ACCO Brands Quartet Infinity User manual

Quartet Innity Glass Boards
4 x 6 , 4 x 8
6x
8x
4 x 6
4 x 8
4x8=8x
4x6=6x
4x8=8x
4x6=6x
4x8=8x
4x6=6x
4x8=8x
4x6=6x
4x8=8x
4x6=6x
4x8=8x
4x6=6x
4x8=16x
4x6=12x
1x
1x
4x8=8x
4x6=6x
4x8=8x
4x6=6x
4x8=8x
4x6=6x
7/32”
ACCO Brands (Returns Center)
101 Bolton Ave 9E
Booneville, MS 38829 USA
Tel: [phone]
www.acco.com
a
a
a
a
b
c
d
d
e
e
g
f
g
6
78
2
3 4 5
9 10
1
f
4x8=8x
4x6=6x
c
d
g
e
e
g
b
b

1x
1x
a
b
c
d
e
f
g
Innity Glass Board
Accessories Tray
Metal Threaded Stando Caps
Washers (2 Washers per Hole)
Phillips Head Screws
Self-Drilling Drywall Anchors
Metal Threaded Standos
Pencil
Level
Phillips Head Screwdriver
Power Drill
What’s Included in the Hardware Kit?
What Else Do I Need?
a
b
c
d
e
f
g
Quartet Innity Glass Boards
Extended Directions
Step 1– Prepare for Installation
Make sure you have enough people to install your board.
We recommend 3+ people for 72”x48” and 96”x 48”boards.
Place the Glass Whiteboard (Part A) against the wall in the desired installation location.
Place a level on top of the board to conrm it is level.
Use a pencil to mark an “x”in each mounting hole.
Extend the lines to the edge of the circle.
4x8=8x
4x6=6x
4x8=8x
4x6=6x
4x8=8x
4x6=6x
4x8=8x
4x6=6x
4x8=8x
4x6=6x
6x
8x
4 x 6
4 x 8
a a

Use a 7/32” drill bit to create the pilot hole.
Step 2-5 – Insert Wall Anchors
Carefully remove the glass whiteboard from the wall and place it in a safe spot.
7/32”
f
Insert a Self-Drilling Drywall Anchor (Part F) into each of the “x” marks
using a Phillips Head screwdriver. Turn clockwise until the head of each
anchor is ush with the wall.
Place a Stando (Part G) over each drywall anchor. Insert a Phillips Head Screw (Part E)
through the stando, into the anchor and tighten.
The screw should hold the stando tightly against the wall.
Repeat this process for all standos.
Make sure all standos are ush against the wall before proceeding.
Step 6 – Install Standos
g
e
e
g
g
e
4x8=8x
4x6=6x
4x8=8x
4x6=6x
4x8=8x
4x6=6x
4x8=8x
4x6=6x

Step 7-9 – Install Glass Board
c
d
d
g
Starting at an angle, press the Accessories Tray (Part B) up along the bottom of
the glass whiteboard.
Step 10 – Attach Accessory Tray
Place Washers (Part D) on the threaded section of each metal Stando Cap (Part C).
Lift glass whiteboard and align holes with the Standos (Part G) on your wall.
Once all washers are in place: Insert Stando Caps (Part C) through the
whiteboard and into the Barrels (Part G).
Turn caps clockwise until they are almost tight against the glass dry erase board.
Repeat steps for all standos.
Fully tighten Stando Caps once they are all in place.
Make sure the standos are ush against the board surface.
Push the tray up until the bottom of the back channel is fully against the glass.
The glass should t between the gap in the back channel of the tray.
4x8=8x
4x6=6x
b
b