Accurate Technology TWINSPIN REEL SR-20 Parts list manual

807 E. Parkridge Ave • Corona, CA 92879
1-888-ACCU-372 • 951-479-0909 • Fax: [phone]
www.accuratefishing.com

TWINSPIN RE E L
USAGE MANUAL

CONTENTS Features 1
Getting Acquainted 2
Operation 3
Drag Variance 3
Spool Assembely 4
Filling the spool 5
Rod Mounting 5
Line Capacities 6
Maintenance 7
Warranty 8
Preset

GETTING
ACQUAINTED
* The spool stud for tying the line to the spool it can be unscrewed to remove.
2
Preset
The
TWINSPIN preset has a
knurl lock in the center that is
used to take the spool off the
reel. Do not use the preset to
take the spool off.
Preset Lock
(knurled)
Cross Pin
Make sure spool locates
correctly on this pin when
re-installing the spool.
Left/Right Side Handle
The TwinSpin handle can be
used on the left or right side
of reel. Just unscrew handle
and cover and switch sides.
Handle Cover
Handle

Oil
Bearing Maintenance - The Class 5 A.B.E.C. bearings in the TWINSPIN are tephlon impregnated in the
ball bearing race; thus, no lubrication is needed for these bearings.
Wash down your TWINSPIN with fresh water after each use. We recommend lightly spraying it to prevent
water from being forced inside. Do not completely submerge the reel into water. Wipe the exterior parts
with an anti-corrosion lubricant. We recommend Corrosion X® by Corrosion Technologies. Use a good
quality reel oil to lubricate all the parts indicated with the oil symbol.
Periodically, check all exterior screws to make sure they are tight. Screws may loosen over time with
boat vibrations.
We recommend yearly maintenance of your TWINSPIN Reel with a service professional. Preventative
maintenance of your TWINSPIN Reel will keep the internal parts in proper working condition and prolong
the life of the reel.
MAINTENANCE
Water
7

WARRANTY
How Long Does The Limited Warranty Coverage Last? This limited warranty runs for a period of one (1) years starting from the date
that the TwinSpin reel was first purchased by the consumer. Coverage terminates if you sell or otherwise transfer the reel.
What Does The Limited Warranty Cover? Accurate Fishing Products warrants to the original purchaser that its TwinSpin fishing reels
are free from defects in material and workmanship with the exceptions stated below. Accurate Fishing Products will also, free of charge,
lubricate your TwinSpin reel one (1) time during the term of this Limited Warranty.
What Is Not Covered By This Limited Warranty? This limited warranty does not cover damage or problems caused by misuse, abuse,
neglect, accident, installation, alterations or failure to properly maintain the reel.
What Will Accurate Fishing Products Do? Accurate Fishing Products will repair or replace any reel which is defective in material or
workmanship covered by this limited warranty at no charge. Accurate Fishing Products will also, free of charge, lubricate your TwinSpin
reel one (1) time during the term of this Limited Warranty.
How Do You Get Service? If something goes wrong with your reel, or you want to receive the annual lubrication service, send it to
Accurate Fishing Products, postage pre-paid, along with a sales receipt or other proof of the date of purchase. Be sure to include a short
note explaining the problem. Send the TWINSPIN reel to Accurate Fishing Products at:
Accurate Fishing Products Warranty Repairs 807 E. Parkridge Avenue Corona, California 92879 1-888-ACCU-372
Please pack your reel with all parts that have been removed securely in a sturdy box. Be certain that your package is adequately
insured and mailed with a shipping company that has tracking capabilities. Be sure to include your name, address and telephone num-
ber. Accurate Fishing Products will inspect your reel and contact you within 30 days of receipt to inform you whether the problem is cov-
ered by this limited warranty. There is no charge for the inspection.
What Are The Warranty Limitations And Limitations Of Liability? There are no other express warranties. Any warranty of mer-
chantability or fitness for a particular purpose is limited to the duration of this limited warranty. Accurate Fishing Products shall NOT be
liable for any loss of use, loss of time, inconvenience, commercial loss, or other incidental or consequential damages. Some states do
not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the
above limitations and exclusions may not apply to you. This limited warranty gives you specific legal rights, you may have additional
rights which vary from state to state.
8
Accurate Fishing Products One Year Limited Warranty TwinSpin Reels

FEATURES THE TWINDRAG™SYSTEM
Traditional fishing reel design applies the drag pressure
to only one side of the spool — resulting in uneven
pressure placed on reel components and excessive
heat buildup. The TwinDrag™ system applies equal
pressure to both sides of the spool which distributes the
drag friction over the surface of two drag plates instead
of one. That’s 50% of the total drag pressure on each
side, resulting in a smoother drag with less heat build-
up and a balanced load on reel bearings and spool.
TwinDrag™ reels also have extremely accurate drag
settings with very little fluctuation. In fact, TwinSpin
reels will fluctuate less than 1-pound in total drag when
line is drawn at any speed. For example: when the drag
is set to 20 pounds on a TwinSpin reel, drag pressure
will only vary between 19.5 and 20.5 pounds, or less!
• Patented TwinDrag™ system
• Machined Billet 6061 T6 aluminum
- Body, Frame, Rotor, Spool
• 14 Class-5 ABEC stainless steel bearings
• Preset with identification marks
• Titanium drag friction washers
• Removable spool stud
• AccuDrags
• Stainless-steel gears, springs & screws
• Power knob - Ergonomic designed
for comfort and a sure grip
• 1-year warranty
• AccuCare reel service
• Proudly designed and manufactured
in the USA
1
EVEN DRAG PRESSURE
Drag pressure
Drag pressure

4
SPOOL
ASSEMBELY
CARBON FIBER
TITANIUM FRICTION WASHER
.035”
Thick
.040”
Thick
SPOOL SHIMS
These shims are used to
move the position of the
spool for proper line lay.

Begin filling the TWINSPIN Reel by attaching the line securely to the reel spool. With tension applied to the line, fill the spool to
approximately 1/4” from the spool edge. .
Because of mono compaction when using ultra light line, we recommend first filling the spool with at least 2/3 dacron line.
Mono Compaction - Mono compaction is a problem that happens with light line. The smaller the mono line diameter, the more elas-
ticity the line will have. The elasticity is multiplied by the amount of line put on the spool which creates pressure
on the spool. When too much light line is added, the pressure can expand the spool. This could cause the reel to perform with
inconsistent drag pressure or, if enough pressure is built up, break the spool in half. Always put the least amount of ultra-light line
on the reel as needed.
FILLING
THE SPOOL
ROD
MOUNTING
Mount the reel to a rod with an aluminum or
re-inforced reel seat. Make sure the reel base
is securely clamped down in the reel seat.
Check to see if the reel moves in the reel
seat.
5
Reel Seat
Reel Base

LINE CAPACITY SPECTRA LINE CAPACITY
MODEL WEIGHT GEAR RATIOS lbs./line dia. inches/yds. lbs./yds
SR-20
SR-30 32.5 oz. 6:1 30/.022/325 65/500
SR-30 L 32.5 oz. 4:1 30/.022/325 65/500
LINE
CAPACITIES
6
Coming Soon
Coming Soon

DRAG
VARIANCE
Thanks to the TWINSPIN exclusive Twin Drag technology, the drag tension you set will vary no more than two pounds when line is
pulled off the reel at any speed! Unfortunately, there is another factor which causes drag variance that needs to be accounted for. This
factor is based on how full the reel is with line. When the spool is filled, the line is being pulled off a high point on the spool. As the
amount of line on the spool reduces, the line is pulled from a lower area on the spool. There is less leverage used when the line is
pulled at a lower level, which means the line needs more force to move the spool against the drag. The drag setting has not been
decreased, but the line will encounter increased tension. Account for the drag pressure to approximately double when 25% of the line
has been removed from a full spool.
OPERATION Basic operation of your TWINSPIN Reel is no different from operating any other spinning reel except for setting the preset drag. Once
the spool is filled with line you can set the preset drag. First test the drag pressure with the preset tuned to a light drag
pressure (counter clockwise). Turn the preset clockwise until you reach your desired drag pressure. Standard
practice is to set the drag pressure at approximately 30% of your line strength. We have lasered lines around
the spool cover to give you a reference when turning the preset.
Make sure to keep the rubber washer on the preset well lubricated. If it is dry it will move with the spool when
line is pulled off the reel in drag mode.
Removing the Spool - Turn the preset lock counter-clockwise to remove the spool. Do not turn the preset
to remove the spool only turn the preset lock. Pull the spool off the spool shaft. When putting the spool back
onto the reel make sure to turn the spool slightly to align it with the cross pin on the spool shaft.
3
Rubber
Washer
Reference
Marks
Preset
Lock