Acme Furniture 39235 User manual

ACME
This product has been carefully crafted of: MDF, solid pine
wood and/or pine veneers. These materials derive from
plantations, a renewable and well managed forest, therefore,
not endangering the environment. The highest quality
standards have been implemented to assure a sturdy and
reliable product. Due to the natural variances in the
graining of wood, you may notice
subtle differences in the
shading and tone of the
color stain, warp, holes,
wood knots and also small
cracks. This is not a defect.
But rather a result of the
natural beauty of the wood itself.
Care and
maintenance:
Dust when needed using
a smooth, dry cloth.
Household furniture
polish can be used
occasionally to restore luster.
About the Wood and Finish

ASSEMBLY INSTRUCTIONS
#39235
ACME
+
1:30 h
1
2
3
4
5
6
7
8
9
10
11 12
Compare with the parts list to be sure that all parts are included.

Part List: 39235 - Twin Captains Bed
12 12
10
11 11
10
12
13
14
15
16
17
18
19
19
20
21
22
23
24
13 13
1
2
3
4
5
5
5
6
6
7
9
9
8
8
7
5
(x3)
Manufacturer Label

*Actual size of screws and bolts, for measurements checking.
Qty
06
NKnob
Qty
06
P
Stopper
¹⁄" x 3 ¹⁄" Bolt (¹⁄ x 80mm)
Qty
08
D
Ø17
1/4 x 80 Screw
7,0 x 70 Screw7,0 x 70 Screw7,0 x 70 Screw7,0 x 70 Screw7,0 x 70 Screw7,0 x 70 Screw
Qty
04
E
Ø17
7,0 x 70 Screw7,0 x 70 Screw7,0 x 70 Screw7,0 x 70 Screw
Ø17
7,0 x 70 Screw
Ø17 2 ³⁄" Bolt (7 x 70mm)
7,0 x 70 Screw
Qty
02
H
CH 2" Screw (4 x 50mm)
4,0 x 50 Screw
Nail 10x10
Qty
12
L
MQty
04
Caster Allen
wrench
Qty
01
O
Qty
40
A
1 ⁹⁄" Wooden Dowel (10 x 40mm)
10 x 40 Wood Dowel
BQty
32
1" Wooden Dowel (8 x 25mm)
8 x 25 Wood dowel
Qty
12
C
Ø17 3 ¹⁵⁄" Bolt (7 x 100mm)
7,0 x 100 Screw
Qty
04
F
Ø17 2" Bolt (7 x 50mm)
7,0 x 50 Screw
GQty
08
¹⁄"
Elliptical
Nut
Qty
122
1 ³⁄" Screw (4 x 30mm)
4,0 x 30 Screw
CH
I
⁵⁄" Screw (3.5 x 16mm)
3,5 x 16 Screw
CH
Qty
22
K
Wooden
spacer
8 ⁹⁄" (217mm)
Qty
02
Q
³⁄" Screw (3.5 x 20mm)
Qty
12
J

(x4)
(x2)
INSIDE
5
6
6
1
2
3
4
6
5
5
5
5
01
02
A
A
A
C+O
C+O
C+O
C+O
O+C
O+C
O+C
O+C
O+C
O+C
C+O
C+O
A
A
A
A
A
A
A
A
A
A
Qty
32
A
1 ⁹⁄" Wooden Dowel
10 x 40 Wood dowel
Qty
12
C
Ø17 3 ¹⁵⁄" Bolt
7,0 x 100 Bolt
Allen
wrench
Qty
01
O
O
C
INSIDE
INSIDE
HEADBOARD / FOOTBOARD
INSIDE
Insert wooden dowels (A) into the holes, as shown in the diagram.
Attach crossbars 5 and bottom panel 6 at the legs 1,2,3 and 4 with bolts (C) using the allen wrench (O),
as shown in the diagram.

PRE-DRILLED HOLES
(x2)
7
7
8
8
9
03
04
1 ³⁄" Screw
4,0 x 30 Screw
CH
Qty
04
I
I
I
I
I
Qty
08
A
1 ⁹⁄" Wooden Dowel
10 x 40 Wood dowel
A
A
A
A
A
A
A
(x2)
7
I
I
2
3
1
4
BED RAILS / GUARDRAILS
Fix the stopper 7 to legs 2 and 3 with screws (I),
as shown in the diagram.
Insert wooden dowels (A) into the holes, as shown in the diagram.

INSERT AND
ATTACH BOLTS AND NUTS (D&G),
BUT DO NOT TIGHTEN UNTIL
STEP #07
INSERT AND
ATTACH BOLTS AND NUTS (D&G),
BUT DO NOT TIGHTEN UNTIL
STEP #07
8
8
05
06
Qty
04
D
Ø17
¹⁄" x 3 ¹⁄" Bolt
1/4 x 80 Bolt
Qty
04
D
Ø17
¹⁄" x 3 ¹⁄" Bolt
1/4 x 80 Bolt
GQty
04
¹⁄
Elliptical
Nut
GQty
04
¹⁄
Elliptical
Nut
Allen
wrench
Qty
01
O
Allen
wrench
Qty
01
O
O
D
O
D
D+O
D+O
D+O
D+O
O+D
O+D
G
G
G
G
G
G
G
G
O+D
O+D
2
3
4
1
1
4
G
G
Before inserting the bolts(D),
attach the elliptical nut(G)
as shown in the diagram.
Before inserting the bolts(D),
attach the elliptical nut(G)
as shown in the diagram.
First, x one of the headboard/footboard to the rail 8 and then the other headboard,
with bolts (D) and elliptical nuts (G), using the allen wrench (O).
Do not tighten the bolts until step # 07, in order to attach the other rail and guardrails.
Attach the other rail with bolts (D) and elliptical nuts (G), using the Allen wrench (O).
Do not tighten the bolts in order to attach the guardrails in step # 7.

AFTER ATTACHED
BOLTS ’’E’’
AT THIS TIME,
PLEASE TIGHTEN
ALL BOLTS!
9
9
10
07
08
O
E
E+O
E+O
O+E
O+E
Qty
04
E
Ø17 2 ³⁄" Bolt
7,0 x 70 Bolt
Allen
wrench
Qty
01
O
IIIIIIIIIIIII
IIIIIIIIIIIII
1 ³⁄" Screw
4,0 x 30 Screw
PN Qty
26
I
SLATS
0mm=
10
Align first slat with rail support.
Attach guardrails 9 to the headboard/footboard with bolts (E) using the allen wrench (O),
as shown in the diagram.
At this time, tighten all bolts.
Attach the rst slat aligned with the rail support with the screws (I).
Stretch the set and secure all slats.

(x3)
(x3)
11
11
12
09
10
11
I
I
I
I
I
I
B
B
B
B
B
B
1" Wooden Dowel
Qty
18
B
8 x 30 Wood dowel
I
I
Attention
Beveled edge
is front side
B
I
I
13
12
FRONT
BACK
FRONT
BACK
TRUNDLE COMPONENTS
1 ³⁄" Screw
4,0 x 30 Screw
PN Qty
06
I
1 ³⁄" Screw
4,0 x 30 Screw
PN Qty
06
I
9
9
Attach the supports 11 to the guardrails 9 using the screws (I).
Insert wooden dowels (B) into the holes, as shown in the diagram.
SPECIAL ATTENTION AFTER THIS STEP because it has back and front sides.
Please check the measurements between the holes to
idenfy front and back sides.
Attach part 13 on support 12 with screws (I), aligning the beveled edge forward.
In support 12 the front side is the shortest measure up to the wooden dowel.
3 ⁹⁄"
3 ⁹⁄"
4 ⁵⁄"
4 ⁵⁄"

14
14
12
12
12
12
13
1" Wooden Dowel
Qty
04
B
8 x 30 Wood dowel
B
B
B
B
B
B
I
I
I
Beveled edge
is front side
I
1 ³⁄" Screw
4,0 x 30 Screw
PN Qty
03
I
Insert wooden dowels (B) into the holes, as shown in the diagram.
Attach support 12 to the part 14 with screws (I),
as shown in the diagram.
THIS STEP IS VERY IMPORTANT,
the part 12 have a chamfer on end that
need to be assembled to the front .

2"
2"
2"
2"
2"
15
16
15
16
14
15
Caster
Qty
04
M
M
M
M
M
M
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
K
B
B
B
B
B
K
1" Wooden Dowel
Qty
04
B
8 x 30 Wood dowel
Qty
02
H2" Screw
4,0 x 50 Screw
H
H
H
⁵⁄" Screw
PN Qty
16
K
FRONT
Insert wooden dowels (B) into the holes.
Attach the casters (M), about 2" away from edge,
to the sides 15 and 16 using the screws (K),
as shown in the diagram.
Attach the sides 15 and 16 to the part 14 with screws (H),
as shown in the diagram.
14
BEVELED EDGE

17
18
16
17
I
I
I
I
I
I
I
I
I
O
F
Qty
04
F
Ø17 2" Bolt
7,0 x 50 Bolt
Allen
wrench
Qty
01
O
O+F
O+F
O+F
O+F
I
I
1 ³⁄" Screw
4,0 x 30 Screw
PN Qty
09
I
Attach the front of the trundle 17 to the sides 15, 16 and supports 12 using the screws (I).
Attach the back panel 18 of the trundle to the sides 15 and 16 whith bolts (F)
using the allen wrench (O).
15
16
15
16
12
12
12

10
17
18
19
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Qty
03
NKnob
N
N
N
1 ³⁄" Screw
4,0 x 30 Screw
PN Qty
26
I
1 ³⁄" Screw
4,0 x 30 Screw
PN Qty
03
I
SLATS
KNOBS
0mm=
10
Align first slat with rail support.
Attach the rst slat aligned with the rail support with the screws (I).
Stretch the set and secure all slats.
Insert the knobs (N) into the holes and attach with the screws (I), as shown in the diagram.

19
19
20
20
21
Beveled
edge
Beveled
edge
BACK PART
BACK PART
FRONT PART
SIDE PART SIDE PART
Beveled
edge
19
19
20
21
Drawers
BACK PART
FRONT PART
BOTTOM PART
DRAWER FRONT
SIDE PART
SIDE PART
22
24
4 ¹⁄"
4 ¹⁄"
4.¹³⁄"
4.¹³⁄"
(x3) (x3)
20
21 22
I
I
I
I
GROOVES
ALIGNMENT
GROOVES
ALIGNMENT
1 ³⁄" Screw
4,0 x 30 Screw
PN Qty
06
I
1 ³⁄" Screw
4,0 x 30 Screw
PN Qty
06
I
(x3)
Attach the back part 20 to the side part 19
using the screws (I).
Align the base of the back part
with the groove of the side part
according to the detail.
Attach the front part 21 to the side part 19
using the screws (I).
Align the base of the front part
with the groove of the side part
according to the detail.
Pre-drilled holes
Pre-drilled holes

Beveled
edge
19
19
22
23
19
19
19 19
20
20
21
21
24
24
21
21
21
(x3)
(x3)
(x3)
(x3)
(x3)
(x3)
SIDE PART
SIDE PART
FRONT PART
BACK PART
FRONT PART
BOTTOM PART
FRONT PART
FRONT PART
SIDE PART
SIDE PART SIDE PART
FRONT PART
DRAWER FRONT
DRAWER FRONT
23 24
25
27
26
28
LQty
12
10x10
I
I
I
I
L
L
L
L
Qty
06
PStopper
P
P
P
K
K
B
B
K
1" Wooden Dowel
Qty
06
B
8 x 30 Wood dowel
II
II
J
J
Q
Q
J
J
Wooden
spacer
8 ⁹⁄"
Qty
02
Q
4"
4"
4"
1 ³⁄" Screw
4,0 x 30 Screw
PN Qty
12
I
4,0 x 20 Screw
³⁄" Screw
Qty
12
JCH ⁵⁄" Screw
PN Qty
06
K
1 ³⁄" Screw
4,0 x 30 Screw
PN Qty
12
I
Attach the side part 19 to the front part 21
and back part 20 using the screws (I).
Align the base of the back and front parts
with the groove of the side part
according to the detail.
Insert the bottom part 22 using the
grooves on the sides parts 19,
aligning with the front part 21 and
the back part 20, using the nails (L) to x.
Using the wooden spacers (Q),
position part 23 on the bottom
of the drawer and x with the screws (J).
With the help of a tape measure,
mark 4" from the back part
center at the height.
Attach the stopper (P) using the screws (K).
Insert wooden dowels (B)
into the holes, as shown in the diagram.
Attach the drawer front 24 at the front part 21
with the screws (I),

24
(x3)
29
30
Qty
03
NKnob
N
I
1 ³⁄" Screw
4,0 x 30 Screw
PN Qty
03
I
Insert the knobs (N) into the holes and attach with the screws (I), as shown in the diagram.
Attach one drawer at a time, tting the slide to the center rail.

31