AccuTemp STX-AT-EK User manual

STX Accu-Temp
Electric Kettle
Instructions
Accu-Temp
Cordless Electric Kettle

- 1 -
PARTS
SPECIFICATIONS
Model STX-AT-EK
Power Supply 110/120 V, 60 Hz
Capacity 1.8 Liters
Net Weight 2.8 lbs..
Overall Dimensions (L x W x H) 8.5” x 8.5” x 10.4”
Control System Strix Technology*
*All Strix controls are designed to meet all relevant international standards
and approvals and are manufactured to consistenly exceed 12,000 cycles of
normal operation.
Lid
Base
Kettle
Spout Lid Release
Button
Water Level
WIndow
Temperature
Selection
Buttons
Handle

- 2 -
IMPORTANT SAFEGUARDS
Basic safety procedures should be used whenever using any electrical appliance.
Please read and understand all instructions prior to using this product.
FOR HOUSEHOLD USE ONLY.
ALWAYS USE HANDLE.
KETTLE SURFACE WILL BE HOT TO TOUCH.
FOR YOUR SAFETY AND OPTIMAL PERFORMANCE PLEASE READ
• Always use the kettle handle during operation. Kettle surface will be
very hot during use and initially during cooling. Scalding could occur.
• Use 120V power source.
• Keep out of the reach of children. Do not leave this devise
unattended when in use.
• To avoid electrical shock, DO NOT IMMERSE CORD, PLUG,
OR BASE UNIT IN WATER or other liquids. Do not operate this
appliance with wet hands or near standing water.
• Always check the condition of the power cord and plug. If there is
any evidence of a damaged or fraying cord, or if the appliance has
malfunctioned, or if the appliance has been damaged, discontinue
use and contact STX International (See CONTACT INFORMATION).
• Do not allow the power cord to hang over the edge of a table or
counter.
• Not intended for outdoor use.
• Do not place the kettle near or on a hot gas or electric burner, or in a
heated oven.
• Only use the power base provided with the appliance. The use
of accessory attachments is not recommended and will void all
guarantee/warranties.
• Do not use appliance for other than intended use.
• Always use this appliance on a level surface.
• Do not overfill the kettle.
• Pour hot liquids slowly and carefully. Do not over tilt the kettle.

- 3 -
WARNING!
Risk of Fire or Electric Shock
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: SHOCK HAZARD - DO NOT OPEN
Within the product enclosure there is uninsulated dangerous voltage
that may be of sufficient magnitude to constitute a risk of fire or
electric shock to persons.
• It is not recommended to open the lid while the water is heating or
boiling. Scalding may occur if the lid is opened during the heating
cycle.
• Always ensure that the kettle is turned off before cleaning or after
use and prior to unplugging from the wall outlet. Ensure that this
appliance is turned off and disconnected from any power source
when not in use.
• Do not use in dusty conditions.
• Avoid use near strong magnets or strong electrical currents.
• Do not drop the kettle.
• Do not attempt to repair, open or alter any components without
the written approval of STX International (See CONTACT
INFORMATION). Any attempt to repair or modify this product without
the approval STX International will void all guarantee/warranties.
• Do not operate this appliance in an appliance garage or under a
wall cabinet. When storing this appliance in an appliance garage or
under a wall cabinet, always unplug the unit from any power source.
Not doing so will increase the risk of a fire. Ensure that the stored
appliance is not in contact with the walls of a cabinet or appliance
garage.
• Ensure that the kettle is kept clean. Please read the Cleaning –
Storage – Decalcifying instructions in this manual.

- 4 -
GETTING STARTED
1. Remove any packaging material and promotional labels before using
your electric kettle for the first time.
2. Read and understand the Owner’s Manual prior to using this
appliance.
3. It is recommended that you retain the packaging materials in the
event that any future shipping of this appliance is necessary.
4. The manufacturer recommends that prior to usage you fill the kettle
to the maximum level with water, bring to a boil and then discard all
of the water. This will sanitize the unit before usage.
NOTE: This appliance is designed for boiling drinking water only; never
use it to heat or boil any other liquids or foodstuffs. The lid
should always be firmly in place and locked closed before use.
1. 6 Temperature Settings
160°F, 175°F, 180°F, 190°F, 200°F, 212°F
2. 1.8 Liter (7.6 cups) Capacity
3. Stainless Steel Construction
4. Concealed Heating Element
5. Boil Dry Protection
6. Automatic Shut Off
7. Enhanced Keep Warm Function
8. Cord Storage
9. Removable Filter
10. Cordless Kettle
11. 360° Rotating Base
12. BPA-Free Plastic Water Lelvel Window
(all parts that come in contact with water are BPA-Free)
13. Anti-Drip Design Spout
14. Strix Heating Element
FEATURES

- 5 -
CLEANING & STORAGE
1. Always ensure that the base unit is turned off, unplugged from the
wall outlet, and that the kettle has cooled sufficiently to touch prior to
any cleaning or storage. Wipe down the exterior of the kettle with a
moist cloth.
2. When storing, stow the cord beneath the base unit and make sure
that the lid is closed and that the kettle is correctly attached to the
base. Do not place anything on top of the kettle during storage.
3. Periodically it may be necessary to remove mineral deposits that
build up. These deposits are associated with the mineral content of
tap water and therefore how often you will need to “descale” your
kettle will depend on the level of calcium in your water supply. This
calcium build up may look like a discoloration on the inside of the
kettle.
4. To remove mineral deposits you can purchase kettle descaler
products from most supermarkets or hardware stores and follow the
directions on the packaging.
HOME DECALCIFYING
To home decalcify, open the kettle lid and fill with 3 cups of white vinegar
and add water to the maximum level. Bring to boil. Once the solution is
boiling turn off the kettle and unplug base. Let it sit for 20 minutes and
then pour out. Rinse the kettle. You may need to rinse the kettle several
times so there is no trace of vinegar in the kettle.
Remove the solution the following day, refill with fresh water and bring to
a boil. Then discard the water. Repeat as necessary to remove any build
up.
OPERATING INSTRUCTIONS
POSITIONING THE KETTLE
1. Ensure that the kettle base is positioned on a safe, level, and stable
work area.
2. Remove as much of the power cord from the underside of the power
base (cable storage area) as necessary to connect to a wall outlet.
3. Ensure that the power cable does not extend over the work area.

- 6 -
4. Always Keep out of reach of children.
5. Keep base away from any flammable materials.
6. After pouring hot water, return the hot kettle to the base or a suitable
heat resistant or heat protected surface.
FILLING THE KETTLE
1. Always remove the kettle from the base before adding water.
2. Open the lid by pressing the lid button on the handle.
3. Never add water while the kettle is positioned directly above the
heating element.
4. Add fresh, cold water. Never add any liquid other than water. The
water level should be greater than the minimal level (approximately
3.5 cups or .8 Liters), but not to exceed the maximum level (7.6 cups
or 1.8 Liters).
5. Push the lid closed until it locks into position.
6. Place the kettle on the power base. Plug the base into an electrical
outlet. The base will beep twice.
NOTES:
• Use deionized/purified water when possible for best taste and to
minimize mineral build-up in the kettle.
• Remove any residual water from the kettle’s outside housing prior
to placing the kettle on the base.
• Do not fill above Maximum Level indicator.
REGULAR HEATING MODE
The Regular Heating Mode is designed to heat the kettle to the desired
temperature and once the designated temperature has been reached,
the LED light on the base will turn off and the base will automatically turn
off.
1. Select the desired setting by pressing one of the six buttons.
2. The base will beep once and the selected button LED will turn red.

- 7 -
3. Once the temperature has been achieved the base will beep 5 times,
the base heating element will automatically turn off, and the red LED
will turn off.
4. Whenever you remove the kettle from the plugged-in base it will turn
off. This is a safety feature to eliminate the potential for electrical
shock or fire with an exposed hot base.
NOTES:
• You can cancel the selected temperature at any time by pressing
the selected temperature button again. This will shut off the base.
• Fog and condensation will appear in lid and water level view, this is
typical.
• You cannot select a lower temperature once the kettle has heated
to a designated setting until after it has had time to cool down.
• Whenheatingwatertothehighesttemperature(212˚F),thekettle
may vibrate slightly on the base. This is expected.
KEEP WARM MODE
The Enhanced Keep Warm Mode is designed to allow the kettle to
maintain a designated temperature for up to 30 minutes. During this
mode, each time the kettle is removed and replaced, the kettle will be
reheated to the designated temperature. During this mode the kettle
base will beep for 10 seconds each time the kettle is removed from the
base and beep once when it is replaced. It will automatically reheat to
the designated temperature. This mode will be maintained for up to 30
minutes. After approximately 30 minutes the base will automatically turn
off.
1. Fill the kettle as directed (see FILLING THE KETTLE).
2. Place the kettle on the base.
3. Select the desired setting by pressing AND HOLDING one of the six
buttons for 3 seconds. It will beep three times and the button LED
will light up red while the kettle is heating. Once the kettle reaches
the designated temperature, the kettle will beep once and the LED
will change to blinking blue to indicate the Enhanced Keep Warm
Mode is functioning.

- 8 -
4. When the kettle is removed from the base, the base will turn off.
Once the kettle is placed back on the base, you can select the
desired setting again and the blue light will illuminate and start
blinking again. This reactivates the enhanced keep warm mode. The
kettle will then reheat to the designated temperature if necessary.
This function will continue for up to 30 minutes.
5. To turn off the unit, press the blinking button.
BOIL DRY PROTECTION
As a safety feature, this kettle is designed to automatically turn off when
insufficient water has been kept in the kettle. This feature is designed to
prevent overheating of the appliance. When this feature is triggered the
unit is designed to shut off. To reset the unit, unplug the unit from the wall
outlet. Allow the kettle to cool completely. Once the kettle has cooled,
refill the kettle to the correct level with water and plug the unit back into
the wall socket. The safety boil dry protection will automatically reset.
FILTER
The kettle has a removable filter just inside the lid by the spout. The filter
can be removed to clean with hot water and soap. Do not run the filter
through the dishwasher.
To properly insert the filter, place the filter in as shown in the picture
below.

- 9 -
TEA HEATING & STEEPING
RECOMMENDATIONS
(Individual taste and preference may differ)
160°F 175°F 180°F 190°F 200°F 212°F
Delicate
Tea
Green
Tea
White
Tea
Oolong
Teas
Coffe &
Other Teas
Black
Tea
1-2 min 2-3 min 2-3 min 3-4 min 4-5 min 3-5 min
White Tea Arabian
Night
Asatsuya
Bancha
Ceylon
Green
Chin Chun
Mee
Darjelling
Green
Dragon
Well
Fukamushi
Gyokuro
Jasmine
Kukicha
Nepal
Green
Peah
Pi Lo Chun
Sencha
Shincha
Souchong
Apple
Black
Cherry
Blackcurrant
China Yin
Zhen
Coconut
Elderflower
Ginger
Lemon
Lychee
Mango
Orange
Peony
Snowbird
Strawberry
Most
Varieties
Instant
Coffe
Pressed
Coffee
Ceylon
China
Lapsang
China
Rose
Darjelling
Earl Grey
English
Breakfast
Indian Chai
Irish
Breakfast
Keemun
Orange
Pekoe
Russian
Samovar
Vanilla
Assam
Bagged Tea
Chai
Chamomile
Chinnamon
Golden
Yunnan
Herbal
KEnya
Lapsang
Souchong
Lemongrass
Peppermint
Red
Rooibos
Spearmint
Whole Leaf

- 10 -
SAFETY INSTRUCTIONS
1. Please read all instructions prior to operating this appliance.
Please keep this manual for future reference. Failure to comply with
the safety instructions and/or operating instructions contained in this
manual will void any warranty. The manufacturer/seller accepts no
liability for damages caused by failure to comply with the owner’s
manual or negligent use of this product.
2. Check for damaged parts prior to use. check that all parts are
operating properly and perform their intended functions.
3. Always check the condition of the power cord prior to use. If there is
any evidence of damage or fraying of the power cord discontinue use
and contact STX International for OEM replacement. (see Contact
Information on the back of this manual) STX International will only
use original OEM parts when/if replacement is necessary.
4. Always disconnect the unit from the power source before servicing
or cleaning the unit. Unplug the unit when not in use. Do not plug the
unit into an already damaged outlet.
5. This product is designed for indoor household use only. It is NOT
a commercial use product. Do NOT use for commercial industrial
purposes.
6. Do NOT operate outdoors or near any flammable or combustible
materials. Do NOT use during eletrical storms.
7. Keep out of the reach of children. Never leave this device
unattended.
8. It is important to monitor this product while in use. Do not leave this
unit unattended when plugged into an outlet or powered ON.
9. To prevent electric shock and damage to the unit, do NOT imerse the
main unit in water.
10. Do not operate this unit near an open flame or any hot surface.

11. Do not unplug the unit by pulling on the electrical cord itself. Never
unplug the unit with wet hands.
12. Always use 110/120 Volt power sources. DO NOT USE POWER
CONVERTERS (210/220V).
13. Do not plug another high wattage appliance into the same outlet as
this product.
14. Do NOT operate under the influence of alcohol or drugs.
15. Any alteration of this unit’s components, substitution of other
manufacturer’s components to this unit, or any repairs to this grinder
not completed or authorized by STX International will immediately
void all guarantees/warranties.
16. Electrical repair or any other type of service must be done by
the seller (The Mercantile Station 2 / STX International). Proof of
purchase must be provided by consumer prior to any repair/service
acceptance. The seller will use only OEM parts and accessories.

All STX International Products come with a 3-Year Guarantee, valid only
in the 48 Contiguous United States. If you purchase this product and ship
it to a destination outside of the 48 Contiguous United States this warranty
becomes null and void.
The first 30 Days are covered by a Money Back or Replacement
Guarantee from the date of the receipt of the product. If your product
becomes damaged in shipment or is found to be defective in any way
during this period, we will replace or issue a complete refund for your
product upon return. We will pay all shipping involved during this first 30-
day period.
The remainder of the 3 Years (after the first 30 days) is covered by a
FREE REPAIR Guarantee (parts and labor included). If anything becomes
defective during this period we will fix the issue and provide a full service
inspection to your product, shipping (to & from) will be paid by the buyer.
Please email us at [email protected] to set up a service request.
Returns of New/Unused Products
If you have Buyer's Remorse and decide that you do not want the product,
it must be returned NEW & UNUSED in the original box and you will pay
the return shipping. PLEASE NOTE: There will be a 10% Restocking Fee
and original Shipping Costs (if applicable) will not be refunded. Used
product cannot be returned.
3-YEAR
WARRANTY
                 




























STX International
2159 Magnum Circle, Lincoln, NE 68522
[email protected] •www.STXInternational.com
How To Register Your Warranty
Go to www.STXInternational.com. Click on "Register Your Warranty" tab
and fill out the form. This is a fully secure website. Your information will
never be sold or misused in any way. This registration site is strictly for
order verification that will be used to speed up the process should you
ever need to use your Warranty for service.
                 





























QUESTIONS, PROBLEMS
OR COMPLIMENTS?
Thank You for purchasing this
STX International Product!
We are grateful for your business!
All of our STX International Products are inspected then
sealed with our NEW Product Seal prior to shipment.
Our goal is to ensure Quality, Completeness, and
Satisfaction for your order.
For Any Questions, Problems, or
Compliments please call or email us.
If you would like to shop for other STX International Products
Please visit our website
www.STXInternational.com
Toll Free: 844-861-4762
[email protected]
Our Business Hours are:
Monday - Thursday: 8am - 4pm CST
Friday: 8am - Noon CST


STX International
2159 Magnum Circle, Lincoln, NE 68522
[email protected] •www.STXInternational.com