ACTi A952 User manual

A952 ALPR Outdoor Speed Dome Camera Quick Installation Guide
This guide is for quick installing and connecting the camera. For more details, please refer to the User’s Manual.
Installation Notices
•This camera must be installed by qualified personnel and the installation should conform to all local codes.
•Do not replace batteries of the camera. Risk of explosion may occur if the battery is replaced by an incorrect type.
•To use an external power supply, please contact the camera manufacturer to confirm that the power supply
complies with the LPS requirements and shares the same power specifications with the camera.
•For safety concern, please hook up the camera with the anti-drop chain of the
pendant when installing the camera. For more information about pendant and
anti-drop chain, please contact the camera manufacturer.
Camera’s Connectors
No.
Connector
Definition
Remarks
1
RJ-45 Port
For network and IEEE 802.3bt PoE
connections
#Please contact the manufacturer for
compatible PoE injector.
2
Power (AC24V)
AC24V power connection
3
Reset Button
Press the button with a proper tool for at least 20 seconds to restore the system.
4
Audio/Alarm I/O
& RS-485 Connector*
Audio/Alarm I/O
& RS-485 connection
# Do NOT connect external power supply
to the alarm I/O connector of the camera.
5
BNC*
For analog video output
6
SD Card Slot
Insert the SD card into the card slot to store videos and snapshots. Do not remove
the SD card when the camera is powered on.
(*) Optional
NOTE: It is not recommended to record with the SD card for 24/7 continuously, as it may not be able to
support long term continuous data read/write. Please contact the manufacturer of the SD card for information
regarding the reliability and the life expectancy.
Power Connection
To power up the camera, connect the AC24V power adaptor to the power connector of the camera and the power
outlet. Refer to the diagram and pin definition below forAC24V power connection.
Pin
Definition
1
AC24V L
2
GND
3
AC24V N
Alternatively, users can use an Ethernet cable and connect it to the RJ-45 port of the camera and an IEEE 802.3bt
PoE switch.
Ethernet Cable Connection
Connect one end of the Ethernet cable to the RJ-45 connector of the camera, and plug the other end of the cable to
the network switch or PC.
NOTE: In some cases, Ethernet crossover cable might be needed when connecting the camera directly to the
PC.
NOTE: Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit, please check
the LAN connection.
Green Link Light indicates good network connection.
OrangeActivity Light flashes for network activity indication.
NOTE: The camera is to be connected only to PoE networks without routing to the outside plant or equivalent
description.
Audio/AIarm I/O & RS-485 Connection
Please refer to the diagram and pin definition tables below for audio/alarm I/O & RS-485 connection.
Pin
Definition
Pin
Definition
Pin
Definition
Pin
Definition
1
Audio Out
5
Alarm Out B1
9
Alarm In 4
13
GND (Alarm I/O and RS-485)
2
GND (Audio I/O)
6
Alarm Out B2
10
Alarm In 3
14
Audio In
3
Alarm Out A1
7
RS-485 D+ (Optional)
11
Alarm In 2
4
Alarm Out A2
8
RS-485 D- (Optional)
12
Alarm In 1

V20230817
Before Login to the Camera
A client program will be automatically installed to the PC when connecting to the camera. Before logging in to the
camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and
plug-ins or setting Internet’s security level to default. For further details, please refer to the User’s Manual.
ActiveX Controls and Plug-ins Settings
Internet Security Level
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
<Internet>, and click on <Custom level> to
change ActiveX settings.
Step 4: Set “ActiveX controls and plug-ins”items to
<Prompt> or <Enable>.
Step 1: Start the IE Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
<Internet>.
Step 4: Down the page, click on <Default Level> and
<OK> to confirm the setting. Close the browser
window, and open a new one later for
accessing the IP camera.
NOTE: It is strongly recommended using Microsoft Internet Explorer 10.0 or later version to connect the
camera.
Camera Login
The default IP address of the camera is: 192.168.0.100. Therefore, to access the camera for the first time, please set
the IP address of the PC as: 192.168.0.XXX; for example:
IP Address: 192.168.0.99
Subnet Mask: 255.255.255.0
Login ID & Password
•Type in corresponding camera IP address into the URL field on the web browser and hit “Enter”.
•For initial login, use the default username (admin) and then set up the password. Follow the on-screen instructions
to do so. This username and password will be used for succeeding login. Note that the username and password
are case sensitive.
Default Username: admin
Password: (user must set up first)
Install the ActiveX Control
•After connecting to the camera, the request for installing the ActiveX control will appear just below the URL bar.
Follow the on-screen instructions to complete installation.
Browser-based Viewer
The main page of the IP camera user interface is as shown below.
A952
8MP ALPR
Outdoor Speed Dome
Quick Guide