ACOEM Fixturlaser Laser Kit Assembly instructions

Fixturlaser Laser Kit
Quick tips

Fixturlaser Laser Kit
STEP 2
1. Rough Alignment
• Vertical: Place scale or straightedge on highest hub and
raise or lower the movable shaft to within 0,5 mm of the
stationary hub.
• Horizontal: Place scale or straightedge on hub nearest
to you and adjust the movable shaft to within 0,5 mm of
the stationary hub.
2. Correct Obvious Soft Foot
Loosen all the bolts and nd any obviously loose shim
packs. Add shims as needed to make a snug t.
3. Follow Tightening Sequence
Follow the same sequence throughout the alignment pro-
cess, and tighten in 3 passes: snug rst, 50% on second
pass, completely tight on the third pass (view sequence
on next page).

Fixturlaser Laser Kit
Bolt Tightening Sequence
4. Make a Final Soft Foot Correction
Loosen one bolt at a time and check for soft foot with a
0,05 mm shim or feeler gauge. Correct any foot with
0,05 mm or more of soft foot, then tighten the bolt
before proceeding to the next foot.

Fixturlaser Laser Kit
Set Up
1. Mount the ‘S’ sensor on the stationary shaft or
coupling hub and hand tighten the nut, use the tigtning
tool and tighten further. Turn the sensor on by pressing
the power button.
2. Mount the ‘M’ sensor on the movable shaft or
coupling hub and hand tighten the nut use the titning
tool and tighten further. Turn the sensor on by pressing
the power button.
Tighten the nut Press the power button
Start the Laser Kit App
1. Click on the Fixturlaser Laser kit app on your device
that starts the application.
2. The app will search for the sensor and connect to
them via Bluetooth. This will take between 5 to 15
seconds.
3. The lasers will turn on.

Fixturlaser Laser Kit
Aim the Lasers
1. Loosen the adjustment knob of the sensor and slide
the sensors up or down until the line laser beams hit the
middle of the opposite sensor, ne tune the line laser
beam with the adjustment wheel on the opposite side of
the sensor. Be precise so that the beam hits the window
as accurate as possible. Note that the sensors will be at
different elevations.
adjustment wheel
adjustment knob

Fixturlaser Laser Kit
Enter Dimensions
1. Press the yellow tape measure icon to open the
keypad.
2. Measure the indicated dimension to the nearest
1 mm for coupling dimensions or 2 mm for foot
dimensions and enter using the keypad. Continue
and enter all dimensions.
Tape measure icon
Measure Misalignment
1. Press the measurement mode icon. Rotate the
sensors to the 9:00 position and press the mea-
surement icon.
9:00 position Measurement icon
1 . 9:00
2 . 12:00
3. 3:00
Position the
sensors
within ± 3°

Fixturlaser Laser Kit
2. Rotate the sensors to the 12:00 position.Press the
measurement icon again to take the second
measurement.
12:00 position
3. Rotate the sensors to 3:00, measure. The results will
be displayed on screen.
Position the
sensors
within ± 3°

Fixturlaser Laser Kit
Evaluating the Results
1. Vertical results are displayed at the top of the screen,
horizontal results at the bottom.
2. Green coupling icons indicate values which are within
tolerance. Angular tolerance 0,08 mm/ 100 mm offset tol.
0,1 mm
3. Orange values are within 2x tolerance.
4. Red values are more the 2x than out of the tolerance
level.
Using the VertiZontal™Process
First Correct the Vertical Misalignment
1. Press the shim icon in the bottom right corner of the
screen.
2. Loosen all the bolts on the movable machine.
3. Follow screen instructions for removing or inserting
shims.
Shim icon

Fixturlaser Laser Kit
Next Correct the Horizontal Misalignment
1. First press the ‘live reading’ icon in the bottom right
corner of the screen.
2. To ensure the live readings are for the horizontal
direction make sure the sensors are at 3:00.
“Live reading” icon
3. Make the largest adjustment rst. The arrows indicate
the direction of adjustment.
4. Continue to adjust the movable machine, watching
the live readings, until both the angle and offset are
within tolerance.
5. Tighten the bolts using the tightening sequence
established in Pre-Alignment.
6. Some machines move laterally when tightening the
bolts. Make sure that the displayed values remain in
tolerance as you tighten the bolts.

Fixturlaser Laser Kit
Re-Measure
1. Press the re-measure icon.
2. Re-measure to verify the results are within toler-
ance. If they are not, repeat the Verti-ZontalTM
Correction Process.
Results/Save
1. Results Images are saved in the folder of photos on
your device automatically, when the auto save box is
ticked in the settings menu.
Auto save box

Fixturlaser Laser Kit
Fixturlaser Laser Kit Complete system:
Weight including all standard parts: 2,75 kg (6,06 lbs)
Displayed resolution: 0,01 mm (0,1 mil with “inch” settings.)
Case:
Dimension: 357 mm x 305 mm x 96 mm (14,1 in x
12 in x 3,8 in)
Sensors M5 1-0976/S5 1-0977
Wireless communication: Class I Bluetooth transceiver with
multi-drop capability. BLE Bluetooth
Low Energy (BT 4.0)
Operating time (Continuously measuring): 5 h
Weight: 156 g (5,5 oz)
Dimensions: 139 mm x 79 mm x 40 mm (5,5 in x
3,1 in x 1,6 in)
Environmental protection: IP 20
Measurement distance: 70 mm - 850 mm (2,7 in - 2,8 ft)
Detector: PSD (Single axis)
Detector area: 8,5 x 0,9 mm (0,3 x 0,04 in)
Measurement accuracy: 3% ± 0,01 mm
Inclinometer accuracy: ±2°
Shaft diameter: Ø 30-150 mm (1,2 - 5,9 in)
Rods: 2 pcs 150 mm (5,9 in)
Laser safty:

Fixturlaser Laser Kit
DECLARATION OF CONFORMITY
In accordance with the EMC Directive 2004/108/EC, the Low Voltage
Directive 2006/95/EC, including amendments by the CE-marking
Directive 93/68/EEC & EC directives RoHS 2011/65/EU.
Type of equipment: Alignment System
Brand name or trade mark: FIXTURLASER Laser Kit
Type designation(s)/Model no(s)
1-0976 FIXTURLASER M5
1-0977 FIXTURLASER S5
Manufacturer’s name, address, telephone & fax no
ACOEM AB - Box 7 - SE-431 21 Mölndal - Sweden
Tel: [phone] - Fax: [phone]
The following standards and/or technical specications, which
comply with good engineering practice in safety matters in force
within the EEA, have been applied:
Standard/Test report/Technical construction le/Normative document
Emission: EN 61000-6-3:2007.
Immunity: EN 61000-6-2:2005, EN 61000-4-2, -3, -4, -5, -6, -11.
EN 61010-1:2010
ISO9001:2008 Ref. No/ Issued by: DNV Certication AB Certication
No. 2009-SKM-AQ-2704/2009-SKM-AE-1419.
The laser is classied in accordance with the International Standard
IEC-60825-1:2007,
USA FDA Standard 21 CFR, Ch 1, Part 1040.10 and 1040.11 except for
deviations pursuant to laser notice No. 50, dated June 24, 2007.
Additional information
The product was CE-marked in 2014.
As manufacturer, we declare under our sole responsibility that the
equipment follows the provisions of the Directives stated above.
Date and place of issue:
Mölndal 2015-04-09
Signature of authorized person
Hans Svensson, CEO

Fixturlaser Laser Kit
Welcome to our world
Since the very beginning in 1984, Fixturlaser, (Brand of ACOEM) has
helped industries throughout the world to achieve more protable
and sustainable production. We have reached where we are today by
having the courage to think beyond the norm and follow slightly un-
conventional paths. We have had the courage to make mistakes and
nd new directions. Through our resolve, ambition and knowledge we
have become a global player and a leader in innovative, user-friendly
shaft alignment.
www.youtube.com/user/FIXTURLASER
www.alignmentknowledge.com
The Fixturlaser Laser Kit was designed to be used with the
Fixturlaser Laser Kit App.
View our following resources for more information.

www.alignmentknowledge.com
ACOEM AB
Östergårdsgatan 9
SE-431 53 Mölndal
SWEDEN
Phone [phone]
Fax [phone]
FIXTURLASER Laser Kit Quick Tips P-0272-GB 2015