ActionTec GT701-WG User manual

Solutions for the Digital Life™
User Manual
54 Mbps
Wireless
DSL Gateway
Model #: GT701WG
Firmware version: 3.0.1.0.5-GT701-WG
IB: 2.12.04.230

i
Table of Contents
1 Introduction 1
Package Contents 1
Minimum System Requirements 2
Features 2
Getting to Know the Gateway 4
2 Setting Up the Gateway 7
Connecting a Computer to the Gateway 7
Installing Phone Filters 22
Setting Up the DSL Connection 28
3 Performing a Basic Setup 33
Basic Setup 33
Changing the Admin User Name and Password 36
4 Using Advanced Setup 37
Accessing Advanced Setup 37
WAN IP Address 39
Wireless Settings 44
Wireless MAC Authentication 47
Wireless Advanced Settings 48
LAN IP Address 49
DHCP Server 49
Services Blocking 51
Website Blocking 52
Remote Management 53
Port Forwarding 54
DMZ Hosting 55
Firewall 56
Dynamic Routing 56
NAT (Network Address Translation) 57
Static Routing 57
UPnP (Universal Plug and Play) 58
5 Viewing the Gateway’s Settings 59
Status 59
Routing Table 61
WAN Status 61
LAN Status 62
Active User List 62
6 Using Utilities 63
Web Activity Log 63
DSL Settings 64
Restore Default Settings 64
Upgrade Firmware 65

ii
Actiontec 54 Mbps Wireless DSL Gateway User Manual
ii
7 Setting Up a Network 67
Ethernet 67
USB 72
Wireless 77
8 Troubleshooting 81
Troubleshooting 81
Frequently Asked Questions 82
A Reference 87
Locating Computer Information 87
Locating Windows Operating System Files 88
B Setting Up Static IP on the Computer 91
Windows 98 SE 91
Windows Me 94
Windows 2000 97
Windows XP 101
C Computer Security 107
Comparing DSL Service with a Dial-Up Modem 107
Gateway Security 108
Computer Security 108
Electronic Security 109
D Specifications 111
General 111
Wireless Operating Range 112
LED Indicators 112
Environmental 112
E Glossary 113
F Firewall Security Level Services Table 117
High Security Level 117
Medium Security Level 118
Low Security Level 118
Basic Security Level 119
Service Acronym Definitions 119
G Non-Windows System Setup 121
Classic 121
OS X 123
H Installation Buddy Settings 125
Notices 127
Regulatory Compliance Notices 127
Modifications 127
Miscellaneous Legal Notices 128
Limited Warranty 129

1
Introduction
Thank you for purchasing the Actiontec 54 Mbps Wireless DSL Gateway. The
Gateway is the simplest way to connect computers to a high-speed broadband
connection. This easy-to-use product is perfect for the home office or small busi-
ness. If you want to take your computing to the next level, the Actiontec 54 Mbps
Wireless DSL Gateway is sure to be one of the keys to your success.
Package Contents
s Actiontec 54 Mbps Wireless DSL Gateway
s Black bag (includes Power cord and green DSL cable)
s Phone filters
s Yellow (Ethernet) cable
s Purple (USB) cable
s Installation CD
s Quick start guide
1

2
Actiontec 54 Mbps Wireless DSL Gateway User Manual
3
Chapter 1 Introduction
Minimum System Requirements
s Active DSL service
s Computer with a 10/100 Mbps Ethernet connection, or USB connection
s Microsoft Windows 98 Second Edition (SE), Windows Millennium Edition
(Me), Windows NT 4.0, Windows 2000, Windows XP, Mac OS 7.1 and above
☞ Note: USB LAN port is not supported with Microsoft Windows
95, Windows NT 4.0, or any Mac OS.
s Internet Explorer 4.0 or higher (5.x recommended) or Netscape Navigator
4.0 or higher (4.7 recommended)
s TCP/IP network protocol installed on each computer
Features
s Plug-and-Play installation support for systems with Windows operating
systems (98, 98SE, Me, 2000, and XP)
s ADSL WAN port (RJ-11)
s Compliant with full-rate ANSI T1.413 Issue 2, ITU G.992.1 (G.dmt) and
G.992.2 (G.lite) standard
s Auto-handshake for different ADSL flavors
s USB 1.1 device specification compliance
s 11 Mbps USB data rate (full speed)
s Bridged Ethernet over ATM, PPP over ATM, PPP over Ethernet
s Precise ATM traffic shaping
s IP packet routing and transparent bridge
s Routing protocol supports RIP-1, RIP-2, static routing
s Built-in NAT, DHCP server

2
Actiontec 54 Mbps Wireless DSL Gateway User Manual
3
Chapter 1 Introduction
s DNS relay support
s PAP/CHAP authentication, administrative passwords through Telnet
s 64-, 128-, and 256-bit WEP/WPA wireless LAN security
s Compliant with IEEE 802.3 Ethernet standard
s 10/100 Base-T Ethernet port
s Flow control support for Fast Ethernet
s Web-based configuration setup
s Default configuration backup restore
s FTP firmware upgradeable
s Web download support
s 802.11b/g support

4
Actiontec 54 Mbps Wireless DSL Gateway User Manual
5
Chapter 1 Introduction
Getting to Know the Gateway
This section contains a quick description of the Gateway’s lights, ports, etc.
The Gateway contains several indicator lights (LEDs) on its front panel and a series
of ports on its rear panel.
Front Panel
The front panel of the Gateway features six lights: Power, DSL, Internet,
Ethernet, USB, and Wireless.
Power
DSL
Internet
Ethernet USB
Wireless
Power
DSL InternetEthernet Wireless
USB
Power Light
The Power light displays the Gateway’s current status. If the Power light glows
steadily green, the Gateway is receiving power and fully operational. When the
Power light flashes rapidly, the Gateway is initializing. If the Power light is not
illuminated when the Power cord is plugged in, the Gateway has suffered a criti-
cal error and technical support should be contacted.
DSL Light
The DSL light illuminates when the Gateway is connected to a DSL line.

4
Actiontec 54 Mbps Wireless DSL Gateway User Manual
5
Chapter 1 Introduction
Internet Light
When the Internet light glows steadily, the Gateway is connected to the DSL
provider. When it flashes, the Gateway’s built-in DSL modem is training for
DSL service.
Ethernet Light
The Ethernet light illuminates when the Gateway is connected via its
Ethernet port.
USB Light
The USB light illuminates when the Gateway is connected via its USB port.
Wireless Light
The Wireless light illuminates when the Gateway is connected wirelessly.
Rear Panel
The rear panel of the Gateway contains five ports (Line, Phone, USB, Ethernet, and
Power), as well as a Reset switch.
Power
Reset
Phone
LineUSB
Ethernet
Line Port
The Line port is used to connect the Gateway to a DSL (Digital Subscriber Line)
connection.

6
Actiontec 54 Mbps Wireless DSL Gateway User Manual
Phone Port
The Phone port is used to connect the Gateway to a telephone.
USB Port
The USB port is used to connect a computer to the Gateway via USB cable.
Ethernet Port
The Ethernet port is used to connect a computer to the Gateway via Ethernet
cable. The Ethernet port is a 10/100 Mbps auto-sensing port, and either a
straight-through or crossover Ethernet cable can be used when connecting to
the port.
Reset Switch
Depressing the Reset switch for one or two seconds will power cycle the Gateway
(similar to unplugging and then plugging in the Gateway’s Power cord). To
restore the Gateway’s factory default settings, depress and hold the Reset switch
for approximately 10 seconds. The reset process will start about 10 seconds after
releasing the switch.
Power Port
The Power port is used to connect the Power cord to the Gateway.
N Warning: Do not unplug the Power cord from the Gateway’s
Power port during the reset process. Doing so may result in per-
manent damage to the Gateway.

7
Setting Up
the Gateway
The instructions that follow parallel the steps contained in the Actiontec Installation
Buddy®, which provides a visual guide to setting up the Gateway. It is recommended
the user run the Installation Buddy first, before attempting any other procedures.
To set up the Gateway, it must be connected to a computer, and then configured.
After connecting this first computer, other computers can be added to the network
via USB, Ethernet, or wirelessly (see “Setting Up a Network” on page 67).
Connecting a Computer to the Gateway
Connecting a computer to the Gateway for setup involves three basic steps: initial
setup, plugging in the Gateway’s power cord, and connecting the Gateway to the
computer.
Connecting Via Ethernet
1. Insert the Installation CD in the CD-ROM drive of the computer. The
Installation Buddy starts automatically. Wait until the following screen
appears, read the on-screen instructions, select the country in which you live
by clicking in the appropriate check box, then click Next.
2

8
Actiontec 54 Mbps Wireless DSL Gateway User Manual
9
Chapter 2 Setting Up the Gateway
2. Read the instructions, select Initial Setup by clicking on the appropriate check
box, then click Next.
3. If USA was chosen in step 1, select the appropriate letter (as designated by the
ISP) from the options in the next window, then click Next.
If United Kingdom or Other Country was selected, go directly to step 4.

8
Actiontec 54 Mbps Wireless DSL Gateway User Manual
9
Chapter 2 Setting Up the Gateway
4. Click in the check box next to Ethernet (Recommended), then click Next.
5. Make sure the items needed to connect the Gateway to the first computer are
included in the kit, then click Next.

10
Actiontec 54 Mbps Wireless DSL Gateway User Manual
11
Chapter 2 Setting Up the Gateway
6. Get the Gateway from the kit, then click Next.
7. Get the Power cord from the Black Bag and plug the smaller end into the
black Power port on the rear panel of the Gateway, then click Next.

10
Actiontec 54 Mbps Wireless DSL Gateway User Manual
11
Chapter 2 Setting Up the Gateway
8. Plug the larger end of the Power cord into a power outlet, then click Next.
9. Confirm the Power light on the front of the Gateway glows solid green, then
click Next.

12
Actiontec 54 Mbps Wireless DSL Gateway User Manual
13
Chapter 2 Setting Up the Gateway
10. Get the yellow Ethernet cable from the kit and plug one end into the yellow
Ethernet port on the back of the Gateway, then click Next.
11. Plug the other end of the yellow Ethernet cable into an Ethernet port on
the back of the computer. Click Next.
☞ Note: An Ethernet port looks similar to a phone jack, but is
slightly larger.

12
Actiontec 54 Mbps Wireless DSL Gateway User Manual
13
Chapter 2 Setting Up the Gateway
12. Make sure the Ethernet light on the front of the Gateway glows solid green.
Click Next.
13. Get the green DSL cable from the Black Bag and plug one end into the green
Line port on the rear panel of the Gateway. Click Next.

14
Actiontec 54 Mbps Wireless DSL Gateway User Manual
15
Chapter 2 Setting Up the Gateway
14. Plug the other end of the green DSL cable into the phone jack closest to the
computer. Click Next.
15. Make sure the the DSL light on the Gateway glows solid green (it may take a
few moments). Click Next.
The Gateway is connected to a computer via Ethernet. Next, install the filters as
described in “Installing Filters” on page 22.

14
Actiontec 54 Mbps Wireless DSL Gateway User Manual
15
Chapter 2 Setting Up the Gateway
Connecting Via USB
1. Insert the Installation CD in the CD-ROM drive of the computer. The
Installation Buddy starts automatically. Wait until the following screen
appears, read the on-screen instructions, select the country in which you live
by clicking in the appropriate check box, then click Next.
2. Read the instructions, select Initial Setup by clicking on the appropriate check
box, then click Next.

16
Actiontec 54 Mbps Wireless DSL Gateway User Manual
17
Chapter 2 Setting Up the Gateway
3. If USA was chosen in step 1, select the appropriate letter (as designated by the
ISP) from the options in the next window, then click Next.
If United Kingdom or Other Country was selected, go directly to step 4.
4. Click in the check box next to USB, then click Next.

16
Actiontec 54 Mbps Wireless DSL Gateway User Manual
17
Chapter 2 Setting Up the Gateway
5. Make sure the items needed to connect the Gateway to the first computer are
included in the kit, then click Next.
6. Get the Gateway from the kit, then click Next.