Acer B223W - Bdmr - 22" LCD Monitor User manual

Acer Acer –LCD-B223W
- 0 -
Service Manual
LCD MonitorAcer B223W

1
1
Table of Contents
Important Safety Notice .........................................................................................01
01 Product Specification ..........................................................................................03
02 Flat Panel Specification .......................................................................................18
03 Exploded Diagram ..............................................................................................37
04 Troubleshooting ....................................................................................................39
05 Spare Parts List ...................................................................................................44
06 Schematics and Layouts.......................................................................................45
07 Assembly and Disassembly ................................................................................48
Appendix : User’s manual
Copyright
Copyright 2006 InnoLux Tech. Corp. Ltd
All Rights Reserved
This manual may not, in whole or in part, be copied, Photocopied, reproduced, translated, or converted to any
electronic or machine readable form without prior written permission of InnoLux Tech. Corp. Ltd.
Acer B223W Service Manual

Acer Acer –LCD-B223W
2
Important Safety Notice
1. Safety precautions
This monitor is manufactured and tested on a ground principle that a user’s safety comes first.
However, improper used or installation may cause damage to the monitor as well as to the user.
Warning:
zThis monitor should be operated only at the correct power sources indicated on the label on the
rear of the monitor. If you’re unsure of the power supply in you residence, consult your local dealer
or Power Company.
zDo not try to repair the monitor by yourself, as it contains no user-serviceable parts. This monitor
should only be repaired by a qualified technician.
zDo not remove the monitor cabinet. There are high-voltage parts inside that may cause electric
shock to human bodies.
zStop using the monitor if the cabinet is damaged. Have it checked by a service technician.
zPut your monitor only in a lean, cool, dry environment. If it gets wet, unplug the power cable
immediately and consult your closed dealer.
zAlways unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth. Apply
non-ammonia based cleaner onto the cloth, not directly onto the class screen.
zDo not place heavy objects on the monitor or power cord.
2. Product safety notice
Many electrical and mechanical parts in this chassis have special safety visual inspections and the
protection afforded by them cannot necessarily be obtained by using replacement components rated
for higher voltage, wattage, etc. Before replacing any of these components read the parts list in this
manual carefully. The use of substitute replacement parts, which do not have the same safety
characteristics as specified in the parts list, may create shock, fire, or other hazards.
3. Service notes
zWhen replacing parts or circuit boards, clamp the lead wires around terminals before soldering.
zKeep wires away from high voltage, high temperature components and sharp edges.
zKeep wires in their original position so as to reduce interference.
zAdjustment of this product please refers to the user’ manual.

Acer Acer –LCD-B223W
3
01 Product Specification
1. General:
BV223W series LCD monitor is designed with a wide screen 22.0” WSXGA+ TFT LCD panel, LVDS interface, Analog RGB
signal input.
It featured with embedded universal AC power supply. This monitor can support maximum resolution up to 1680 x
1050@60Hz.
Details in this document DVI referred to is an option function depending on client’s requirement. In our factory, products
should be distinguished by module names.
1.1 Main Features
Maximum resolution : 1680 x 1050 @ 60Hz
Back light system : 4 CCFL (top & bottom edge side)
Pixel pitch : 0.282 (H) x 0.282 (V)
Display area : 473.76(H)x296.1(V) 22.0 inch diagonal
Brightness : ≥250cd/m²
Contrast ratio : 1000׃1 (typ.) (1)
Response time (Tr+Tf) : 5ms (typ.) (2)
Viewing angle : 160°(H)/ 160°(V), typ (3)
Input interface : Analog (D-sub 15 pin)
Digital Option(DVI-D 24 pin)
Power management : Compatible with VESA DPMS
Plug & Play : VESA DDCCI
OSD language : English, French, Spanish, Italian, Deutsch, Simplified Chinese,
Traditional Chinese, Japanese (Dutch, Finnish, Russian depend on sale region)
Universal AC power supply
Note (1)(2)(3): This item spec depend on the LCD panel.
1.2 Accessories
AC Power Cord : 1.8 m. (Black. Cord type depend on sale region)
VGA cable : 1.8 m. (15 pin D-SUB, black cable with blue male connector)
User manual : English (640Mb CD)
Warranty card
DVI cable (option) : 1.8 m. (18+1 pin, black cable with white connector)
2. Operation Specifications
The unit should suffer no visible cosmetic damage and should operate with no degradation in display quality during
exposure to the operating conditions and after exposure to the non-operating conditions, in any sequence.
2.1.1 Operating:
Temperature range : 0°C to 40°C
Relative humidity : 20% to 90%
2.1.2 Storage note 1:
Temperature range : -20°C to 60°C
Humidity range : 10% to 90%
2.1.3 Altitude
note 2
Operating 10000 ft (Ta=50, t=24h)
Storage 40000 ft (Ta=30, t=24h )
Note 1: Temperature and relative humidity range must be in the area shown as the following figure due to panel limited

Acer Acer –LCD-B223W
4
Note 2: Altitude spec must not over panel spec.
Figure 1 Absolute Ratings of Environment
2.1 Safety, EMC, Ergonomics and Compatibility Requirements
Safety & EMC
cUL, UL, CE, CB, CCC, TUV/GS, TUV/EGO,
TUV/ISO-13406-2, C-Tick (N214), VCCI, FCC, CE, CCC,
BSMI, C-Tick
Ergonomics TCO99, TCO03
Compatibility Windows 98/Me/2000, Windows XP, Window Vista
Power Management Energy Star V4
2.2 Electrostatic Discharge Requirements
The subject unit must withstand ±8KV for contact discharge and ±15KV for air discharge of Electrostatic Discharge and
meet the standard of IEC61000-4-2(EN55024). (without discharge on VGA/DVI/HDMI pin)
2.3 Reliability
The MTBF of this product shall be greater than 40,000 hours excluding the LCD panel. The LCD panel life which is
defined as the time period for the maximum luminance to reduce to 50% of the initial value is 40,000 hours minimum at
the condition of displaying an all WHITE field at mid Brightness and Contrast settings.
3. Electrical and Optical Characteristics and Performance
3.1 Backlight Power Supply
3.1.1 AC Input Voltage Range
It is a universal type and the input voltage range is from 100 ~ 240Vrms
3.1.2 AC Input Current
1.2A (max) at 100VAC input
0.6A (max) at 240VAC input
3.1.3 AC Frequency Range
The frequency range is from 50Hz to 60Hz
3.1.4 Inrush Current
a. 40A max at cold-start, 25°C, DC output full-loading and 100Vac input
b. 60A max at cold-start, 25°C, DC output full-loading and 240Vac input
Notes: 1. Before each test, the buck capacitor need to be discharged.
2. Before each test, it must be 10 minutes at least after the latest test.
3.1.5 Regulator Efficiency≥75%

Acer Acer –LCD-B223W
5
(DC output full loading and nominal AC input voltage range)
3.1.6 Ripple and Noise
Total composite ripple and noise less than 320mV for +16V output, and less than 150mV for +5V output, and 50mV for
+3.3V output tested by DC loading side parallel with a 47uF/EC and 0.1uF/Ceramic. Capacitors and measured band-width
with DC-20MHz
3.1.7 DC Output Voltage and Current
Current
DC Output Voltage Typ. Max.
VCC16V 15.2V-18.5V 1.8A 2.2 A
VCC5V 4.75~5.25V 1.5A 1.8A
Note: For the normal loading test ,the output loading use typical current.
3.1.8 Protection
a. SCP: For short circuited protection and with auto-recovery function.(for 5V output it must be shorted before F802)
b. OPP: Over-power protection, Range: 60W ( min ) on nominal AC input.
c. BOP: Brown Out protection
Condition: Pattern: Dot pattern,
Timing: 1680x1050 60Hz,
Brightness: Max.
Contrast: Max
Spec: system shutdown voltage must be > 50V
system restart voltage must be <85V
3.1.9 Power consumption
Max. 55W.
Follow Energy Star V4 condition 49W
3.1.10 Power management
BV223W supports Energy Star V4 and VESA DPMS
Status H-sync V-sync Video Power LED
On Mode/Active Power on on active ≤55W Blue
off on blanked < 2W Orange
on off blanked < 2W Orange
Sleep Mode/Low Power
off off blanked < 2W Orange
Off Mode/Standby Power -- -- -- < 1W Off
3.2Backlight
Item Symbol Min. Typ. Max. Unit Remark
Input Voltage Vin 15.2 16.0 18.5 V
Von 2.0 3.3 5.5 V
Enable (On/Off) Voff -0.3 --- 0.8 V
Kick off Voltage:
Item Symbol Min. Typ. Max. Unit Remark
Kick off Voltage Vs 1700 --- --- Vrms

Acer Acer –LCD-B223W
6
On Load Function:
Item Symbol Min. Typ. Max. Unit Remark
Input Current Iin --- 1.8 2.2
A
Frequency F 40.0 45.0 80 kHz @Max-Load
Output Current for
One Lamp IL3.0 7.0 8.0 mArms
PWM dimming control
mode: 2mA≤IL≤8mA
Operating Voltage Vo --- 750 --- Vrms
Brightness PWM
duty 35% --- 100%
Kick Off Voltage
Hold Up Time T 1.0 1.5 --- S
@Vin=16.0V
Brightness=3.3V
Efficiency η75% --- ---
@Vin=16.0V
Brightness=3.3V
3.3 Brightness output
The test to verify specifications in this section shall be performed under the following standard conditions unless
otherwise noted.
Temperature : 25 ± 5°C
Test pattern : white
Video Resolution : 1680 x 1050
Video input level : 700 mV ± 2%
Warm-up time : 30 minutes
Set brightness control and also contrast control at maximum, to measure the screen center, the light output
shall ≥250 cd/m2 (as panel spec)
3.4 White balance
The test standard conditions refer to Sec 3.3.(Brightness control is at 100 contrast control is at 50 )
Chromaticity Coordinate
Mode x y
Cool 9300K 0.283 ± 0.030 0.297 ± 0.030
Warm 6500K 0.313 ± 0.030 0.329 ± 0.030
User Panel While x Panel While y
3.5 Brightness uniformity
The test standard conditions refer to Sec 3.4.
%
≥75
)(backlightpointsnineofluminanceMax.
)(backlightpointsnineofluminanceMin.

Acer Acer –LCD-B223W
7
4. Input / Output Signal Specifications
4.1 Video signals
Analog RGB signal: 0.7Vp-p (Input impedance = 75 Ohm)
Sync: TTL level (Input impedance ≧1k Ohm)
Positive and negative sync of Separate Horizontal/Vertical Sync
Digital : TMDS Signal: (min) ±200mVpp@24Bit
4.2 Signal Timing
Through D-SUB/DVI connectors, this unit can support FH= 31.5~84 KHz, Fv=56~76Hz, with maximum
pixel clock 165MHz input signal and WSXGA+ output. Modes details as below:
VESA MODES
Horizontal Vertical
Mode Resolution Total Nominal
Frequency
+/-0.5KHz
Sync
Polarity
Nominal
Frequency
+/-1Hz
Sync
Polarity
Nominal
Pixel Clock
(MHz)
640*480@60Hz 31.469 N 59.941 N 25.175
640*480@72Hz 37.861 N 72.809 N 31.500
VGA
640*480@75Hz 37.500 N 75.000 N 31.500
800*600@56Hz 35.156 P 56.250 P 36.000
800*600@60Hz 37.879 P 60.317 P 40.000
800*600@72Hz 48.077 P 72.188 P 50.000
SVGA
800*600@75Hz 46.875 P 75.000 P 49.500
1024*768@60Hz 48.363 N 60.004 N 65.000
1024*768@70Hz 56.476 N 70.069 N 75.000
XGA
1024*768@75Hz 60.023 P 75.029 P 78.750
1152*864@75Hz 67.500 P 75.000 P 108.000
1280*960@60Hz 60.000 P 60.000 P 108.000
1152*720@60Hz 44.859 N 59.972 P 66.750
1280*1024@60Hz 63.981 P 60.020 P 108.000
SXGA 1280*1024@75Hz 79.976 P 75.025 P 135.000
SXGA+ 1400x1050@60Hz 65.317 N 59.978 N 121.75
1 2
5
7 9
L/2 L/10
W/10
W/2
3
4 6
8

Acer Acer –LCD-B223W
8
UXGA 1600*1200@60Hz 75.000 P 60.000 P 162.000
WXGA 1360*768@60Hz 47.712 P 60.015 P 85.5
1440*900(Red)@60Hz 55.469 P 59.901 N 88.75
WXGA+ 1440*900@75Hz 70.635 N 74.984 P 136.75
WSXGA+ 1680*1050@60Hz 65.290 N 59.954 N 146.250
IBM MODES
640*350@70Hz 31.469 P 70.087 N 25.175
EGA 720x400@70Hz 31.469 N 70.087 P 28.322
MAC MODES
VGA 640*480@66.7Hz 35.000 P66.667 P 30.240
SVGA 832*624@75Hz 49.725 N 74.550 N 57.283
XGA 1024*768@75Hz 60.241 N 74.927 N 80.000
1152*870@75Hz 68.681 N 75.062 N 100.00
Other MODES
XGA 1024*768@72Hz 57.669 N72.086 N78.434
SXGA 1280*1024@70Hz 74.882 P 69.853 P 127.000
Note: 1. Non-interlace signals only (An interlace signal cannot be display)
2. Please refer to F/W specification for more detail
3. Each frequency of Power Macintosh and Sun Ultra is a reference value
4.3 Timing requirements
The LCD monitor must be capable of displaying standard resolutions within the vertical frequency range of 56 ~ 76 Hz
and the horizontal scan range of 31.5 ~ 84 KHz with maximum pixel clock of 190MHz.
Vertical / Horizontal Sync polarity: positive or negative.
If input signal is out of range of horizontal 31.5~84 KHz or vertical 56-76Hz, or pixel clock large than 165MHz, message
“Input Not Supported” is shown on screen.
4.1DDC data
V223W Analog
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 00 FF FF FF FF FF FF 00 04 72 1B 00 00 00 00 00
1 00 00 01 03 08 2F 1E 78 EA DE 95 A3 54 4C 99 26
2 0F 50 54 BF EF 90 A9 40 71 4F 81 40 01 01 95 00
3 95 0F 90 40 01 01 21 39 90 30 62 1A 27 40 68 B0
4 36 00 DA 28 11 00 00 19 00 00 00 FD 00 38 4D 1F
5 54 11 00 0A 20 20 20 20 20 20 00 00 00 FF 00 30
6 30 30 30 30 30 30 30 30 30 30 30 0A 00 00 00 FC
7 00 56 32 32 33 57 0A 20 20 20 20 20 20 20 00 CS

Acer Acer –LCD-B223W
9
V223W DVI
0 1 2 3 4 5 6 7 8 9 A B C D E F
0 00 FF FF FF FF FF FF 00 04 72 1B 00 00 00 00 00
1 00 00 01 03 80 2F 1E 78 EA DE 95 A3 54 4C 99 26
2 0F 50 54 BF EF 90 A9 40 71 4F 81 40 01 01 95 00
3 95 0F 90 40 01 01 21 39 90 30 62 1A 27 40 68 B0
4 36 00 DA 28 11 00 00 19 00 00 00 FD 00 38 4D 1F
5 54 11 00 0A 20 20 20 20 20 20 00 00 00 FF 00 30
6 30 30 30 30 30 30 30 30 30 30 30 0A 00 00 00 FC
7 00 56 32 32 33 57 0A 20 20 20 20 20 20 20 00 CS
5. Function Specifications
All the tests to verify specifications in this section shall be performed under the following standard conditions
unless otherwise noted. The standard conditions are:
Temperature : 25 ± 5°C
Warm-up time : 30 minutes minimum
Checking display modes : All the specified modes
5.1Panel general specifications
A General specifications
Supplier InnoLux
Model name INL MT190AW01(V-5)
Display Area 410.4 ( H ) x256.5 ( V )
Pixel Pitch 0.285(H) x 0.285(V)
Display Colors: 16.7 Million (6-bit + HI-- FRC)
Number of Pixel 1440x900 pixels
Pixel Arrangement RGB vertical stripe
Brightness 300cd/m2(Typ.) 250cd/m2(Min.)
Contrast Ratio 700:1 Typical
Viewing Angle Hor:160°, Ver: 160°
(Typical, CR>10)
Display Mode Normally White
Frame rate 75Hz
Response Time Tr + Tf = 5ms Typical
Surface Treatment Anti-glare, Haze = 25%,
Hard coating (3H)
Lamp 4 CCFL
Outline Dimension 427.2(W)x277.4(H)x16(D) Typ
5.2Keypad Function
5.2.1 Control buttons on the front bezel
C
ONTROL KEY KEYS FUNCTION
[AUTO]
A. When OSD un-displays, press [AUTO] to perform auto-adjustment
B. When OSD displays, press [AUTO] to return to previous level menu
C. When “e Color OSD” OSD displays, press [AUTO] to exit the OSD

Acer Acer –LCD-B223W
10
[MENU]
A. When OSD isn’t shown on screen, press [MENU] to enter OSD interface. The OSD
interface uses “ACER e Color Management” and “User” to instead “Contrast” and
“Brightness” separately. When press “ACER e Color Management” to show “e Color
OSD”, and press “User” to show OSD interface before. The translations of “ACER e
Color Management” and “User” are always English.
B. When OSD displays, press [MENU] to perform function of menu icon that is highlight or
enter next level menu
[►], [◄]
A. When “MENU OSD” displays, press these keys to change the contents of an
adjustment item, or change an adjustment value
B. When “MENU OSD” un-displays, if it is with audio, press [►] to show “Audio” OSD and
increase the volume, press [◄] to show “Audio” OSD and decrease the volume; else
it has no use to press these keys.
[e Color ]
A. When OSD un-displays, press [e Color] to show “e Color OSD”, and press again the
OSD can not disappear, but the time of “e Color OSD” disappearing is reset 10 second
again.
B. When OSD disappear not including “e Color OSD”, press [e Color] to show “e Color
OSD” OSD, the OSD before disappears, but the parameters of it should be saved
[POWER] Power on or power off the monitor
5.3Hot Key Operation
HOT KEY OPERATION
F
UNCTION
A
UTO e Colo
r
◄
►
MENU POWE
R
FACTORY MODE ●●ON
Press [e Color ] & [MENU] at the
same time, and then press
[POWER] for DC power on. OSD
menu will be shown with “F” on the
left top. Select “F” for entering
factory mode.
5.4
OSD Structure
The On-Screen Display (OSD) shall be an easy to use icon based menu through keypad OSD buttons or remote control
unit. The unit shall leave the factory with all OSD controls set to their default values.
First Second Third Control Range Default Value
User mode 50
Text mode 50
Standard mode 50
Graphics mode 60
Contrast --- 0 ~ 100
Movie mode 56
User mode 77
Text mode 44
Standard mode 77
Graphics mode 97
Brightness
Brightness --- 0 ~ 100
Movie mode 77

Acer Acer –LCD-B223W
11
Focus --- 0 ~ 100 Depend on each timing
Image
Clock --- 0 ~ 100 50 ○1
Horizontal --- 0 ~ 100 50
Position
Vertical --- 0 ~ 100 Depend on each timing
Warm (6500K) --- ---
Cool (9300K) --- ---
Red 0 ~ 100 80
Green 0 ~ 100 80
Color
User
Blue 0 ~ 100 80
NO-EMEA EMEA
English English --- ---
Deutsch Deutsch --- ---
Español Español --- ---
简体中文 Hollands --- ---
繁體中文 Русский --- ---
Français Français --- ---
Italiano Italiano --- ---
Language
日本語 Suomalainen
--- ---
English
Hor. Position --- 0 ~ 100 50
Ver. Position --- 0 ~ 100 50
OSD
OSD Timeout --- 10~ 120 20
Analog --- --- ---
Digital --- --- ---
Input (Dual)
DDCCI ON/OFF ON
Input (Analg
only) DDCCI ON/OFF ON
Resolution --- --- ---
H. Freq --- --- ---
V. Freq --- --- ---
Info
S/N ET000….0000(22)
Reset --- --- --- ---
Exit --- --- --- ---
Notes; ○1 Clock default 50 is for Visa timing. Others depend on timing.

Acer Acer –LCD-B223W
12
6. SOP of firmware upgrade
6.1 Operational condition:
Equipment: PC, ISP card, signal cable and power cable.
ESD requirements: antistatic wrists, antistatic gloves (fingers), and connecting cable
Name of ISP program: RTDTool_4.6.exe
Manufacture of FW IC：RTD 2525L
6.2 Operational steps:
1. Connection: connect PC to PCBA with signal cable, and then keep AC and DC in open state.
2. Adjust ISP programming
Firstly, double click ISP_Tool_v3.7.5EXEI and open ISP program, then select “Device”, next select
manufacturer model of FW IC, which should be correspondent with that of PCBA FW IC. Double click
Figure One.
FW IC
Model
One port of ISP
program card
is connected to
PC print port.

Acer Acer –LCD-B223W
13
Secondly﹐download FW software: first select “READ”, and then load FW software in Rooter
(Fig.2).
Thirdly, select “Connect” and enter ISP MODE as in the following Figure 3.
Software
Checksum
FW software
rooter

Acer Acer –LCD-B223W
14
Fourthly, select “AUTO”, and keep its default value. Click “RUN” for beginning programming. There
will be prompting if programming is OK.
Note: if programming fails or success rate is not high, click “Config” and adjust its speed in “E2PROM
DEVICE SETTING”

Acer Acer –LCD-B223W
15
◆Flowin
g
chart
After connecting, AC ON,
DC ON
Open ISP program
Choose manufacturer
and model of FW IC
LOAD FW software
Click Connect and enter
ISP MODE
Click AUTO and RUN for
beginning programming
Turn off power if
p
ro
g
rammin
g
is O
K
OK
OK
OK
OK
OK
OK NG
Choose Config
and adjust
pro
g
rammin
g

Acer Acer –LCD-B223W
16
02. Flat Panel Specification

SPEC NO.
MT220WW 01 V.0
PAGE
3/23
ALL RIGHTS RESERVED ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED
TO ANY OTHER FORMS WITHOUT
PRIOR
WRITTEN
PERMISSION FROM INNOLUX DISPLAY CORPORATION.
Contents:
A. General Specification
B. Electrical Specifications
1. Pin assignment
2. Absolute maximum ratings
3. Electrical characteristics
a. Typical operating conditions
b. Display color vs. input data signals
c. Input signal timing
d. Display position
e. Backlight driving conditions
C. Optical specifications
D. Reliability test items
E. Safety
F. Display quality
G. Handling precaution
H. Label
I. Mechanical drawings
Appendix

SPEC NO.
MT220WW 01 V.0
PAGE
4/23
ALL RIGHTS RESERVED ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED
TO ANY OTHER FORMS WITHOUT
PRIOR
WRITTEN
PERMISSION FROM INNOLUX DISPLAY CORPORATION.
A. General Specification
NO. Item Specification Remark
1 Display resolution (pixel) 1680(H) X 1050(V), WSXGA+ resolution
2 Active area (mm) 473.76(H) X 296.1(V)
3 Screen size (inch) 22 inches diagonal
4 Pixel pitch (mm) 0.282(H) X 0.282(V)
5 Color configuration R, G, B vertical stripe
6 Overall dimension (mm) 493.7 (W) X 320.1 (H) X 16.5 (D) (typ.)
7 Weight (g) 2900 (max.)
8 Surface treatment Anti-glare, Haze = 25%, Hard coating (3H)
9 Input color signal 8 bit LVDS
10 Display colors 16.7 M (6 bit with Hi-FRC)
11 Optimum viewing direction 6 o’clock
12 Backlight 4 CCFL
13 RoHS RoHS compliance

SPEC NO.
MT220WW 01 V.0
PAGE
5/23
ALL RIGHTS RESERVED ANY PORTION OF THIS DOCUMENT SHALL NOT BE REPRODUCED, COPIED, OR TRANSFORMED
TO ANY OTHER FORMS WITHOUT
PRIOR
WRITTEN
PERMISSION FROM INNOLUX DISPLAY CORPORATION.
B. Electrical Specifications
1.Pin assignment
Connector 
JAE FI-XB30SSRL-HF16, Foxconn GS23302-0311R-7F or mechanical interface equivalent connector.
Pin No.
Symbol Description
Frame
VSS Ground
1 RXinO0- -LVDS differential data input, Chan 0-Odd
2 RXinO0+ +LVDS differential data input, Chan 0-Odd
3 RXinO1- -LVDS differential data input, Chan 1-Odd
4 RXinO1+ +LVDS differential data input, Chan 1-Odd
5 RXinO2- -LVDS differential data input, Chan 2-Odd
6 RXinO2+ +LVDS differential data input, Chan 2-Odd
7 VSS Ground
8 RXOC- -LVDS differential Clock input (Odd)
9 RXOC+ +LVDS differential Clock input (Odd)
10 RXinO3- -LVDS differential data input, Chan 3-Odd
11 RXinO3+ +LVDS differential data input, Chan 3-Odd
12 RXinE0- -LVDS differential data input, Chan 0-Even
13 RXinE0+ +LVDS differential data input, Chan 0-Even
14 VSS Ground
15 RXinE1- -LVDS differential data input, Chan 1-Even
16 RXinE1+ +LVDS differential data input, Chan 1-Even
17 VSS Ground
18 RXinE2- -LVDS differential data input, Chan 2-Even
19 RXinE2+ +LVDS differential data input, Chan 2-Even
20 RXEC- -LVDS differential Clock input (Even)
21 RXEC+ +LVDS differential Clock input (Even)
22 RXinE3- -LVDS differential data input, Chan 3-Even
23 RXinE3+ +LVDS differential data input, Chan 3-Even
24 VSS Ground
25 VSS Ground
26 NC No Connection
27 VSS Ground
28 VCC +5.0V power supply
29 VCC +5.0V power supply
30 VCC +5.0V power supply
Frame VSS Ground