
5 Reintroduce the four bolts and their washers, and tighten sufficiently.
Spread lens
Front hood
Locating notch
Locating tab
Drain
hole
Recess

8www.acclaimlighting.com
FITTING A SNOOT
In installations where any light spill from the Dyna Accent must be eradicated from a nearby
surface, the optional 4”snoot is recommended.
Note: If required, a spread lens can be fitted together with the snoot, see page 7.
TO FIT A SNOOT
Note: This operation is best achieved with the Dyna Accent front face lying horizontal.
1 Using a 3mm Allen wrench (hex key), slightly loosen each of the four bolts that secure the
front hood to the main body of the fixture. Once all bolts have been suitably loosened,
remove all four of them plus their small washers and lift off the front hood.
2 Place the snoot over the Dyna Accent front face in replacement for the front hood. Note:
There are drain holes located every 90 degrees around the snoot circumference, so it can be
attached in any orientation.
3 Fit the four bolts and their washers from the original front hood, and tighten sufficiently.
Snoot