Acrosser Technology AR-B1543 User manual

Page1of4 AR-B1543 Manual
AR-B1543 Manual
Version 1.4
1. SETTING UP THE SYSTEM
1.1 PACKING LIST
! The quick setup manual
! 1 AR-B1543 CPU board
! 1 Hard disk drive adapter cable for 3.5” HDD
! 1 Hard disk drive adapter cable for 2.5” HDD.
! 1 Floppy disk drive adapter cable
! 1 Parallel port adapter cable & 1 RS-232C interface
cable mounted on one bracket
! 1 Software utility CD
! AR-B9462A can supported Compact Flash (option).
1.2.PC/104 CONNECTOR
(1) 64 Pin PC/104 Connector Bus A & B (PC104)
1
2
64-Pin PC/104 Connector 63
64
(2) 40 Pin PC/104 Connector Bus C & D (PC104)
1
239 40
40 Pin PC/104 Connector
1.3.FDD PORT CONNECTOR (CN2)
1
2
1.4.PARALLEL PORT CONNECTOR
(CN1)
Parallel Port Connector
2
1
13 1
25 14
D-Type Connector
1.5.ETHERNET RJ-45 CONNECTOR
(LAN1) 18
1.6.PS/2 MOUSE CONNECTOR
(CN3&PS1)
KBCLK
VCC
KBDAT
MSDAT
6
5
4
3
2
1
GND
MSCLK
1
2
3
4
5
6
CN3 6 Pin Mini-DIN
PS1
2 MSDAT
1 KBDAT
3 GND
4 VCC
6 MSCLK
5 KBCLK
1.7.PS-ON HEADER (CN4)
3 5VSB
2 VCC
1 PS-ON
CN4
1.8.RESET HEADER (J10)
Shorting these two pins will reset the system.
12
J10
1.9.POWER CONNECTOR (PWR1)
The PWR1 is a 4-pin power connector. It’s the standard
connectors on all Acrosser boards.
2 GND
3 GND
4 +5V
1 +12V
PWR1
1.10.External POWER (J13)
12 1 VCC
2 GND
J13
CAUTION: 1. The detail description manual file was
attached in the software utility CD
2. Suggest to avoid the IDSEL 29 (Before
use the back panel, please check the
IDSEL and slot routing at first.)
PIN (LAN1) FUNCTION
1 TPTX+
2 TPTX-
3 TPRX+
4 Not Used
5 Not Used
6 TPRX-
7 Not Used
8 Not Used
*When AT power supplier is
applied, jumper 2&3 should be
tied together.(Factory preset)
*When ATX power supplier is
applied, pin1&pin 3 should be
connect to proper location of
ATX
p
ower su
pp
lier.

Page2of4 AR-B1543 Manual
1.11.CRT CONNECTOR (DB2)
DB2 (CRT Connector)
6
10
15
11
1
2
3
4
5
1 Red
2 Green
3 Blue
13 Horizontial
14 Vertical Sync
4, 9, & 11 Not used
5 & 10 Ground
6, 7 & 8 AGND
12 DDC DATA
15 DDC CLOCK
1.12.EXTERNAL SPEAKER (J12)
12 1 VCC
2 BEEP
J12
1.13. LCD SUPPORTED VOLTAGE
LCD1Select (JP6)
5 3 1 5 3 1
6 4 2 6 4 2
3.3V(Factory Present) 5V
Lvds1(JP5)
5 3 1
5 3 1
6 4 2 6 4 2
5V 3.3V(FactoryPresent)
1.14. LCD PANEL DISPLAY
CONNECTOR (LCD1)
The pin assignment of LCD connector is shown below:
1
2
Figure 1-1 LCD1: LCD Display Connector
1.15. LED HEADER (J1)
J1
42
531
6
1 HLEDP+
2 HLEDP-
3 HLEDS-
4 HLEDS-
5 P/WLED+
6 P/WLED-
HLEDP : External LED connector for
primary IDE channel.
HLEDS : External LED connector for
secondary IDE channel.
P/WLED: External LED connector for
power status indication.
1.16. USB CONNECTOR (USB1)
USB1
10 8642
97531
1.17.TOUCH SCREEN CONNECTOR
(J7 & J9)
1 RXDF
2 TXDF
3 CGND
Pin Signal Pin Signal
1 GND 2 SHFCLK
3 GND 4 LP
5 FLM 6 GND
7 NC 8 NC
9 P0 (B0) 10 P1 (B1)
11 P2 (B2) 12 P3 (B3)
13 GND 14 DB2 (B4)
15 P5 (B5) 16 NC
17 NC 18 P6 (G0)
19 P7 (G1) 20 GND
21 P8 (G2) 22 P9 ( G3)
23 P10 (G4) 24 P11 (G5)
25 NC 26 NC
27 GND 28 P12 (R0)
29 P13 (R1) 30 P14 (R2)
31 P15 (R3) 32 P16 (R4)
33 P17 (R5) 34 GND
35 VCC 36 VCC
37 +12V 38 +12V
39 GND 40 GND
41 DE 42 ENABLK
43 GND 44 VEE
Pin Description Pin Description
1 USB1V 2 USB2V
3 USBD1F- 4 USBD2F-
5 USBD1F+ 6 USBD2F+
7 GND 8 GND
9 CASE 10 CASE

Page3of4 AR-B1543 Manual
1.18. LVDS HEADER (LVDS1)
1
226
25
1.19. IR. HEADER (J5)
The Infra-red Header pin assignments is as follows:
1 VCC
2 NOT USED
3 IRRX
4 GND
5 IRTX
1.21. EXT. BATTERY (J3)
1 2
1 EXBAT (3.6V)
2 GND
J3
1.22. BATTERY JUMPER (JP3)
1
JP3 1-EXBAT
2-VCC
3-INTVBAT
1.23. COM1, COM2 (DB1, CN5)
DB1(COM1) CN5 (COM2)
9
8
7
6
5
4
3
21
10
9
8
7
6
5
4
3
2
1
DB1 & CN5: RS-232 Connector
1.24. ETHERNET SETUP (JP4)
1) RS-232/RS-485 Select for COM1 (P2 & P3)
The P2&P3 jumpers are designed for selecting the use of
0n-board RS-232 or RS-485 for the DB1 – COM1
P2
P3 P2 P3
A B C A B C
1
2
1
2
1
RS-232
Factory Preset RS-232
2) RS-485 Terminator Select (J6)
When there is only one line the setting should be left off
(please take off the jumper), if multiple blocks are used on a
single line this should be set to “ON”(place a jumper) in order
to properly terminate the connection for better transmission
21 21
OFF ON
Factory Preset
(3) RS-485 Header (J8)
1 2 3
J8 1 N485+
2 N485-
3 GND
1.25. PCI SOLT VOLTAGE (J11)
It must be Jumper, when you need to connect the SOLT.
1
2
3
1
2
3
5V 3.3V
1
2
3
Factory Preset
PIN (LVDS1) FUNCTION
1 TXOUT0-
2 GND
3 TXOUT0+
4 GND
5 TXOUT1-
6 VTX5
7 TXOUT1+
8 VTX5
9 TXOUT2-
10 NC
11 TXOUT2+
12 GND
13 TXCLK-
14 GND
15 TXCLK+
16 VTX12
17 TXOUT3-
18 VTX12
19 TXOUT3+
20 GND
21 VTKBP
22 NC
23 VTX5
24 NC
25 VTX5
26 NC
1-2 2-3
External Battery On-Board Battery
(Factory preset)
DB1 CN5 Signal DB1 CN5 Signal
1 1 /DCD 8 6 /CTS
6 2 /DSR 4 7 /DTR
2 3 RXD 9 8 /RI
7 4 /RTS 5 9 GND
3 5 TXD -- 10 GND

Page4of4 AR-B1543 Manual
1.26. D.O.C. MEMORY BANK
ADDRESS SELECT (JP2)
This section provides the information about how to use the
D.O.C. (Disk On Chip). There divided two parts: hardware
setting and software configuration.
OFFFactory Preset
2
1 2
1ON
Figure 1-2 JP2: D.O.C. Memory Address
1.27.ATX POWER EXTERNAL
BOTTOM CONNECTOR (J4)
OFF
Factory Preset
2
1 2
1ON
1.28. HARD DISK (IDE) CONNECTOR
1) 40-Pin Hard Disk (IDE) Connector (CN6)
A 40-pin header type connector (CN6) is provided to interface
with up to two hard disk drives (IDE AT bus). This interface,
through a 40-pin cable, allows the user to connect up to two
drives in a “daisy chain” fashion. To enable or disable the
hard disk controller, please use the BIOS Setup program,
which is explained further in chapter 5 of operation manual.
The following table illustrates the pin assignments of CN6.
40
39 2
1
2) 44-Pin Hard Disk (IDE) Connector (CN7)
AR-B1543 also provides 44-pin connector IDE interface to
connect with the hard disk device. Furthermore, user could
also apply AR-B9462A (option) to connect with Compact
Flash storage device.
44
43 1
2
Note:
If the content in Setting is inconsistent with CD-ROM.
Please refer to the Setting as priority.
Step 1: Use JP2 to select the correct D.O.C.
memory bank address.
Step 2: Insert programmed Disk On Chip into
sockets U20 setting as DOC.
Step 3: Line up and insert the AR-B1543 card
into slot of your back plane.
JP2 Address Note
ON D000 : 0000 Factory Preset
OFF C800 : 0000
Pin Signal Pin Signal
1 -RESET 2 GROUND
3 DATA 7 4 DATA 8
5 DATA 6 6 DATA 9
7 DATA 5 8 DATA 10
9 DATA 4 10 DATA 11
11 DATA 3 12 DATA 12
13 DATA 2 14 DATA 13
15 DATA 1 16 DATA 14
17 DATA 0 18 DATA 15
19 GROUND 20 NOT USED
21 IDEDREQ 22 GROUND
23 -IOW A 24 GROUND
25 -IOR A 26 GROUND
27 IDEIORDYA 28 GROUND
29 -DACKA 30 GROUND
31 AINT 32 GROUND
33 SA 1 34 Not Used
35 SA 0 36 SA 2
37 CS 0 38 CS 1
39 HD LED A 40 GROUND
41 VCC 42 VCC
43 GROUND 44 Not Used
Pin Signal Pin Signal
1 -RESET 2 GROUND
3 DATA 7 4 DATA 8
5 DATA 6 6 DATA 9
7 DATA 5 8 DATA 10
9 DATA 4 10 DATA 11
11 DATA 3 12 DATA 12
13 DATA 2 14 DATA 13
15 DATA 1 16 DATA 14
17 DATA 0 18 DATA 15
19 GROUND 20 NOT USED
21 IDEDREQ 22 GROUND
23 -IOW A 24 GROUND
25 -IOR A 26 GROUND
27 IDEIORDYA 28 GROUND
29 -DACKA 30 GROUND
31 AINT 32 GROUND
33 SA 1 34 Not Used
35 SA 0 36 SA 2
37 CS 0 38 CS 1
39 HD LED A 40 GROUND