Acer P243W User manual

Table of Contents
Important Safety Notice------------------------------------------------------------------------------------- 01
01. Product Specification--------------------------------------------------------------------------------- 02
02. OSD Menu-----------------------------------------------------------------------------------------------08
03. Exploded Diagram
05.
AppendixI:User’s Manual
------------------------------------------------------------------------------------- 10
Troubleshooting----------------------------------------------------------------------------------------20
06. Schematics and Layouts------------------------------------------------------------------------------ 31
04. Assembly and Disassembly Procedures-----------------------------------------------------------12
Appendix II : Spare Parts Llist
Safety Notice
Any person attempting to service this chassis must familarize with the chassis and be aware of the
necessary safety precautions to be used when serving electronic equipment
containing high voltage.
Published by LITE-ON Service Printed in Taiwan © All rights reserved Subject to modification
21th-Nov-2007
Model ID:MB243WABNS
Service
ACER
ACER_LCD_P243W_SM071121V3
Service Manual

Product Anouncement:
This product is certificated to meet RoHS Directive and
Lead-Free produced definition. Using approved critical
components only is recommended when the situation
to replace defective parts. Vender assumes no liability
express or implied, arising out of any unauthorized
modification of design or replacing non-RoHS parts.
Service providers assume all liability.
Qualified Repairability:
Proper service and repair is important to the safe,
reliable operation of all series products. The service
providers recommended by vender should being
aware of notices listed in this service manual in order
to minimize the risk of personal injury when perform
service procedures. Furtermore, the possibile existed
improper repairing method may damage equipment or
products. It is recommended that service engineers
should have repairing knowledge, experience, as well
as appropriate product training per new model before
performing the service procedures.
NOTICE:
To avoid electrical shocks, the products should be
connect to an authorized power cord, and turn off the
master power switch each time before removing the
AC power cord.
To prevent the product away from water or explosed
in extremely high humility environment.
To ensure the continued reliability of this product,
use only original manufacturer’s specified parts.
To ensure following safty repairing behavior, put the
replaced part on the components side of PWBA, not
solder side.
!
!
!
!
To ensure using a proper screwdriver, follow the
torque and force listed in assembly and disassembly
procedures to screw and unscrew screws.
!
Using Lead-Free solder to well mounted the parts.!
!The fusion point of Lead-Free solder requested in the
degree of 220 C.°
Important Safety Notice
Go to cover page
1
ACER P243W

1.1 SCOPE
This document defines the design and performance
requirements for a 24W inch diagonal , flat panel monitor
.The display element shall be a WUXGA (1920x1200)
resolution TFT-LCD (Thin Film Transistor Liquid Crystal
Display).16.7M color(RGB Hi+FRC) images are displayed
on the panel.Video input signals are analog RGB (0.7Vp-p).
When the systemis powered-on , previously stored screen
parameters for a pre-defined mode will be recalled if the
operating mode is one of stored in memory( 24 factory , 9
users timing ).This monitor operates normal by non-
interlaced mode. DDC (Display Data Channel) function is
DDC2Bi compliance Power saving function complies with
the DPMS (Display Power Management Signaling)
standard.
1.2 GENERAL REQUIREMENTS
AMLCD: LTM240CT01
LTM240CT03
1.2.1 Test Condition
Brightness level & contrast level max. Full white
pattern test mode following spec. Warm up more than
1 hr, ambient light < 10 Lux , Luminance meter
CA110 or BM7 or same equipment .
1.2.2 Test Equipment
The reference signal source is a calibrated Chroma
2135 video generator or higher.The use of other
signal generators during qualification and production
is acceptable provided the product complies with this
specification.
1.3 ELECTRICAL
This section describes the electrical requirement of the
monitor. The LCD monitor consists of an interface board , a
power board , a function key board. The interface board
wil l house the flat panel control logic , brightness
control logic, audio function control (option), key function
control, DDC and DC to DC conversion to supply the
appropriate power to the whole board and LCD flat panel ,
and transmitting LVDS signals into LCD flat panel module
to drive the LCD display circuit .The power board will
support main power DC5V to interface board, and the
power DC5.3V to audio function power of interface board,
and drive the two CCFLs (Cold Cathode Fluorescent
Tube).The interface board provides the power ON / OFF
control over the whole monitor and control for DPMS LED
indicator to function key board.
1.3.1 Interface Connectors
1.3.1.1 Power Connector and Cables
The AC input shall have an IEC/CEE-22 type male
power receptacle for connection to mains power.
The power cord shall be with length of 1.8+/-0.005
meters.
1.3.1.2 Video Signal Connectors and Cable
The signal cable shall be 1.8 0.005 meters long.
At the end of the cable shall be a molded-over,
shielded,triple row, 15 position, D-subminiature
connector. The CPU connection shall have captive
screw locks, which will be adequate for hand
tightening. The monitor connection may use small
screws.
+/-
1. Product Specification
2
Go to cover page
ACER P243W
SPEC
Signal Input Frequency Analog :
H : 30kHz~94kHz
(Analog) V : 55Hz~76Hz
Pixel clock 205MHz (Max)
Video Input Analog 0.7Vp-p
Display Pixels 640 x 480 (VGA) ~ 1920 x 1200 (WUXGA)
Sync Signal Separate SYNC for TTL (N or P)
Signal Input Frequency Digital :
H : 30kHz~94kHz
(Digital) V : 55Hz~76Hz
Pixel clock 165MHz (Max)
Video Input Analog 0.7Vp-p
Input Impedance 75Ω
Display Pixels 640 x 480 (VGA) ~ 1920 x 1200 (WUXGA)
Connector AC Input AC100V ~ AC240V ± 10% 50/60Hz , 3 pin AC power cord
Input connector D-SUB 15 pin & DVI-D
Audio Jack (OPTIONAL) Audio input 3.6F
Power Consumption AC in 100V~240V active 90W, power saving < 2W
User's Control Front Empowering,Auto Adjust,Adjust(-),Adjust (+),Menu,Power
OSD Contrast , Brightness , Position ,Clock ,Phase
,Analog/Digital,RESET, Color , Language select , etc.
Pre-Defined Timing Factory 24
User 9
Plug and Play VESA DDC2Bi
Power Saving VESA DPMS
Input Signal Counter Tolerance ≦H±1kHz, ≦V±1Hz
MONITOR SPECIFICATIONS
ITEM

1. Product Specification (continued)
1.3.2 Video Input Signals
1.3.2.1 Video Signal Amplitudes
The three video inputs consist of Red ,Green , and Blue
signals, each with its own coaxial cable terminated at the
monitor. These video signals are analog levels, where 0
V corresponds to black , and 700 mV is the maximum
signal amplitude for the respective color, when each
signal is terminated by a nominal 75.0 ohms .For a given
monitor luminance levels are measured using this
defined video amplitud driving a monitor meeting the
termination requirements .The signal amplitude is not to
be readjusted to compensate for variations in termination
impedance.
1.3.2.2 Video Signal Termination Impedance
This analog video signal termination shall be 75 1%
which shall be resistive with a negligible reactive
component
1.3.2.3 Synchronization ( Sync ) Signals
The Horizontal Sync (HS) TTL signal is used to initiate
the display of a horizontal line. HS may be either active
high or active low, depending upon the timing .The
Vertical Sync (VS) TTL signal is used to initiate the
display of a new frame .VS may be either active high or
active low, depending on the timing
1.3.2.4 Sync Signal Levels
The monitor must accept sync signals from both 3.3 and
5 volt TTL logic families.The inputs shall sense a logic 0
when the input is 0.8 volt or less and shall sense a logic
1 when the input is 2.0 volts or greater. In addition to
these level requirements, there shall also be a minimum
of 0.3 volt hysteresis provided for noise immunity
(typically by using a Schmitt Trigger input ).That is , the
input level at which the monitor actually detects a logic 0
shall be at least 0.3 volt lower than the level at which it
actually detects a logic 1.If the monitor sync processing
circuits are designed around the 3.3 volt logic family
,then the sync inputs must be 5 volt tolerant .
TTL input loading shall be equivalent to one TTL input
load. When logic 0 is asserted by a sync input , the
maximum current source from any single monitor sync
input to the driver is 1.6 mA .When logic 1 is asserted ,
the maximum current source from the driver to any
single monitor sync input is 400 uA .
Ω+/-
.
1.3.2.5 Sync Signal Loading
DSUB
P in S ig n a l P in S ig n a l P in S ig n a l
1R ed-V ideo 6Red-GND 11 NC
2G reen-V ideo 7Green-GND 12 DDC-SDA
3Blue-Video 8Blue-GND 13 H-SYNC
4NC 9+5V 14 V-SYNC
5DDC-GND 10 Sync-G N D 15 DDC-SCL
Connector Pin Assignm ent
D-SUB Pin Description
Pin N ame D e scription
1 Red-Video Red video signal input.
2 Green-Video Green video signal input.
3 B lu e - V id e o B lu e vid e o s ig na l in p u t.
4GND Ground
5 DDC-GN D DDC ground for the VESA DDC 2Bi function.
6 Red- GN D Analog signal gro und for the Red video .
7 Green-GN D Analog signal ground for the Green video.
8 B lue-G N D Analog signal ground for the Blue vid eo.
9 +5V +5V input from host system for the VES A DDC 2Bi function.
10 Sync-GND Signal ground
11 GN D Ground
12 DDC_SDA SDA signal input for the VESA DDC B2i function.
13 H -S YN C Horizontal signal input from the host system.
14 V -S YN C Vertical signal input from the host system.
15 DDC-SCL SC L signal input for the VESA DDC 2Bi function.
Connector Pin Description
DVI-I / DVI-D (If using DVI-D cable, C1, C2, C3, C4, C5 is NC)
Pin Signal Pin Signal Pin Signal
1RX2- 11 GND 21 NC
2RX2+ 12 NC 22 GND
3GND 13 NC 23 RXC+
4NC 14 5V 24 RXC-
5NC 15 GND C1 Analog Red (NC)
6SCL 16 HP C2 Analog Green (NC)
7SCA 17 RX0- C3 Analog Blue (NC)
8Analog V-Sync (NC) 18 RX0+ C4 Analog H-Sync (NC)
9RX1- 19 GND C5 GND
10 RX1+ 20 NC
DVI-I / DVI-D Connector Pin Description
Pin Name Description Pin Name Description
1 RX2- TMDS link #0 channel #2 differential pair 16 HP Hot plugging
2 RX2+ TMDS link #0 channel #2 differential pair 17 RX0- TMDS link #0 channel #0 differential pair
3 GND GND for no link share 18 RX0+ TMDS link #0 channel #0 differential pair
4 NC NC 19 GND GND for no link share
5NC NC 20NC NC
6 SCL Clock line for DDC interface 21 NC NC
7 SDA Data line for DDC interface 22 GND Clock shield
8Analog
V- Sync V- sync for analog interface 23 RXC+ TMDS clock differential pair
9 RX1- TMDS link #0 channel #1 differential pair 24 RXC- TMDS clock differential pair
10 RX1+ TMDS link #0 channel #1 differential pair C1 Analog
Red Analog Red signal
11 GND GND for no link share C2 Analog
Green Analog Gr een signal
12 NC NC C3 Analog
Blue Analog Blue signal
13 NC NC C4 Analog
H- Sync H- sync for analog interface
14 5V +5V input fromhost system for DDC2B function. C5 Analog
GND Analog GND
15 GND Ground(Using as Detect Cable)
No. Sym bol Item M in Norm al Max Unit Remark
1Fh Scanning H orizontal Frequency 30 94 kH z M inim um range
2Fv Scanning V ertical F requency 55 76 H z M inim um range
3V ih H i L evel Input 2 5 N ote 1)
4V il L ow L evel Input 0 0.8 V N ote 1)
5V ideo R G B A nalog V ideo L evel 0.0 0.7 1.0 V 75Ωto G round
N o te 1 ) S c h m itt- T r ig g e rs In p u t , S upported 3.3V device H (& V ) sync output from PC .
V ideo Input Signal
Go to cover page
3
ACER P243W

1.3.2.6 Abnormal Signal Immunity
The monitor shall not be damaged by improper sync
timing , pulse duration , or absence of sync , or
abnormal input signal amplitude ( video and/ or sync
too large or too small) , or any other anomalous
behavior of a graphics card video generator when
changing modes , or when any combination of input
signals is removed or replaced . Additionally , under
these conditions , the monitor shall not cause
damage to the driving source
1.3.3 User Controls and Indicators
1.3.3.1Power On / Off Switch
The monitor shall have a power control switch
visible and accessible on the front of the monitor .
The switch shall be marked with icons per IEC 417 ,
# 5007 and # 5009.The switch shall interrupt the DC
supply to the monitor
1.3.3.2 Power Indicator LED
The monitor shall make use of an LED type
indicator located on the front of the monitor .
The LED color shall indicate the power states as
given in Table 1.
1.3.4 Monitor Modes and Timing Capability
1.3.4.1 Format and Timing
The monitor shall synchronize with any vertical
frequency from 55 to 76 Hz , and with any
horizontal frequency from 30 to 94KHz. If the input
frequency is out of the above – specified range,
the monitor shall display a warning screen
indicating that the input frequency is out of range.
Under no circumstances shall any combination of
input signals cause any damage to the monitor .
1.3.4.2 Factory Assigned Display Modes
There are 24 factory pre-set frequency video
modes. These modes have a factory pre-set for all
characteristics affecting front-of-screen
performance. When the system is powered-
on,previously stored screen parameters for a pre-
defined mode will be recalled if the operating
mode is one of those stored in memory. If the
operating mode is not one of those stored in
memory, the monitor CPU will select the PRESET
timing for a mode that is the next lowest in
horizontal scanning frequency to the mode being
currently used. The screen parameters may be
adjusted by the use of the front bezel controls and
then may be saved as a user defined mode. The
monitor shall include all the preset video timings
shown in the following page.(Please see Note.(3) )
1.3.3.4 OSD adjustment
1. Product Specification (continued)
Function LED Color
Full Power Blue color
Sleep Orange color
Table 1
1.3.3.3 On-Screen Display
The Lite-ON On Screen Display system shall be
used , controlled by a Menu button. If the buttons
remain untouched for OSD turn off time while
displaying a menu , the firmware shall save the
current adjustments and exit. Also, if the video
controller changes video mode while the OSD is
active, the current settings shall be saved
immediately, the OSD turn off, and new video mode
is displayed.
Key When no OSD display OSD Displayed
1. To display the OSD menu on the screen.
2. To select the OSD sub-Menu
>Speaker Volume/Plus
(with Audio)
1. Back-forward selection of the OSD menu.
2. Decrease the value after sub-menu selected.
<Speaker Volume/Minus
(with Audio)
1. Forward selection of the OSD menu.
2. Increase the value after sub-menu selected.
E Empowering Menu or sub.menu EXIT/Scenario mode
Menu or sub.menu auto adjust
Auto Auto Adjust Function
Description
MENU Menu Display
ITEM CONTENT
BRIGHTNESS Back light Luminance of the LCD panel is adjusted.
CONTRAST A gain of R , G and B signal is adjusted.
AUTO CONTRAST A gain of R , G and B signal auto adjust.
CLOCK The ratio of dividing frequency of the dot clock is adjusted.
PHASE The phase of the dot clock is adjusted.
H-POSITION The indication screen is horizontally moved right and left (1 Pixels pitch).
V-POSITION The indication screen is vertically moved up and down (1 Pixels pitch).
AUTO ADJUST Clock system auto adjustment, about under 8 sec.
COLOR BALANCE Select three kinds of modes. ( USER /WARM / Cold ).
OSD POSITION The OSD indication position can be adjusted.
OSD LANGUAGE Select the language used for the OSD menu among English , French ,
Italian , Deutsch and Spanish.
RECALL DEFAULTS All data copy from factory shipment data.
OSD DURATION Adjust OSD menu off time range from10~120 second.
POWER-SAVE Back light of the LCD panel is cut when the signal is not input (AC line
power consumption 2W or less).
INFORMATION The frequency of the horizontal / vertical synchronizing signal under the
input is indicated.
※NOTE : OSD MENU SEE APPENDIX A
4
Go to cover page
ACER P243W

1.3.5 Controller Requirements
1.3.5.1 General Requirements
The monitor shall include a controller capable of
converting the analog RGB signal from a standard
WUXGA resolution video controller in the CPU to a
signal which can be displayed on the panel. The
controller will include a PLL, A/D converters, LVDS
transmitter and other circuitry necessary to perform
its function. The PLL shall be stable enough to
ensure that a static image from the CPU is placed
in the same physical location on the flat panel in
each frame.
1.3.4.3 Mode Recognition Pull-in
The monitor shall recognize preset modes within a
range of +/-1KHz whichever is less for horizontal ;
and within +/-1Hz for vertical.
1.3.4.4 User Display Modes
In addition to the factory pre-set video modes,
provisions shall be made to store up to 9 user
modes. If the current mode is a user mode, the
monitor shall select its previously stored settings.
If the user alters a setting, the new setting will be
stored in the same user mode. The user modes
are not affected by the pre-set command. If the
input signal requires a new user mode, storage of
the new format is automatically performed during
user adjustment of the display (if required).(
Please see Note.(4) )
Preset timing Chart
1.3.5.2 Video Stretching
The monitor shall contain provisions to “stretch” the
video signal, so that an input signal from the
computer in any resolution smaller than 1920 x
1200 is automatically expanded to fill the entire
screen.
1.3.5.3 Panel Timing and Interface
The controller supplied with the monitor shall
control all panel timing. This controller shall
adequately insulate the monitor from the computer,
so that no possible combination of input signals
from the computer shall cause damage to the flat
panel or any other component of the monitor. The
LCD panel interface shall support the TFT
standard.
1.3.6 DC - AC Inverter Requirements
The DC-AC inverter is on the power board. The
frequencies used by the DC-AC inverter used to power the
backlight shall be chosen so as to prevent any noticeable
effects on the flat panel (such as a rolling effect).
1.3.7 Power Supply Requirements
The AC to DC converter power supply for the monitor shall
be an external AC to DC converter ”brick” This brick shall
have an IEC receptacle for main power input and a pin - in
---socket for DC power out. The brick shall provide
sufficient power for both the monitor and the backlight
assembly, and shall meet requirements specified in Table
2.
1. Product Specification (continued)
H-Sync V-Sync Band Width
(K Hz ) (H z) (M H z) H V
1 720 x 400 31.472 70.4 28.325 - + VGA
2 640 x 480 31.469 59.94 25.175 - - VGA
3 640 x 480 37.5 75 31.5 - - VESA
4 648 x 500 31.234 57.735 31.234 + + MAC
5 800 x 600 37.879 60.3 40 + + VESA
6 800 x 600 46.875 75 49.5 + + VESA
7 1024 x 768 48.363 60 65 - - VESA
8 1024 x 768 60.023 75 78.75 + + VESA
9 1280 x 1024 63.981 60 108 + + VESA
10 1280 x 1024 79.976 75 135 + + VESA
11 1440 x 900 55.469 59.01 88.75 + - CVT-RB
12 1440 x 900 55.935 59.887 106.5 - + CVT
13 1440 x 900 70.635 74.98 136.75 - + CVT
14 1280 x 720 45 60 74.25 + + CEA-861
15 1280 x 800 49.702 60 83.5 - + CVT
16 1280 x 800 62.795 75 106.5 - + CVT
17 1600 x 1200 75 60 162 + + VESA
18 1600 x 1200 74.006 59.924 130.25 + - CVT-RB
19 1600 x 1200 93.75 75 202.5 + +/- VESA
20 1680 x 1050 65.29 59.954 146.25 - + CVT
21 1680 x 1050 64.674 59.883 119 + - CVT-RB
22 1680 x 1050 82.306 74.892 187 - + CVT
23 1920 x 1200 74.038 59.95 154 + - CVT-RB
24 1920 x 1200 74.556 59.885 193.25 + - CVT
NOTE : (1) 76 ≦FV ≦86 : monitor can display but doesn't guarantee.
(2) fV < 55, or fV > 86 : warning invalid mode.
(3) Factory model :
After we first burn the code into the flash, every preset-model we run first must do auto-adjusting.
Then it'll not do auto-adjust again when we changed preset-mode back including AC on/off DC on/off.
The only way that preset-mode do auto-adjust again is press '' Internal Factory Reset''.
(4)Usermode:
The code should memorize 9 timing mode exclusive of preset-modes as use mode and do auto-adjusting.
When user set a new mode that is not among previously. It'll do auto-adjusting then be solved to user mod
e
The new mode will overwrite the first memorized user modes.
The user modes be cleared is same as Factory mode. Just do '' Internal Factory Reset''.
(5) Internal Factory Reset and O SD Factory Reset behavior.
Item Resolution Polarity Source
Preset Timing Chart
FACTORY PRESET VIDEO TIMINGS (DIGITAL INPUTS)
CEA-861-C
code
H-Active V-Active I/P H-tot. HB V-tot. VB
H-freq
(kHz)
V-freq
(Hz)
Pixel
freq
(MHz)
Inputs
17,18 720 576 P 864 144 625 49 31.250 50.000 27.000 DVI,HDMI
19 1280 720 P 1980 700 750 30 37.500 50.000 74.250 DVI,HDMI
20 1920 1080 I 2640 720 1125 22.5 28.125 50.000 74.250 DVI,HDMI
21, 22 1440 576 I 1728 288 625 24.5 15.625 50.000 27.000 HDMI
31 1920 1080 P 2640 720 1125 45 56.250 50.000 148.500 DVI,HDMI
39 1920 1080 I 2304 384 1250 85 31.250 50.000 72.000 DVI,HDMI
2, 3 720 480 P 858 138 525 45 31.469 59.940 27.000 DVI,HDMI
4 1280 720 P 1650 370 750 30 44.955 59.940 74.176 DVI,HDMI
5 1920 1080 I 2200 280 1125 22.5 33.716 59.940 74.176 DVI,HDMI
6, 7 1440 480 I 1716 276 525 22.5 15.734 59.940 27.000 HDMI
16 1920 1080 P 2200 280 1125 45 67.433 59.940 148.352 DVI,HDMI
■ Digital inputs (DVI, HDMI): Conflicting video- and PC
timings are to be treated as Video timings with one
exception: 640x480p/60Hz timing to be treated as PC-timing.
Analog input (VGA) treats all timings as PC-timings.
■
Go to cover page
5
ACER P243W

1.3.8 Display Communications Channel
The monitor assembly shall provide a display
communications channel that conforms to VESA
DDC2Bi hardware requirements. This configuration
shall contain the 128-byte EDID file as specified by
VESA EDID standard.The monitor should not write to
the EDID file for the first two minutes of operation
following power-up UNLESS some action taken by the
user or the host CPU forces the write (for instance,
requesting the serial number via the OSD).
Furthermore, it is recommended that CMOS switches
be incorporated to isolate the DDC IC from outside
connections while the EDID Fault Management is
being updated. This is to prevent corruption of the data
by attempts to read the data while it is being changed.
1.3.9 Firmware Update Function (same ISP function)
The update firmware need through from the D-Sub
connector, use DDC I2C bus to do update firmware.
1.4 PANEL ELECTRICAL
1.4.1 General Requirements
The panel used as the display device shall be an
WUXGA resolution, 24W TFT-LCD. This panel shall be
approved for use in this monitor.
1.4.2 Panel Timings
The controller included with the monitor shall translate all
video timings from the CPU that meet the timing
requirements listed in Panel specification into timings
appropriate for the panel. Under no circumstances may the
controller supply the panel with timings that may result in
damage. The controller shall insulate the panel from the
CPU , so that the panel shall always be driven per it's own
specification regardless of the timings being sent from the
CPU.
1.4.3 Polarizer Hardness
The outer face of the front polarizer panel shall be
covered with a coating witha#3hardness value
1.4.4 Backlight Requirements
1.4.4.1 General Requirements
The backlight assembly shall be designed to
support field replacement at the customer site or
authorized service center. The lamps shall have a
continuous operating life of at least 40,000 hours at
25. The operating life is defined as having ended
when the illumination of light has reached 50% of
the initial value. The lamps shall extend a sufficient
amount from the edge of the light guide that
sputtering over the life of the lamps shall not cause
degradation of the luminance uniformity (such as
non-illuminated bands along the edges of the
display).
.
1.4.4.2 Lamps Startup Time
The backlight lamps shall start about 2 sec of the
time the monitor power switch is pressed or the
monitor is restarted from a power - down mode
.The starting time shall stay about 2 sec. for the
minimum expected life of the lamps.
Test conditions are as follows :
Ambient Light ---------------------- < 1.0 lux
Temperature-------------------------- 10
Inactive Time ----------------------- > 24 hours
1.4.5 Defects
1.4.5.1 Visual Inspection
The LCD panel shall be inspected with all pixels
set to white,black , red , green , and blue. The color
variation, brightness variation , and overall
appearance must not be perceived as poor quality
by Lite-On . Areas and / or parameters considered
questionable shall be subjected to detailed
measurements .
℃
1. Product Specification (continued)
Input Voltage Range The operating range shall be from 90 to 132 and 195 to 265 AVC
sinusoidal for all models specified.
Input Frequency Range Input power frequency range sha;; be from 47.5 to 63 Hz over the
specified input voltage range.
Power Consumption
Power consumption for the monitor shall be less than 46W over the
specified voltage and frequency ranges. In suspend or sleep mode
the power consumption will be less than 2W.
Line Fuse The AC input shall be fused and become electrically open as a result
on an unsafe current level. The fuse many not be user replaceable.
Initial Cold Start
The power supply shall start and function properly when under full
load, with worst case conditions of input voltage, input frequenct,
operating temperature, and cold backlight lamps.
Inrush Current
The inrush current must be limited to 30A when operated at
120VAC, and 50A when operated at 220VAC. Inrush current is
measured at an ambient temperature of 25oC, with the unit
temperature stabilized in the power-off.
Hot Start Cycle
The power supply shall be damaged when switched ON for one
second and OFF for one second for seven consecutive after
operating for one hour at full load, 25oC, and nominal input line
voltage.
Under Voltage
The power supply shall contain protection circuitry such that the
application of an input voltage below the minimum specified in this
table shall not cause damage to the power supply unit nor cause
failure of the input.
Line Transient
The power supply shall operate within IEC 801-4 (± 1KV) and IEC
801-5 (± 2KV) for the domestic U.S. version. The UPS power
supply shall operate and comply with CE mark.
AC to DC Converter Requirements
Table 2
6
Go to cover page
ACER P243W

1.4.5.5 Defect Terminology
Table 3 gives the descriptive terms used in classifying
defects.
1.5 Optical Characteristics
Depends on the LCD supplier's spec. Details refer to QA
Inspection Spec.
1.4.5.6 Smudges, Streaks and Smears
When viewing the panel oriented so as to maximize
reflected light , there shall be no visible smudging ,
streaking, smearing or other nonuniformity from
contaminants ,fingerprints,or defects in any of the
visible surfaces. This is independent of whether the
unit is operating or off .
1.4.5.7 Other Defects
Undefined defects that are considered to be
rejectable by Lite–On will be reviewed by Lite-On as
they become apparent. These panels will be referred
to the Lite - On Corporate / Manufacturer Purchasing
Agreement for disposition.
1.4.5.8 LCD Inspection
Put LCD panel on inspection table and illuminate the
panel with a daylight fluorescent lamp located above
the panel surface such that the luminance at the
LCD panel is between 1000 lux and 1500 lux .Defect
limits are given in Table 4 .
1. Product Specification (continued)
1.4.5.2 Display Degradation
Over the life of the product , variation of the parameters
specified in Panel specification shall be maintained
within reasonable limits.The panel must not exhibit any
significant defects while in operation ( excluding the
CCFL operation ).This does not in any way change the
warranty given by the panel manufacturer .
1.4.5.3 Light Leakage
Except for the active display area , there shall be no
light emission visible from any angle from any other part
of the display . For this test , the ambient illumination
must follow panel's specification.
1.4.5.4 Allowable Defects
No cosmetic defects are allowed except those specified
below.The conditions of visual inspections are as follows
For 24W Series.
Viewing distance is to be approximately 35-50cm
Ambient illumination is to be 300 to 700 lux.
Viewing angle shall be at 90 degree.
Defects not apparent within one minute shall be
ignored.
■
■
■
■
Dark / Spots / Lines
Spots or lines that appear dark in the display patterns and are
u su a lly th e re su lt o f c o nta m in atio n . D e fe cts d o n o t v a ry in
siz e o r in ten s ity ( co n tra st) w h e n c o n tra st v o lta g e is v a rie d .
Contrast variation can be achieved through the use of varying
gray shade patterns.
Bright Spots / Lines
Spots or lines that appear light in the display patterns.
D e fe cts d o n o t v a ry in s ize o r in te n sity (c o n tra st) w h en
contrast voltage is varied. C ontrast variation can be achieved
through the use of varying gray shade patterns.
Polarizer Scratch
W h e n th e u n it lig h ts , lin e s a p p ea r lig h t (w h ite ) w ith d isp la y
p a tte rn s d a rk a n d d o n o t v a ry in s ize . P h y s ica l d a m ag e to th e
polarizer that does not dam age the glass
Polarizer D ent
W h e n th e u n it lig h ts , sp o ts a p p e ar lig h t (w h ite) w ith d isp la y
p a ttern s d ar k an d d o n o t v a ry in siz e . P h y sic a l d a m a g e to th e
polarizer that does not dam age the glass.
R u b b in g L in e
Horizontal or diagonal lines that appear gray w ith the display
patterns dark and m ay have resulted from an “out of control”
ru b b in g p ro c e ss o n th e p o ly im id e o r “ w a v e s” o n the B E F s o r
prism sheets.
N ew ton R ing Th e “rainbo w ” effect caused by non-uniform cell thickness.
M ottlin g
W h e n th e u n it lig h ts , v a riatio n / n o n – u n ifo rm ity
(s p lotc h in e ss ) a p p e ars lig h t (w h ite ) w ith th e d is p lay a n d
m ight vary in size.
Dim Line W h e n th e u n it lig h ts , lin e (s) in th e m o n ito r (v e rtic al) o r m ajo r
(h o riz o n tal) a x is a p p e ar d im , b u t n o t c o m p le tely o n o r o ff.
Cross Lines Off W h e n th e u n it lig h ts, lin e s in b o th th e m in o r a n d m a jo r a x is
do not appear.
Bright/DarkDot Asub–pixel(R,G,Bdot)stuckoff/on(electrical).
Average Diameter smaller of
(L+W)/2 or L/20+2W Acceptable Number Minimum Separation
< 0.1mm Non countable N / A
0.1 mm ~ 0.3 mm 10 15 mm
0.31 mm ~ 0.5 mm 10 15 mm
0.51 mm ~ 1.25 mm 5 15 mm
1.26 mm ~ 2.5 mm 3 25.4 mm
2.51 mm ~ 3.75 mm 3 25.4 mm
Greater than 3.75 mm NONE Not applicable
Note : Allowable distance between spots of two sizes is the minimum separation
number for the smaller spot. Therefore, if there are two spots, 1.30mm and 0.4mm
in diameter, they must be at least 15mm apart.
7
Go to cover page
ACER P243W

2.1 MAIN OSD MENU
Outline:
The description for control function:
2 OSD Menu
Go to cover page
8
ACER P243W

2. OSD Manu (continued)
9
Go to cover page
ACER P243W