Acond J1-01 User manual

Thank you very much for purchasing this Air Conditioner. Please
read this instructions carefully before using this appliance and keep
this manual for future reference.
意大利文

Remote controller 1
Operation instructions
Operation modes 3
Airflow direction control 4
Smart mode 5
Timer mode 6
Sleep mode 7
Super mode 7
Remote controller Instructions
(J1-01)

The remote controller transmits signals to the system.
Remote controller
1
1
2
4
3
12
5
6
11
7
8
9
10
SWING BUTTON
FAN BUTTON
ROOM TEMPERATURE
SETTING BUTTONS
SLEEP BUTTON
IFEEL BUTTON
CLOCK BUTTON
ON/OFF BUTTON
SMART BUTTON
MODE BUTTON
TIMER ON/OFF BUTTON
13 SUPER BUTTON
Used to start or stop the fast cooling/heating.
(Fast cooling operates at high fan speed with
18℃ set temp automatically ; Fast heating
operates at auto fan speed with 32℃ set temp
automatically)
Used to stop or start vertical adjustment
louver swinging and set the desired up/down
airflow direction.
Used to select fan speed in sequence
auto, high, medium or low.
Used to set or cancel Sleep Mode operation.
Press this button to start the I FEEL mode. Press
this button above 5 seconds , Turn off I FEEL mode.
(In I feel mode,the Air Conditioner operates basis
temperature sensor fitted in remote instead of
machine,Advice to use I FEEL mode and the
remote putwhere the indoor unit receive signal
easily.)
Used to set the current time.
Used to enter fuzzy logic operation directly,
regardless of the unit is on or off.
The appliance will be started when it is
energized or will be stopped when it is
in operation, if you press this button.
Press this button to select the operation mode.
Used to set or cancel the timer operation.
Remote controller
Indication symbols on LCD:
Note: Each mode and relevant function will be further specified in following pages.
Signal transmit
Dry indicator
Fan only indicator
Heating indicator
Cooling indicator
High fan speed
Medium fan speed
Low fan speed Display set temperature
Display set timer
Display current time
Auto fan speed Smart indicator
Sleep indicator
Ifeel
Super indicator
ON
OFF
14
Used to adjust the room temperature and
the timer, also real time.
10
11
12
13
14
3
4
ON/OFF
MODE FAN
SWING SLEEP SUPER
SMART IFEEL DIMMER
TIMER ON TIMER OFF CLOCK
ON
OFF
ON
OFF
1
2
6
7
5
8
9
DIMMER BUTTON
When you press this button, all the display of
indoor unit will be closed. Press any button to
resume display.

How to Insert the Batteries
How to Use
Remove the battery cover according to the arrow direction.
Insert new batteries making sure that the (+) and (-) of
battery are matched correctly.
Reattach the cover by sliding it back into position.
Note:
Use 2 LR03 AAA(1.5volt) batteries. Do not use rechargeable batteries.
Replace batteries with new ones of the same type when the display
becomes dim.
Storage and Tips for Using the Remote Controller
The remote controller may be stored mounted on a wall with a holder.
Note: The remote controller holder is an optional part.
2
To operate the room air conditioner, aim
the remote controller to the signal receptor.
The remote controller will operate the air
conditioner at a distance of up to 7m when
pointing at signal receptor of indoor unit.
Remote controller
Remote controller
Signal receptor
ON/OFF
MODE FAN
SWING SLEEP SUPER
SMART IFEEL DIMMER
TIMER ON TIMER OFF CLOCK
ON
OFF
ON
OFF

Each time MODE button is pressed, the operation mode
is changed in sequence:
Each time the "FAN" button is pressed, the fan speed is
changed in sequence:
18℃~32℃
Heating mode is NOT available for cooling only air conditioner.
HEATING
COOLING DRY FAN ONLY
Selecting mode
FAN mode
Auto High Medium Low
At "FAN ONLY" mode, only "High","Medium" and "Low" are available.
At "DRY" mode, Fan speed is set at "AUTO” automatically, "FAN" button
is ineffective in this case.
Setting temperature
Press once to lower temperature setting by 1℃
Press once to raise temperature setting by 1℃
Range of available set temperature
*HEATING, COOLING
DRY -7 ~ 7
unable to set
Turning on
SWING, SMART, TIMER ON, TIMER OFF, CLOCK, SLEEP and SUPER operation modes will be
specified in the following pages.
Press button, when the appliance receives the
signal, the RUN indicator of the indoor unit lights up.
Changing modes during operation, sometimes the unit does not response at once. Wait 3 minutes.
Wait 3 minutes before restarting the appliance.
During heating operation, air flow is not discharged at the beginning. After 2－5 minutes, the air flow will be discharged
until temperature of indoor heat exchanger rises.
FAN ONLY
Operation instructions
3
Operation modes
Note: Heating mode is NOT available for cooling only models.
Note: At “Dry” mode, the unit can decrease or rise 2℃ if you still
feel uncomfortable.(For the inverter you can choose from -7 to 7.)
ON/OFF
MODE FAN
SWING SLEEP SUPER
SMART IFEEL DIMMER
TIMER ON TIMER OFF CLOCK
ON
OFF
ON
OFF
13
4
2

SWING
ON/OFF
MODE FA N
SWIN G SLEEP SUPER
SMART IF EEL DIMMER
TIME R ON TIME R OFF CLOCK
ON
OFF
ON
OFF
5
Airflow direction control
Vertical airflow is automatically adjusted to a certain angle
in accordance with the operation mode after turning on the unit.
The direction of airflow can be
also adjusted to your own
requirement by pressing the
"SWING" button of the
remote controller.
Operation mode Direction of airflow
COOLING, DRY
*HEATING,
FAN ONLY
horizontal
downward
Vertical airflow control (with the remote controller)
Using remote controller to set various angles of flow or specific angle
as you like.
Swinging airflow
Pressing "SWING" button once, the vertical adjustment
louver will swing up and down automatically.
Desired direction airflow
Pressing the "SWING" button again when the louvers swing
to a suitable angle as desired.
Horizontal airflow control (with hands)
Turning the control rods of the
horizontal adjustment louvers to
change horizontal air flow as shown.
control rods of horizontal
adjustment louvers
Note: The shape of the unit may look different
from that of the air conditioner you have selected.
Do not turn the vertical adjustment louvers manually, otherwise malfunction may occur. If that happens, turn off the unit
first and cut off the power supply, then restore power supply again.
It is better not to let the vertical adjustment louver tilt downward for a long time at COOLING or DRY mode to prevent
condensed water from dripping.
Operation instructions
4
*Heating mode is only available for heat pump models.
Airflow direction control

Indoor temperature
SMART button is ineffective in SUPER mode.
Target temperature
21℃ or below 22℃
26℃Over 26℃
21℃-23℃
23℃-26℃
Your feeling
What you can do in SMART mode
button adjustment procedure
Operation mode
HEATING
FAN ONLY
DRY
Room temperature
decrease 2℃ after
operate for 3 minutes
COOLING
Press the SMART button, the unit enters SMART mode(fuzzy logic operation) directly regardless of
the unit is on or off. In this mode, temperature and fan speed are automatically set based on the
actual room temperature.
Uncomfortable
because of
unsuitable air
flow volume.
Uncomfortable
because of
unsuitable flow
direction.
Indoor fan speed alternates among
High, Medium and Low each time this
button is pressed.
Press it once, the vertical adjustment
louver swings to change vertical airflow
direction. Press it again, swings stops.
For horizontal airflow direction, please
refer to the previous page for details.
Operation mode and temperature are determined by indoor temperature
Note: Temperature, airflow and direction are controlled automatically in SMART mode.
However, For the on/off, you can choose from -2 to 2, for the inverter you can choose
from -7 to 7. if you still feel uncomfortable
Operation instructions
5
SMART mode
Heat pump models
Cooling only models
CLOCK button
You can adjust the real time by pressing CLOCK button, then
using and buttons to get the correct time, press
CLOCK button again the real time is set.
Indoor temperature Target temperature
23℃ or below
26℃
Over 26℃
23℃-26℃
Operation mode
FAN ONLY
DRY
Room temperature
decrease 2℃ after
operate for 3 minutes
COOLING
ON/OFF
MODE FA N
SWIN G SLEEP SUPER
SMART IFEE L DIMMER
TIME R ON TIMER OFF CLOC K
ON
OFF
FAN
SWING
Press MODE button cancel SMATR mode.

6
TIMER mode
The TIMER ON button can be used to set the timer to switch on the appliance at your
desired time.
Press the TIMER ON button and when "ON 12:00" flashes on the LCD display, you can
then press the or buttons to select the time you wish for the appliance to turn on.
Press the or button once to increase or decrease the time setting by 1 minute.
Press the or button 2 seconds to increase or decrease the time setting
by 10 minutes.
Press the or button for a longer time to increase or decrease the time by 1 hour.
Press the TIMER ON button again. Once you hear a "beep" and the indicator disappears,
the TIMER ON mode has been canceled.
A "beep" will sound.
Note: If you don't set the time in 10 seconds after you press the TIMER ON button, the remote control
will exit the TIMER ON mode automatically.
Note: It is similar to set TIMER OFF. You can make the appliance switch off automatically at
your desired time.
The TIMER indicator on the indoor unit lights up.
"ON" stops flashing.
After the set timer is displayed for 5 seconds the clock will be displayed on the LCD
of the remote control.
It is convenient to set the timer on with TIMER ON/OFF buttons when you go out in the
morning to achieve a comfortable room temperature when you get home. You can also
set the timer off at night to enjoy a good sleep.
Operation instructions
How to set the TIMER ON
How to cancel TIMER ON
Increase
Decrease
i)
it.
When your desired time is displayed on the LCD, press the TIMER ON button and confirm
ii)
iii)
ON

7
Operation instructions
SLEEP mode
SUPER mode
SLEEP mode can be set in COOLING ,HEATING mode. or DRYING
This function gives you a more comfortable environment for sleep.
The appliance will stop operation automatically after operating for 8 hours.
In SLEEP mode,
Fan speed is automatically set at low speed.
Set temperature will rise by 1 if the appliance operates in cooling ℃ at most
mode for 1 hour constantly, then keeps steady.
Set temperature will decrease by 3℃ at most if the appliance operates in
heating mode for 3 hours constantly, then keeps steady.
Note: In cooling mode, if room temperature is 26℃or above, set temperature
will not change.
Note: Heating is NOT available for cooling only air conditioner.
fast cooling
fast heating
SUPER mode can be set when the appliance is in operation or energized.
Fast cooling operates at high fan speed, changing the set temperature
automatically to 18
temperature automatically to 32 ℃.
℃;Fast heating operates at auto fan speed,changing the set
In SUPER mode, you can set airflow direction or timer. If you want to
escape from SUPER mode, press SUPER , MODE, FAN, ON/OFF,SLEEP
or TEMPERATURE SETTING button, the display will return to the original
mode.
Note:
The Appliance will continue working in SUPER mode for 15 minutes , if you don't
escape from it by pressing any of the buttons mentioned above.
SMART button is not available in SUPER mode.
SLEEP mode
SUPER mode
ON/OFF
MODE FAN
SWING SLEEP SUPER
SMART I FEEL DI MM ER
TIMER O N TIMER O FF CLOCK
ON
OFF
ON
ON
OFF
ON
OFF
SUPER mode is used to start or stop fast cooling or heating.
Operation without the Remote Controller
If you have lost the remote control unit or if it is malfunctioning,follow the steps below.
1.How to turn on the air conditioner:
Open the front panel(if necessary), press the ON/OFF button with a ball-point.Then the air conditioner
will automatically select the operation mode according to the room temperature.
2.How to turn off the air conditioner:
Open the front panel(if necessary), press ON/OFF button with a ball-point.
Note:Do not press the ON/OFF button too long,as it may cause the air conditioner to operate abnormally.
Tips for energy saving
Operation without the Remote ControllerOperation without the remote control
If the air inlet and air outlet is blocked it might affect the normal heat exchange of the air conditioner and even cause damage to the
appliance.When the air conditioner is operating in Cooling Mode during the daytime,please use a sun shield or curtains to keep
from direct sunlight from entering into the room.IF the walls and ceiling are irradiated by sunlight,it will take a long time to achieve
the set temperature during cooling opertaion.Clean the air-filters at a certain time(about every two weeks)and keep the air-filters
clean to to ensure normal heat exchange of the indoor unit.
Keep the door and windows well closed when the air-conditioner is running to avoid loss of heat.
Note: Press SUPER ,SMART, MODE,SLEEP or FAN button cancel SLEEP mode.