Futaba R7108sb Installation instructions

1M23Z07702

WEB FULL MANUAL

2

●Introduction �� 4

●Support and Service �� 4

●Application, Export, and Modication�� 4

●Compliance Information Statement �� 5

●Denitions of Symbols�� 5

●Safety Precautions (do not operate without reading)�� 6

●Features �� 10

●Contents and Technical Specications�� 10

●Transmitter Controls�� 11

●Transmitter's Antenna �� 13

●Transmitter Lipo Battery LT2F2000B�� 14

●How to turn transmitter power ON/OFF �� 16

●Touch Display�� 17

●HOME/EXIT and U.MENU/MON �� 17

●Lock Display�� 18

●RF o mode �� 18

●Switch (SA-SH) �� 19

●Volume �� 20

●Slider�� 20

●Digital Trims (T1-T4) �� 21

●Monitor LED display�� 22

●Stick Control �� 22

●Stick Control: Airplane Example�� 23

●Stick Control: Helicopter Example�� 24

●Stick Control: Multicopter Example �� 25

●Stick Adjustment �� 26

●Stick Mode�� 27

●micro SD card �� 28

●Connector/Plug �� 29

●Receiver Nomenclature �� 30

●Receiver's Antenna Installation�� 33

●Safety precautions when you install receiver and servos�� 34

●S.BUS/S.BUS2 Installation �� 35

●S.BUS2 System�� 36

●S.BUS2 Sdevice setting�� 37

●Home Screen �� 38

●Link Procedure �� 39

●After Setting �� 40

●Model ID�� 41

●Range Testing Your R/C System�� 42

●Model basic setting procedure�� 43

●Servo Connection by Model Type �� 48

Airplane/Glider�� 48

Helicopter�� 52

Multicopter �� 52

TABLE OF CONTENTS

SYSTEM MENU�� 53

Display ��54

Sound volume��55

System timer��55

H/W setting��56

Battery ��57

Range check �� 57(→42)

S.Bus servo ��58

Information ��61

LINKAGE MENU �� 62

Servo monitor��63

Model select��64

Model type��67

Servo reverse��69

End point ��70

Servo speed��71

Sub-trim ��71

Function��72

Fail safe��74

System type ��75

Trim setting ��77

Throttle cut��78

Idle down ��79

Swash ring (Heli only)��80

Swash (Heli only, except H-1)��81

Stick alarm ��83

Timer ��84

Function name ��86

Telemetry system ��87

Sensor��89

Telemetry��92

Telemetry:Receiver [Battery] ��93

Telemetry:Receiver [Ext-batt]��94

Telemetry:Temperature ��95

Telemetry:RPM sensor��96

Telemetry:Altitude ��97

Telemetry:Altitude [Variometer] ��98

Telemetry:Voltage [Battery] ��101

Telemetry:Voltage [Ext-batt]��102

Telemetry:GPS [Distance] ��103

Telemetry:GPS [Speed]��105

Telemetry:GPS [Altitude, Variometer, Position]��106

Telemetry:Servo sensor [Current] ��107

Telemetry:Servo sensor [Temperature, Angle] ��108

3

Telemetry:Current sensor [Current] ��109

Telemetry:Airspeed sensor [Airspeed] ��110

Tele. setting (Telemetry setting)�� 111

Trainer��113

Warning setting�� 116

User menu setting ��117

Data reset��118

MODEL MENU (Airplane/Glider)

Condition select ��120

AFR ��122

Dual rate��123

Prog, mixes (Program mixing) ��124

Aileron dierential ��126

Flap setting��127

AIL → Camber ap��128

AIL → Brake ap ��129

Aileron → Rudder ��130

Elevator → Camber ��131

Camber mixing ��132

Airbrake → ELE ��134

Camber ap → ELE��135

Rudder → Aileron ��136

Rudder → Elevator��137

Buttery��138

Trim mix 1/2��141

Snap roll (Airplane only) ��142

Air brake (Airplane only) ��143

Gyro ��144

Ailevator ��146

Acceleration ��147

Motor ��148

V-tail��149

Winglet��150

MODEL MENU (Helicopter)

Condition select ��152

AFR ��154

Dual rate��155

Prog, mixes (Program mixing) ��156

Pitch curve��158

Throttle curve ��161

Acceleration ��163

Throttle hold ��164

Swash mixing ��165

Throttle mixing ��166

Pitch → Needle��167

Pitch → Rudder (Revolution mixing) ��168

Gyro (Helicopter)��169

Governor ��171

Gyro setting CGY755 CGY760R ��173

Wired connection:Advanced setting �� 174

Wireless tunings �� 175

Home Screen�� 176

Basic Menu �� 178

S.BUS Basic Menu �� 179

Swash Basic �� 180

Flight Tune (Aileron/Elevator Basic settings) �� 184

Rudder Basic �� 187

Govenor Basic �� 188

Expert Menu �� 191

Rudder Expert �� 192

Flight Tune Expert (Aileron/Elevator Expert settings)�� 195

Swash Detail �� 196

Govenor Expert�� 199

MODEL MENU (Multicopter)

Condition select ��202

AFR ��204

Dual rate��205

Prog, mixes (Program mixing) ��206

Common Operations used in function setup

screen�� 208

●Operations value setting��208

●Operations related to ight conditions ��208

●Operations related to ne tuning VR��209

●Operations related to servo speed ��210

●Curve setting operation��211

●Switch selection method ��215

●PC Port ��219

●RealFlight Connection method��219

●Updating ��221

●T14SG/FX-22/T12K ⇒T16IZ CONVERSION ��223

4

Thank you for purchasing a Futaba®FASSTest-2.4 GHz* T16IZ series digital proportional R/C system. This system is

extremely versatile and may be used by beginners and pros alike. In order for you to make the best use of your system

and to y safely, please read this manual carefully. If you have any diculties while using your system, please consult

the manual, our online Frequently Asked Questions (on the web pages referenced below), your hobby dealer, or the

Futaba Service Center.

*FASSTest: Futaba Advanced Spread Spectrum Technology extend system telemetry

Due to unforeseen changes in production procedures, the information contained in this manual is subject to change

without notice.

Support and Service: It is recommended to have your Futaba equipment serviced annually during your hobby’s “o

season” to ensure safe operation.

In North America

Please feel free to contact the Futaba Service Center for assistance in operation, use and programming. Please be

sure to regularly visit the T16IZ Frequently Asked Questions web site at www.futabausa.com/. This page includes

extensive programming, use, set up and safety information on the T16IZ radio system and is updated regularly. Any

technical updates and US manual corrections will be available on this web page. If you do not nd the answers to your

questions there, please see the end of our F.A.Q. area for information on contacting us via email for the most rapid and

convenient response.

Don’t have Internet access? Internet access is available at no charge at most public libraries, schools, and other public

resources. We nd internet support to be a fabulous reference for many modelers as items can be printed and saved for

future reference, and can be accessed at any hour of the day, night, weekend or holiday. If you do not wish to access

the internet for information, however, don’t worry. Our support teams are available Monday through Friday 8-5 Central

time to assist you.

For Service :

FUTABA Corporation of America

2681 Wall Triana Hwy Huntsville, AL 35824, U.S.A.

Phone:1-256-461-9399 FAX:1-256-461-1059

https://www.futabausa.com/

E-mail: [email protected]

Outside North America

Please contact your Futaba importer in your region of the world to assist you with any questions, problems or service

needs. Please recognize that all information in this manual, and all support availability, is based upon the systems

sold in North America only. Products purchased elsewhere may vary. Always contact your region’s support center for

assistance.

INTRODUCTION

Application, Export, and Modication

1. This product may be used for unmanned aerial vehicle use. It is not intended for use in any application other than

unmanned aerial vehicle control. The product is subject to regulations of the Ministry of Radio/Telecommunications

and is restricted under Japanese law to such purposes.

2. Exportation precautions:

(a) When this product is exported from the country of manufacture, its use is to be approved by the laws governing

the country of destination which govern devices that emit radio frequencies. If this product is then re-exported to other

countries, it may be subject to restrictions on such export. Prior approval of the appropriate government authorities may

be required. If you have purchased this product from an exporter outside your country, and not the authorized Futaba

distributor in your country, please contact the seller immediately to determine if such export regulations have been met.

(b) Use of this product with anything other than models may be restricted by Export and Trade Control Regulations,

and an application for export approval must be submitted. This equipment must not be utilized to operate equipment

other than radio controlled models.

3. Modification, adjustment, and replacement of parts: Futaba is not responsible for unauthorized modification,

adjustment, and replacement of parts on this product. Any such changes may void the warranty.

“Please visit www.futabausa.com to create and submit a service

ticket for warranty, repair, or check up work.”

5

Compliance Information Statement (for U.S.A.)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received,

including interference that may cause undesired operation.

(3)RF Radiation Exposure Statement (For T16IZ)

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This transmitter

must not be co-located or operating in conjunction with any other antenna or transmitter.

RF Radiation Exposure Statement (For R7108SB)

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance 20cm between the radiator & your body.

The responsible party for the compliance of this device is:

FUTABA Corporation of America

2681 Wall Triana Hwy Huntsville, AL 35824, U.S.A.

Phone:1-256-461-9399 FAX:1-256-461-1059

https://www.futabausa.com/

E-mail: [email protected]

CAUTION:

To assure continued FCC compliance:

Any changes or modications not expressly approved by the grantee of this device could void the user’s authority to

operate the equipment.

Compliance Information Statement (for Canada)

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This transmitter

must not be co-located or operating in conjunction with any other antenna or transmitter.

French:

Cet appareil radio est conforme au CNR d’Industrie Canada. L’utilisation de ce dispositif est autorisée seulement aux

deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit être prêt à

accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement

du dispositif.

Cet équipement est conforme aux limites d'exposition au rayonnement du CI établies pour un environnement non

contrôlé. Cet émetteur ne doit pas être co-situé ou fonctionner conjointement avec une autre antenne ou émetteur.

Declaration of Conformity (for EU)

Hereby, Futaba Corporation declares that the radio equipment type is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address:

http://www.rc.futaba.co.jp/english/dl/declarations.html

6

Flying Safety

Where to Fly

We recommend that you y at a recognized model airplane ying eld. You can nd model clubs and elds by

asking your nearest hobby dealer, or, in the US, by contacting the Academy of Model Aeronautics.

The national Academy of Model Aeronautics (AMA) has more than 2,500 chartered clubs across the country.

Through any one of them, instructor training programs and insured newcomer training are available. Contact the

AMA at the address or toll-free phone number below.

Academy of Model Aeronautics

5161 East Memorial Drive

Muncie, IN 47302

Tele. (800) 435-9262

Fax (765) 289-4248

or via the Internet at http:\\www.modelaircraft.org

Always pay particular attention to the ying eld’s rules, as well as the presence and

location of spectators, the wind direction, and any obstacles on the eld. Be very careful

ying in areas near power lines, tall buildings, or communication facilities as there may be

radio interference in their vicinity.

Precautions

Application, Export, and Modiﬁcation Precautions.

1. This product is only designed for use with radio control models. Use of the product described in this instruction manual is limited to

radio control models.

2. Export precautions:

a) When this product is exported, it cannot be used where prohibited by the laws governing radio waves of the destination country.

b) Use of this product with other than models may be restricted by Export and Trade Control Regulations.

3. Modiﬁcation, adjustment, and parts replacement:

Futaba is not responsible for unauthorized modiﬁcation, adjustment, or replacement of parts on this product.

■ No part of this manual may be reproduced in any form without prior permission.

■ The contents of this manual are subject to change without prior notice.

■ The contents of this manual should be complete, but if there are any unclear or missing parts please contact a Futaba Service

Center.

■ Futaba is not responsible for the use of this product by the customer.

■ Company and product names in this manual are trademarks or registered trademarks of the respective company.

For safe use

Please observe the following precautions to ensure safe use of this product at all times.

Meaning of Special Markings:

The parts of this manual indicated by the following marks require special attention from the standpoint of safety.

DANGER - Procedures which may lead to dangerous conditions and cause death/serious injury if not carried out properly.

WARNING - Procedures which may lead to a dangerous condition or cause death or serious injury to the user if not carried out properly,

or procedures where the probability of supercial injury or physical damage is high.

CAUTION - Procedures where the possibility of serious injury to the user is small, but there is a danger of injury, or physical damage, if

not carried out properly.

= Prohibited = Mandatory

WARNING: Always keep electrical components away from small children.

7

Flying Precautions

WARNING

Never grasp the transmitter antenna while ying.

■ The transmitter output may drop drastically.

Always make sure that all transmitter stick move-

ments operate all servos properly in the model prior to

flight. Also, make sure that all switches, etc. function

properly as well. If there are any di󱐰culties, do not use

the system until all inputs are functioning properly.　

Never y in range check mode.　

■ In the dedicated range test range check mode, the transmitter

output range is reduced and may cause a crash.

While operating, never touch the transmitter with, or

bring the transmitter near, another transmitter, a cell-

phone, or other wireless devices.

■ Doing so may cause erroneous operation.

Do not point the antenna directly toward the aircraft

during ight.　

■ The antenna is directional and the transmitter output is

weakest. (The strength of the radio waves is greatest from the

sides of the antenna.)

Never y on a rainy day, when the wind is strong, or

at night.　

■ Water could lead to failure or improper functionality and poor

control of the aircraft which could lead to a crash.

Never turn the power switch o󱐯 during ight or while

the engine or motor is running.　

■ Operation will become impossible and the aircraft will crash.

Even if the power switch is turned on, operation will not begin

until transmitter and receiver internal processing is complete.

Do not start the engine or motor while wearing the

neck strap.　　

■ The neck strap may become entangled with the rotating

propeller, rotor, etc. and cause a serious injury.

Do not fly when you are physically impaired as it

could pose a safety hazard to yourself or others.

Do not y at the following places:　　　

■ Near another radio control ying eld.

■ Near or above people.

■ Near homes, schools, hospitals or other places where people

congregate.

■ Near high voltage lines, high structures, or communication

facilities.

When setting the transmitter on the ground during

ight preparations, do not stand it upright.

■ The transmitter may tip over, the sticks may move and the

propeller or rotor may rotate unexpectedly and cause injury.

Do not touch the engine, motor, or ESC during and

immediately after use.　

■ These items may become hot during use.

For safety, y so that the aircraft is visible at all times.

■ Flying behind buildings or other large structures will not only

cause you to lose sight of the aircraft, but also degrade the RF

link performance and cause loss of control.

From the standpoint of safety, always set the fail safe

function.　　　

■ In particular, normally set the throttle channel to idle. For a

helicopter, set the throttle channel to maintain a hover.

When flying, always return the transmitter setup

screen to the Home screen.

■ Erroneous input during ight is extremely dangerous.

Always check the remaining capacity of the trans-

mitter and receiver batteries before each ying session

prior to ight.　

■ Low battery capacity will cause loss of control and a crash.

Always check operation of each control surface and

perform a range test before each flying session. Also,

when using the trainer function, check the operation of

both the teacher and student transmitter.　

■ Even one incorrect transmitter setting or aircraft abnormality

can cause a crash.

Before turning on the transmitter:

1. Always move the transmitter throttle stick position to the

minimum (idle) position.　

2. Turn on the transmitter rst and then the receiver.

When turning off the transmitter’ s power switch

after the engine or motor has stopped (state in which it

will not rotate again):

1. Turn o󱐯 the receiver power switch.　

2. Then turn o󱐯 the transmitter power switch.

■ If the power switch is turned on/oﬀ in the opposite order, the

propeller may rotate unexpectedly and cause a serious injury.

■ Also always observe the above order when setting the fail safe

function.

When adjusting the transmitter, stop the engine ex-

cept when necessary. In the case of a motor, disconnect

the wiring that allows it to continue operation. When

doing so, please exercise extreme caution. Ensure that

the aircraft is secured and that it will not come into con-

tact with anything or anyone. Ensure that the motor will

not rotate prior to making any adjustments.

■ Unexpected high speed rotation of the engine/motor may

cause a serious injury.

8

Do not recharge a battery that is damaged, deterio-

rated, leaking electrolyte, or wet.　

Do not allow the charger or battery to become wet.

■ Do not use the charger when it or your hands are wet. Do not

use the charger in humid places. 　　　

Do not short circuit the battery.　　

Do not solder, repair, deform, modify, or disassemble

the battery and/or battery charger.　　

Do not drop the battery into a re or bring it near a re.

Do not charge and store the battery in direct sunlight

or other hot places.　　　

Do not charge the battery if it is covered with any ob-

ject as it may become very hot.

Do not use the battery in a combustible environment.　

■ The combustibles may could ignite ignite and cause an

explosion or re.

Always charge the battery before each ying session.

　■ If the battery goes dead during ight, the aircraft will crash.

Insert the power cord plug rmly into the recep-

tacle up to its base.

Battery and Charger Handling Precautions

DANGER

Always use the charger with the specified power

supply voltage.

If the battery liquid should get in your eyes, do not

rub your eyes, but immediately wash them with tap wa-

ter or other clean water and get treated by a doctor.

■ The liquid can cause blindness. 　

Do not touch the charger and battery for any length

of time during charging.　

■ Doing so may result in burns. 　　　

Do not use a charger or battery that has been dam-

aged.　　

If any abnormalities such as smoke or discoloration

are noted with either the charger or the battery, remove

the battery from the transmitter or charger and discon-

nect the power cord plug and do not use the charger.　

■ Continued use may cause re, combustion, generation of heat,

or rupture.

Do not subject the batteries to impact.

■ Doing so may cause re, combustion, generation of heat,

rupture, or liquid leakage.

Use and store the battery and battery charger in a se-

cure location away from children.　

■ Not doing so may cause electric shock or injury.

WARNING

If the battery leaks liquid or generates an abnormal

odor, immediately move it to a safe place for disposal.

■ Not doing so may cause combustion.

If the battery liquid gets on your skin or clothing, im-

mediately ush the area with tap water or other clean

water.

■ Consult a doctor. The liquid can cause skin damage.

After charging, disconnect the charger from the re-

ceptacle.　

When recycling or disposing of the battery, isolate

the terminals by covering them with tape.

■ Short circuit of the terminals may cause combustion,

generation of heat or rupture.

Do not y with the USB AC adapter for charging con-

nected.

Do not use the battery with devices other than the

corresponding transmitter.

Do not place heavy objects on top of the battery or

charger. Also, do not place the battery or charger in any

location where it may fall. 　　

■ Doing so may cause damage or injury.

Do not store or use the battery where it is dusty or

humid.　

CAUTION

■ Insert the power cord plug into the receptacle only after

eliminating the dust.

After the transmitter has been used for a long time,

the battery may become hot. Do not touch the battery

immediately.

■ Not doing so may cause a burn.

Do not bend or pull the cord unreasonably and do

not place heavy objects on the cord.

■ The power cord may be damaged and cause combustion,

generation of heat, or electric shock.

1. Replacement of a battery with an incorrect type that can defeat a

safeguard.

2. Disposal of a battery into fire or a hot oven, or mechanically

crushing or cutting of a battery, that can result in an explosion.

3. Leaving a battery in an extremely high temperature surrounding

environment that can result in an explosion or the leakage of

ammable liquid or gas.

4. A battery subjected to extremely low air pressure that may result

in an explosion or the leakage of ammable liquid or gas.

Temperature

Low temp. protection -10 ± 5 ° C

High temp. protection 60 ± 5 ° C

Temperature protection for battery charge:

9

Never disassemble or modify the SD card.　

Do not bend, drop, scratch or place heavy objects on

the SD card.

If smoke or an abnormal odor emanates from the card,

immediately turn o󱐯 the transmitter power.

Since the SD card is an electronic device, be careful of

static electricity.　

■ Static electricity may cause erroneous operation or other

trouble.

Do not use the SD card near radio and television sets,

audio equipment, motors and other equipment that

generates noise.　

■ Doing so may cause erroneous operation.

Do not store the SD card in the following places:

・ Where the humidity is high

・ Where the temperature di󱐯erence is severe

・ Where it is very dusty

・ Where the card will be exposed to shock and vibration

・ Near speakers and other magnetic devices

micro SD Card (Commercial Product) Handling Precautions

WARNING

CAUTION

*Read the instruction manual supplied with the SD card for details.

● Recorded data

The data recorded on the SD card cannot

be compensated regardless of the contents

or cause of the trouble or obstruction.

Futaba does not perform data restoration

or recovery work.

Do not use the SD card where it may be exposed to

water, chemicals, oil, or other uids.　

■ Doing so may cause a re or electric shock by short circuiting.

Do not insert foreign matter into the transmitter card slot.

■ Doing so may cause erroneous operation.

Do not expose the card to shock and vibration and do

not remove the card from the card slot while data is be-

ing written or read.　

■ The data may be damaged or lost.

Keep wireless equipment, batteries, aircraft, etc.

away from children.　

Do not directly expose plastic parts to fuel, oil, ex-

haust gas, etc.　

■ If left in such an environment, the plastic may be damaged.

■ Since the metal parts of the case may corrode, always keep

them clean.

Join the Academy of Model Aeronautics.　

■ The Academy of Model Aeronautics (AMA) provides guidelines

and liability protection should the need arise.

Storage and Disposal Precautions

Other Precautions

WARNING

CAUTION

Do not store wireless devices in the following places:

・ Where it is extremely hot (40℃ [104 ℉ ] or higher) or

cold (-10℃ [14 ℉ ] or lower)

・ Where the equipment will be exposed to direct sun-

light

・ Where the humidity is high

・ Where vibration is prevalent

・ Where it is very dusty

・ Where the device may be exposed to steam and heat

CAUTION

When the device will not be used for a long time, re-

move the batteries from the transmitter and aircraft and

store them in a dry place where the temperature is be-

tween 0℃ and 25℃ [32 ℉ and 77 ℉].

■ Leaving batteries inside your model and radio when they are not

being used for long periods will result in battery deterioration,

liquid leakage and other damage.

Always use genuine Futaba products such as trans-

mitter, receiver, servo, ESC, etc.

■ Futaba is not responsible for damage sustained by combination

with parts other than Futaba Genuine Parts. Use the parts

specied in the instruction manual and catalog.

10

Features

FASSTest system

The T16IZ transmitter has adopted the bidirectional communication system "FASSTest". Data from the receiver can be checked in

your transmitter. FASSTest is a maximum 18 channels 2.4 GHz dedicated system.

Color touch screen LCD

T16IZ has an HVGA 4.3 inch, full-color, backlit LCD touch screen. The screen is transflective which enables both indoor and

outdoor visibility.

S.BUS2 system

By using the S.BUS2 system multiple servos, gyros and telemetry sensors are easily installed with a minimum amount of cables.

Model types

Multicopter. 8 swash types are available for helicopters. 7 wing types and 3 tail types are available for airplanes and gliders.

Functions and mixing functions necessary for each model type are set in advance at the factory.

Lithium-ion polymer battery

T16IZ is operated by a 7.4 V/2,000 mAh Lithium-ion polymer battery.

micro SD card (Secure Digital memory card) (Not included)

Model data can be saved to an micro SD card (SD:32MB-2GB SDHC:4GB-32GB). When T16IZ transmitter software files are

released, the software can be updated by using an micro SD card update.

Edit button

Two edit buttons are provided, and the operating screen can be immediately “Returned” to the HOME screen during operation.

Setting operation can be performed easily by combining this button with a touch sensor.

Vibration function

Selects a function that alerts the operator to various alarms by vibrating the transmitter in addition to sounding a buzzer.

Speech function

A function is equipped which allows the system to provide telemetry data audibly. This function can also be utilized with

commercially available earphones.

Contents and Technical Specications

(Specications and ratings are subject to change without notice.)

• T16IZ Transmitter

• R7108SB Receiver

• LT2F2000B LiPo Battery

Transmitter T16IZ

(2-stick, 18-channel, FASSTest-2.4 GHz system)

Transmitting frequency: 2.4 GHz band

System: FASSTest 18CH/FASSTest 12CH/S-FHSS/T-FHSS/

FASST MULT(Europe is not supported)/FASST 7CH(Europe is not supported) switchable

Power supply: 7.4 V LT2F2000B LiPo battery

Frequency band: 2.4 GHz

RF power output : 100 mW EIRP

Receiver R7108SB

(FASSTest-2.4 GHz system, Dual Antenna Diversity, S.BUS/S.BUS2 system)

Power requirement: 3.7 V-7.4 V battery or regulated output from ESC, etc. (*1)

Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)

Weight: 0.42 oz. (12.0 g)

Frequency band: 2.4 GHz

RF power output: 25 mW EIRP

(*1) When using ESCs make sure that the regulated output capacity meets your usage application.

Note: This set does not include a charger. Use a commercially available USB charger AC

adapter (USB-A type 5 V-2 A) or the Futaba optional USB AC adapter.

Note: The battery in the T16IZ transmitter does not arrive already attached to the battery

connector. Please connect the battery connector before use.

• USB Cable

• Hex Key

• Tx Strap

• Short Manual

*The contents may vary on the type of set.

11

Transmitter Controls

● Stick ● Stick

● Power Switch

● Hook

● U.MENU/MON. Button

（User menu/Servo monitor）

● HOME/EXIT Button

● Color LCD Touch Display

● Digital trim

T1-T4

● Antenna ● micro SD Slot

● PC Port

● Monitor LED

● Left Dial (LD) ● Right Dial (RD)

● Switch

SC.SD.SG.SH

● Switch

SA.SB.SE.SF

J2J3

J1J4

Top

Front

The transmitter

can be used as a

game controller by

connecting it to a

computer with a USB

cable. (Some games

cannot be used.)

12

● Left Slider

LS

● Right Slider

RS

● Battery cover ● Trainer port

● S.I/F Port

　（S.BUS setting）

● Kickstand

● Charging Port

● Charging LED

● Earpone

Jack

● Stick tension adjustment port

Back

Bottom

The LCD displays shown in this manual may vary from your own,

depending upon your model type. LCD displays may also vary as a

result of version upgrades or other changes.

The angle when the transmitter is

placed can be changed by rotating

the swing handle and tightening

the screw.

13

Transmitter's Antenna

As with all radio frequency transmissions, the strongest area of signal transmission is from the sides of

the transmitter's antenna. As such, the antenna should not be pointed directly at the model. If your ying

style creates this situation, easily move the antenna to correct this situation.

Rotating antenna

The antenna can be rotated 90 degrees and angles 90 degrees.

Forcing the antenna further than this can damage it. The

antenna is not removable.

CAUTION

Do not grasp the transmitter antenna

during ight.

■Doing so may degrade the quality of the RF

transmission to the model.

Do not carry the transmitter by the

antenna.

■The antenna wire may break, making operation

impossible.

Do not pull the antenna forcefully.

■The antenna wire may break, making operation

impossible.

1

2

3 4 5

Low power

High power High power

If you y with your

transmitter facing

the model at the

angle shown in the

illustration, bend the

antenna 90 degrees.

Do not y your model

with the antenna's

tip pointing in its

direction.

Stand up：1 ⇒ 5

Storage： 5 ⇒ 1

*Rotate rst *Stand up next

14

Transmitter LiPo Battery LT2F2000B

Installing/removing the LT2F2000B

Install the battery into the transmitter

Close the battery cover completely

Be careful not to pinch

the wiring

Connect the battery

connector

Press the tab to

open the battery

cover.

First insert two tabs

Remove the

battery cover

Tab

Battery cover

This connector connects to

the transmitter. LT2F2000B

LiPo Battery

Press the tab to

close the battery

cover.

Click ! Click !

15

WARNING

Be careful not to drop the battery.

Never disconnect the battery connector

from the T16IZ transmitter after

turning o󱐯 the power until the screen is

completely blank and the transmitter has

shut down completely.

* Internal devices such as memories may be damaged.

* If there is any problem, the message "Backup Error" will

be shown the next time when you turn on the power of the

transmitter. Do not use the transmitter as it is. Send it to the

Futaba service center.

WARNING

Do not plug and unplug the charger

when your hands are wet.

*It may cause an electric shock.

Do not overcharge/overdischarge the

battery.

*Overcharging/Overdischarging a battery can result in

burns, re, injuries, or loss of sight due to overheating,

breakage, or electrolyte leakage.

CAUTION

When the charger is not in use,

disconnect it from the AC outlet.

* Do this to prevent accidents and to avoid overheating.

Charging a battery

Charging LED

Red: Charging

Green: Full

Use a commercially available

USB charger AC adapter

USB-A type 5 V-2 A

USB Cable

This set is not equipped with an AC adapter

for charging. Must be purchased separately.

● AC adapter USB-A type 5 V - 2 A

or

● Futaba option AC adapter USB type

Access the charge port by

ipping the rubber cover

on the bottom of the

transmitter.

16

Power OFFPower ON

Throttle Stick Low

Power Switch Power Switch

Long Push

Push

1. Turn on the transmitter power switch.

2. Turn on the receiver or speed control power switch.

Always be sure the motor/engine is stopped.

1. Turn oﬀ the receiver or speed control power switch.

2. Then turn oﬀ the transmitter power switch.

ON OFF

OFF

ON

Turning on the power switches

If the power switches are turned oﬀ in the opposite order the model may unexpectedly run out of control and

cause a very dangerous situation.

Turning o the power switches

How to turn transmitter power ON/OFF

When turning on the power, the T16IZ transmitter will begin emitting RF automatically after it conrms

the surrounding RF conditions. The status of the transmitter is displayed by LED at the upper part of the

front of a T16IZ.

*If THR stick is high, a WARNING screen will appear. Another warning will appear if a power

supply is attached. (In Multicopter mode, the THR position alarm will not appear.)

If the "Thr position" alarm displays

*If the throttle stick is in the high position when the

power is turned ON

Warning alarm

Tap this to stop the alarm

and RF signal. Only panel

screen operation is active, the

transmitter will not link to any

receiver.

When the alarm activates, lower the throttle stick

before turning the receiver power ON.

*If the power is turned ON when the idle-up, air brake,

etc., switches are ON, the above warning will display.

Ensure the relevant switches are turned OFF.

17

Touch Display

HOME/EXIT and U.MENU/MON.

Tap the panel with your nger to navigate.

*Plastic lm is attached to the Touch Display. Please

be careful so that you don't scratch the Touch

Display with anything hard such as a metal object.

Don't push the Touch Display with excessive force

or drop anything on the panel.

*Although you may nd some air bubbles under the

plastic panel due to environmental changes such

as temperature, it is not a defect and will cause no

problems.

*Color LCD is made from many pixels. Some

pixels hold lighting. Moreover, some pixels go out.

And a screen may flicker. Such condition is the

characteristics of color LCD. It is not failure.

Tapping the settings buttons for

each value on the settings screen

will cause value input buttons to

appear at the top of the panel.

Value input buttons display at the

top of the display.

Pressing and holding a value will

return it to its default setting.

Small change

in value

Large change

in value

Large change

in value

HOME/EXIT

Press Return to the

previous screen

Press and hold Return to the

home screen

Press from

HOME screen. To Telemetry

display

Press and hold

from HOME

screen.

Panel lock / Lock

release

Press To user menu

display

Press and

hold To servo monitor

display

U.MENU/MON.

18

Lock Display

Temporarily activating this function makes it impossible to change data by accidental input during

ight.

RF o mode

Model operation is disabled, but display operation without RF signal output is allowed. (Reduces

battery power consumption during set-up.)

Display unlock

HOME/EXIT Press and hold

Restart the power

to transmit RF

signals.

"RF o󱐯" Model

operation is not

possible, but only

panel operation is.

U.MENU/MON.

Press and

Power ON

Lock Display

How to lock

How to unlock

1. With the home screen displayed.

2. Press the HOME/EXIT button for about 1

second. "Key Icon" is displayed and the

keys will be disabled.

1. Press the Home/Exit button for about 1

second, and the display will then become

unlocked.

CAUTION

The T16IZ's touch screen is very sensitive. To

avoid accidentally activating it during a flight, it

is suggested that it be locked. Due to the touch

screen's sensitivity, allowing it to be touched

during flight by a neck strap hook, servo extension,

or even your hand could be dangerous. Please use

the Touch Display lock for added safety during

flight.

19

SA : 3 positions; Alternate;

Short lever

SD : 3 positions; Alternate;

Short lever

SB : 3 positions; Alternate;

Long lever

SC : 3 positions; Alternate;

Long lever

SF : 2 positions; Alternate;

Long lever

Alternate2 positions Momentary3 positions

SH : 2 positions; Momentary;

Long lever

SG : 3 positions; Alternate;

Short lever

SE : 3 positions; Alternate;

Short lever

Switch (SA-SH)

*Self retum

20

LS RS

Slider

LS (Left), RS (Right):

The Linear Slider LS and RS oer analog input.

*The T16IZ transmitter beeps when the lever comes to the center.

*You can select a slide lever and set the movement direction on the setting screen of mixing functions.

The volume LD and RD knobs allow

analog input.

*The T16IZ transmitter beeps when the volume

knob reaches the center position.

*You can use each setting screen of the mixing

functions to select volumes and define the

direction of movement.

Volume

LD RD

FUTABA R7108SB Installation instructions

Popular Remote Control manuals by other brands