Acme Furniture FBKHFK-108A User manual

Component List
Headboard & Footboard
A 1Headboard Panel
B
C
D
F
G
H
I
J
K
L
M
N
P
Q
Footboard Panel
Headboard Back Cover
Footboard Back Cover
1
1
1
No QtyDescriptions
Headboard Leg Left and Right
Footboard Leg Left and Right
Bed Rail
Drawer Slat
Drawer Slat Support
Drawer Slat Support Stopper
Bed Slat 3 Holes
Bed Slat Support
Center Slat With 3 Holes
Drawer
Slat Cover
2
2
2
1
1
1
3
3
1
1
Side Rail
Drawer
No QtyDescriptions
Leg
No QtyDescriptions
No QtyDescriptions
Page 1 of 6
ASSEMBLY INSTRUCTIONS
Bed Slat 2 Holes 10
ASSEMBLY TIPS :
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast and
easy assembly.
E
2
H
G
I
N
A
P
B
F
J
KL
M
Q
MODEL : FBKHFK-108A+FBKSRR-108A
+FBKDWR-108A
REVISION : A
Hardware List In Headboard & Footboard
No QtyDescriptions
1
2
3
4
5
6 9
30
12
3
12
1
CSK M4 x 32mm
JCBC Screw M6 x 35mm
JCBC Screw M6 x 50mm
Spring Washer Ø1/4"
Flat Washer Ø1/4" x 20mm
L Key M4 x 100mm
8Wood Dowel 10mm x 30mm
28
1L Key M5
L Key M4 x 65mm
10
1
Hardware List In Side Rail
No QtyDescriptions
7 16JCBC Screw M6 x 16mm
8 116CSK M4 x 16mm

STEP 1.1: Insert wood dowel (6) to the pre-drilled hole of headboard panel (A) / footboard panel (B).
STEP 1.2: Push the headboard leg (N) / footboard leg (P) to fit with the wood dowel (6) at the headboard panel (A) / footboard panel (B).
STEP 1.3: Attach the headboard leg (N) / footboard leg (P) by using JCBC Screw M6 x 35mm (1), springwasher (2) and flat washer (3) through the
pre-drilled hole of headboard leg (N) / footboard leg (P) and tighten by using Allen key (4).
STEP 1.4: Repeat Step 1.1 to step 1.3 For the other side leg.
STEP 1.5: Attach the headboard back cover (C) on the back side of headboard panel (A), and attach the footboard back cover (D) on the back side of
footboard panel (B).
Page 2 of 6
ASSEMBLY INSTRUCTIONS
CD
NP
A
B
"R" Marking behind
the Headboard & Leg
2
1
3
4
7
3
4
"L" Marking behind
the Headboard & Leg
"R" Marking behind
the Headboard & Leg
"L" Marking behind
the Headboard & Leg
6
A
B
STEP 1.5

STEP 2.1: Attach the bed rail (F) to headboard leg (N).
STEP 2.2: Tighten screw on headboard leg (N) by using L key M5 (5) & repeat the same step on footboard leg (P).
STEP 2.3: Attach the drawer slat (G) each to a drawer slat support (H) & fix with drawer slat support stopper (I).
STEP 2.4: Fix the drawer slat (G) to bed rail (F) with CSK M4 x 32mm (10).
STEP 2.5: Move 'T' runner at footboard panel (B) to drawer slat (G).
Page 3 of 6
ASSEMBLY INSTRUCTIONS
'T' Runner
STEP 2.5
G
B
I
G
STEP 2.4
10
STEP 2.1
F
STEP 2.2
F
5
STEP 2.3
N
P
B
'T' Runner
G
H
F

STEP 3.1: Insert drawer (Q) to footboard (B) until completely closed.
STEP 3.2: Tighten 'T' runner at footboard (B) to drawer slat (G) with CSK M4 x 16mm (8).
STEP 3.3: If drawer (Q) does not close properly, adjust the adjuster at the bottom of drawer slat support (H) up or down until the drawer (Q) closes tightly.
Page 4 of 6
ASSEMBLY INSTRUCTIONS
Adjuster
STEP 3.1
STEP 3.2
G
I
H
Q B
H
'T' Runner
Q
8
G
STEP 3.3

Adjuster
L
Page 5 of 6
ASSEMBLY INSTRUCTIONS
10
L
9
11
M
J
STEP 4.1: Attach the center slat (M), bed slat (J) to bed slat support (L).Tighten with JCBC M6 x 50mm (9) by using L key M4 (11).
STEP 4.2: Attach bed slat (J) & bed slat (K) and tighten to bed rail (F) with CSK M4 x 32mm (10).
STEP 4.2
STEP 4.1
N
A
P
B
F
J
K
L
M
Q

Page 6 of 6
ASSEMBLY INSTRUCTIONS
STEP 5.1
STEP 5.2
STEP 5.1: Insert the tip of slat cover (E) on the back of the footboard (B) until closely.
STEP 5.2: Use CSK M4 x 16mm (8) to fasten the slat cover (E) on the bed slat (K).
8
E
E
K