Actonis DUAL ACTION 18 User manual

DUAL ACTION 18
LaserComb
USER MANUAL
LUH018DWEDXXX-00-0723.indd 1LUH018DWEDXXX-00-0723.indd 1 7/18/23 1:53 PM7/18/23 1:53 PM

INTRODUCTION | WHO IS THE BEST CANDIDATE
1
ENGLISH
INTRODUCTION
Introduction to ActonisTM
The Actonis Dual Action 18 LaserComb is a home-use laser device that has been
clinically proven to treat early to moderate stages of hereditary/hormonal hair
loss.
Indication
Actonis models are indicated to treat Androgenetic Alopecia, and promote hair
growth in females who have Ludwig (Savin) I-4, II-1, II-2, or frontal patterns of
hair loss with Fitzpatrick Skin Types I to IV.
How Actonis works
Actonis works by providing therapeutic laser energy to stimulate hair follicles.
Your device should be used 3 times per week, spaced out every other day. For
example, Monday, Wednesday, Friday. The device should not be used more than
the recommended treatment time per day. Clinical studies demonstrate that
most users see benets in as little as 16 weeks.
Actonis Results
Actonis laser therapy has been proven in clinical studies. In these clinical studies,
over 97% of the women experienced signicant hair growth, on average, 21 new
hairs per square centimeter/133 per square inch.
It is important that you read and understand the content of this user manual
before using your device.
WHO IS THE BEST CANDIDATE FOR Actonis?
How do you know if the Actonis LaserComb is right for you?
Your device can be used by women with thinning hair (including color treated
hair) or pattern baldness caused by a hereditary/hormonal condition. Doctors
use a system known as the Ludwig-Savin Classication (women) to describe the
degree of hair loss. Below are the pictures of the scales. The shaded areas show
the type of hair loss that can be treated with your device.
CLASSIFICATION FOR WOMEN
Ludwig-Savin Classication - Females
LUH018DWEDXXX-00-0723.indd 2LUH018DWEDXXX-00-0723.indd 2 7/18/23 1:53 PM7/18/23 1:53 PM

2
SYMBOLS
European Conformity
WEEE
Warning
Caution
Laser
Laser warning
Laser aperture indication
Laser warning label
Power On/Off
Refer to instruction manual
RF interference
Type BF Applied Part
Serial Number
Degree of moisture resistance
Low-level ESD
Manufacturer
TESTING FOR SENSITIVITY
Prior to treatment, test your skin for sensitivity by shining the light on the inside
of your forearm for 2 minutes. If you see any reaction, do not use your device and
contact customer service.
HOW TO MONITOR DEVICE ACTIVITY
Your device is manufactured in an ISO 13485 certied facility using the highest
quality components. Your device should provide many years of trouble-free
usage. When working properly, a therapeutic red laser light should shine out of
the device. The laser light does not diminish over time.
PARTS
WHAT IS INCLUDED
1. Actonis 18 LaserComb 3. Power supply with cord
2. Charging cradle 4. Quick Start Guide
Notice: Entire Actonis assembly is considered as a Type BF applied part.
This is a harmless low-level ESD (Electrostatic Discharge) sensitive device.Please do not touch the charging contacts or USB-port.Touching
the contacts or USB-port is not of the essential performance and will not cause a basic safety issue. If touching the contacts or USB-port causes the
device to malfunction, reset your device by powering off and back on.
SYMBOLS | TESTING FOR SENSITIVITY | HOW TO MONITOR DEVICE ACTIVITY | PARTS | WHAT IS INCLUDED
CHARGING
CRADLE/STAND
LASER
BUTTON
POWER BUTTON/
INDICATOR LIGHT
USB-C
JACK
USB-C JACK
POWER SUPPLY WITH CORD
LUH018DWEDXXX-00-0723.indd 3LUH018DWEDXXX-00-0723.indd 3 7/18/23 1:53 PM7/18/23 1:53 PM

GETTING STARTED | CHARGING OPTIONS
3
GETTING STARTED
Your Actonis device comes with a rechargeable battery permanently installed. Read
this manual completely before you start to use your Actonis. The instructions in
this user manual are intended for individuals with a minimum of an eighth grade
education. Actonis is safe for home use. The consumer is the intended operator of
this equipment.
Use the Actonis Dual Acton 18 LaserComb for
8 minutes per treatment, three treatments per
week. The treatments should be spaced every
other day, for example Monday, Wednesday,
Friday. Do not use your Actonis more than the
recommended treatment time per day. Most
users see benets in as little as 16 weeks (based
on clinical studies).
When you receive your device, take all the parts out of the case. You must charge
your Actonis for 2-3 hours before initial use.
CHARGING OPTIONS
OPTION 1: Charge your device using the charging cradle
and power cord (Figure A). Prior to placing your device
in the cradle, make sure it is turned off and the teeth face
away from you. Plug the power cord into the cradle and
the other end into an electrical wall outlet. A green light
will illuminate on the back of the charging stand indicating
that your power cord is operating properly.
OPTION 2: Charge your device by placing the power
cord directly into the device and the other end into an
electrical wall outlet (Figure B).
The indicator light on the power button will ash during
the charging process. Once charging is complete, the
light will stop ashing and remain on.
When the battery is fully charged, the indicator light
will be on. As the battery power diminishes, the light
will blink slowly. When the battery is getting low and
needs to be recharged, the light will start to ash rapidly.
When this happens, charge your device with one of the
charging options as previously described.
During use, the indicator light will indicate the battery
level. A steady, non-ashing light indicates the battery is
full (Figure C).
If your device needs to be recharged during your
treatment, allow it to fully charge before continuing.
MINUTES MINUTES
Ultima 9 Ultima 12
minutes
83 times
per week
POWER BUTTON
LASER BUTTON
POWER BUTTON
LASER BUTTON
POWER BUTTON
LASER BUTTON
A
B
C
LUH018DWEDXXX-00-0723.indd 4LUH018DWEDXXX-00-0723.indd 4 7/18/23 1:53 PM7/18/23 1:53 PM

PROPER USE | TREATMENT METHOD
4
PROPER USE
The Actonis Dual Action 18 LaserComb should be used for 8 minutes.
Use a watch or clock to time your treatment.
First, press the power button until power button light turns on.
Second, press the laser button. Your device is ready for use.
Shine your device onto the palm of your hand and you will see
that the laser light is on (do not look at the laser light directly).
Do not use your device if the device is damaged or defective,
contact Actonis customer service or your place of purchase.
TREATMENT METHOD
Prior to treatment, test your skin for sensitivity. See prior TESTING FOR
SENSITIVITY section.
After you have turned on your device, place it at
on your scalp so that both rows of the teeth are
touching your scalp (Figure D).
Start at your hairline. Move your device from front
to back of scalp in a slow combing motion, pausing
every 1/2 inch (1 cm) for 4 seconds (Figure E).
When your device is on, it will beep and vibrate
every four (4) seconds. This means that it’s time to
move your device to the next area of the scalp. Do
not lift your device off your scalp while combing
from front to back.
Continue in this manner from front to back and then
side to side until you cover your entire scalp with
multiple passes (Figure E).
Repeat these passes for the total treatment of 8
minutes.
If you have long hair, use your ngers to lift your
hair out of the way while using your device to be
sure that the laser energy reaches your scalp.
NOTE: The Actonis Dual Action 18 LaserComb will
turn off automatically after 8 minutes.
If your device needs to be recharged during your treatment, allow the device
to fully charge before continuing your treatment. Do not turn on or use your
device while it is charging.
POWER BUTTON
LASER BUTTON
POWER BUTTON
LASER BUTTON
POWER BUTTON
LASER BUTTON
POWER BUTTON
LASER BUTTON
POWER BUTTON
LASER BUTTON
D
E
F
LUH018DWEDXXX-00-0723.indd 5LUH018DWEDXXX-00-0723.indd 5 7/18/23 1:53 PM7/18/23 1:53 PM

TREATMENT METHOD | TROUBLESHOOTING
5
IMPORTANT: Do not lift your device off your head when moving from front to
back. Your device features a pair of comb teeth that part the hair so the light can
more effectively reach the scalp. You will make a few complete passes over your
scalp within the recommended treatment time.
If you wish to turn off the beep/vibration during the
treatment, press the top laser button once (Figure G).
Your device and laser will remain on. To re-activate beep
and vibration, simply press the laser button twice.
Turn off your device by pressing and holding the power
button (lower button) until indicator light turns off
(Figure H). Store the device in the charging cradle for
future use. You may leave the power cord plugged into
the charging cradle at all times.
Please Note:
It is important to move your device very
slowly. Remember, you are bathing the scalp
with laser light. If you move it too fast, the
treatment will not achieve the optimal results
to promote hair growth.
TROUBLESHOOTING
ANY ATTEMPT TO SELF-SERVICE YOUR DEVICE, UNLESS INSTRUCTED BY ACTONIS
CUSTOMER SERVICE, WILL VOID YOUR WARRANTY.
Actonis has advanced electronics to ensure that the device is working like it is
supposed to and that the proper amount of laser energy is being delivered. If for
some reason you are experiencing difculties with your device, please try one of the
tips below:
If your device will not turn on
• Make sure your device is fully charged.
• Press the power button for 4 seconds and then the laser button.
• Try another electrical wall outlet.
If your device is turning off during use
• Make sure your device is fully charged.
• Press the power button for 4 seconds and then the laser button.
• Try another electrical wall outlet.
If your device will not turn off
• Press and hold the power button for 4 seconds.
If your device beeps/vibrates irregularly or doesn’t beep/vibrate at all
• Press the power button then the laser button.
If your device beeps and vibrates, but you do not see the laser light
• Press the power button then the laser button.
POWER BUTTON
LASER BUTTON
POWER BUTTON
LASER BUTTON
G
H
LUH018DWEDXXX-00-0723.indd 6LUH018DWEDXXX-00-0723.indd 6 7/18/23 1:53 PM7/18/23 1:53 PM

LASER PARAMETERS | USE CONDITIONS | WARNING LABEL | POWER SUPPLY SPECIFICATIONS
6
POWER SUPPLY SPECIFICATIONS
The power supply for your Actonis can be used in the United States and
Internationally. This power supply will adapt to all power supplies from 100
volt/60 Hz (US) to 240 volt/50 Hz. If outlets in your country have different plugs
than the power supply that comes with the Actonis, use an inexpensive plug
adapter not supplied with the device.
LASER PARAMETERS
Wavelength: 655nm and 635nm visible red light
Laser Power for classication: <5mW
Divergence: 57 mrad
Number of lasers: 9 (655nm) 9 (635nm)
This Laser Product is designated as Class 3R during all procedures of operation.
Note: Actonis laser devices have no user-serviceable parts.
USE CONDITIONS
MTBF Lasers (mean time between failures): 10,000 hours at 25ºC ambient
temperature
Operating temperature/altitude/atmospheric pressure/humidity: 5ºC to 35ºC/0
to 2,000 m/80kPa to 106kPa/0% to 90%, relative humidity
Storage & transportation temperature/humidity/atmospheric pressure: -20ºC to
60º C/0% to 90%, relative humidity/50kPa to 106kPa
Ingress of water or particulate matter: IP22
Battery charging cycles: 300 cycles
ROHS (restriction of hazardous substances): 2011/65/EU
Device size and weight: 9.5 x 2.5 x 2 in (24.3 x 6 x 5 cm) / 6.4 oz (181 gm)
Cradle size and weight: 5.5 x 4.375 x 2.75 in (14 x 11 x 7 cm) / 7.0 oz (198 gm)
Product warranty: 2 years
Age of use: Adult
Software Version: KM910DW-V19-20230613A-120hz
WARNING LABEL
Warning label Serial number
APERTURELASER
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
CLASS 3R PER IEC 60825-1:2014
655nm <5mW CW 5V 1.0A
635nm <5mW PW 5V 1.0A
Complies with FDA performance standards
per Laser Notice No. 50, dated June 24, 2007
Patent www.actonis.com/patents
Made in Taiwan for
Lexington International LLC
1040 Holland Drive
Boca Raton FL 33487 USA
MODEL: H018DA
(01) 00856823006305
(11) 220714
(21) H018DA000001
S/N: H018DA000001
LUH018DWEDXXX-00-0723.indd 7LUH018DWEDXXX-00-0723.indd 7 7/18/23 1:53 PM7/18/23 1:53 PM

WARNING | CAUTIONS
7
Do not stare directly at the red laser light or its reection in a mirror because
it can temporarily irritate your eyes. If you stare at the light for too long, it
could harm your eyes. Also, never use a magnifying glass when using your
device because it can cause temporary irritation to your eyes.
Keep the device out of the reach of children and pets.
Do not drop your device in water because you may get an electrical shock. If
your device gets damaged by water, contact customer service.
If the cord is damaged on your device do not use the device because you
could get an electrical shock. If the cord gets damaged, contact customer
service.
Do not use your device near any heated surfaces because this could cause
the device not to work properly and may cause an electrical shock, contact
customer service.
Laser light - avoid direct eye exposure.
This is a harmless low-level ESD (Electrostatic Discharge) sensitive device.
Please do not touch the USB port. Touching the contacts or USB port is
not of the essential performance and will not cause a basic safety issue. If
touching the contacts or USB port causes the device to malfunction, reset
your device by powering off and back on.
No modication of this equipment is allowed.
This equipment has no user-serviceable parts. Do not attempt to modify or
repair this equipment.
Do not attempt to modify or service while the equipment is in use.
If this equipment is modied, appropriate inspection and testing must be
conducted to ensure continued safe use. Contact Actonis customer service.
WARNINGS
CAUTIONS
If you are taking any medications or products that make you sensitive to
light, you should test your device to make sure you do not have a reaction.
Some of the things that can cause increased sensitivity to your device could
be medicines for colds, allergies, pain medicine and drugs to treat infections.
To test your device for sensitivity, turn the device on, hold the device on one
spot, shining the light on your forearm. After two minutes, turn the device off
and set aside. Look at the spot where you held the laser light over the next
ve minutes. If you see any reaction such as redness or rash, do not use your
device and contact our customer service information on how to return to
place of purchase and get a refund.
Only use your device as directed. Do not try to change the way your device
operates. Altering controls, adjustments, performance or procedures
other than those specied herein may result in hazardous radiation (laser)
exposure. Contact customer service.
Never use acetone or other solvents on any part of your device. Use of
solvents on the window can block the laser light from coming through.
LUH018DWEDXXX-00-0723.indd 8LUH018DWEDXXX-00-0723.indd 8 7/18/23 1:53 PM7/18/23 1:53 PM

MAINTENANCE | CLEANING YOUR Actonis | DISPOSAL INSTRUCTIONS | ELECTRICAL SAFETY
8
MAINTENANCE
Actonis is designed to last for many years. It does not require any maintenance
other than periodic cleaning.
Your device is intended for indoor use only.
CLEANING YOUR ACTONIS
• Keep your device clean.
• Turn off the device by pressing and holding the power button (lower button)
until the light turns off.
• Unplug the power cord from the device and from the electrical wall outlet.
• To clean the teeth more thoroughly, slide the teeth towards the top of your
device and gently pull out. Clean with soap and water.
• Clean the laser window with a soft, slightly moistened cloth. Don’t use any
acetone or solvents.
DISPOSAL INSTRUCTIONS
This symbol on the product or on its packaging indicates that
this product must not be disposed of with your other household
waste. Instead, it is your responsibility to dispose of your waste
equipment by handing it over to a designated collection point
for the recycling of waste electrical and electronic equipment.
The separate collection and recycling of your waste equipment
at the time of disposal will help to conserve natural resources
and ensure that it is recycled in a manner that protects human
health and the environment. For more information about where you can drop off
your waste equipment for recycling, please contact your local city ofce or your
household waste disposal service.
ELECTRICAL SAFETY
Basic safety precautions should be observed when using this, or any other
electrical device, especially when children are present.
To reduce the risk of hazard by electric shock:
WARNING: Keep away from water. Contact with water may result in an
electrical shock.
Do not use while bathing.
Do not place or store your Actonis where it can fall or be pulled into a tub or
sink.
Do not expose your Actonis to running water, or drop into water or any other
liquid. If your Actonis falls into water, unplug it immediately from the power
outlet.
If using your Actonis near water, the use of an electrical outlet protected by a
Ground Fault Circuit Interrupter is recommended.
Do not dispose of your Actonis in a re or store in high temperatures greater
than 140°F (60°C).
Do not turn on or use your Actonis while it is charging.
Power supply cannot be separated during use. Do not position the
equipment in a manner that will make it difcult to plug in or remove the
power cord.
If you have any problems with this device, such as setting up, maintaining or
using, please contact customer service.
Please report to customer service if any unexpected operation or events
occur.
LUH018DWEDXXX-00-0723.indd 9LUH018DWEDXXX-00-0723.indd 9 7/18/23 1:53 PM7/18/23 1:53 PM

ELECTRICAL SAFETY | ELECTROMAGNETIC EMISSIONS GUIDANCE
9
After drop/shock, that may cause changes in the performance, please
contact customer service.
Be careful, do not put the power cord around your neck, it may cause
strangulation.
Keep the device out of the reach of children/pets to avoid inhalation or
swallowing of small parts.
Do not use the device if it is damaged in any way. The continuous use of a
damaged unit may cause injury, improper results, or serious danger.
The device should be used only with the accessories recommended for use
by the manufacturer.
When not in use, store the device with the adapter in a dry room and protect
it against extreme moisture, heat, lint, dust and direct sunlight. Never place
any heavy objects on the storage case.
ELECTROMAGNETIC EMISSIONS GUIDANCE
Guidance and manufacturer’s declaration – electromagnetic emissions
The LaserComb intended for use in the electromagnetic environment specied
below. The customer or the user of the LaserComb should assure that it is used
in such an environment.
Emission test Compliance Electromagnetic
environment-guidance
RF emissions CISPR 11 Group 1 The LaserComb use RF energy only for its
internal function. Therefore, its RF emissions
are very low and are not likely to cause any
interference in nearby electronic equipment.
RF emissions CISPR 11 Class B The LaserComb is suitable for use in
all establishments, including domestic
establishments and those directly
connected to the public low-voltage power
supply network that supplies buildings used
for domestic purposes.
Harmonic emissions IEC 61000-3-2 Class A
Voltage uctuations/icker emissions
IEC 61000-3-3
Compliance
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) the device
must accept any interference received, including interference that may cause undesired
operation.
LUH018DWEDXXX-00-0723.indd 10LUH018DWEDXXX-00-0723.indd 10 7/18/23 1:53 PM7/18/23 1:53 PM

10
ELECTROMAGNETIC IMMUNITY GUIDANCE
ELECTROMAGNETIC IMMUNITY GUIDANCE
Guidance and manufacturer’s declaration – electromagnetic immunity
The LaserComb is intended for use in the electromagnetic environment specied
below. The customer or the user of the LaserComb should assure that it is used in
such an environment.
Immunity test IEC 60601 test level Compliance level Electromagnetic
environment-
guidance
Electrostatic
discharge (ESD)
IEC 61000-4-2
± 6 kV contact
± 8 kV air
± 6 kV contact
± 8 kV air
Floors should be
wood, concrete or
ceramic tile. If oors
are covered with
synthetic material,
the relative humidity
should be at least
30%.
Electrical fast
transient/burst
IEC 61000-4-4
± 2kV for power supply lines
± 1kV for input/output lines
± 2kV for power supply
lines
Non applicable
Mains power quality
should be that of a
typical commercial or
hospital environment.
Surge
IEC 61000-4-5
± 1kV line(s) to line(s)
± 2kV line(s) to earth
± 1kV differential mode
Non applicable
Mains power quality
should be that of a
typical commercial or
hospital environment.
Voltage
dips, short
interruptions and
voltage variations
on power supply
input lines
IEC 61000-4-11
<5% UT (>95% dip in UT)
for 0.5 cycle
40% UT (60% dip in UT)
for 5 cycles
70% UT (30% dip in UT)
for 25 cycles
<5% UT (>95% dip in UT)
for 5 sec
<5% UT (>95% dip in UT)
for 0.5 cycle
40% UT (60% dip in UT)
for 5 cycles
70% UT (30% dip in UT)
for 25 cycles
<5% UT (>95% dip in UT)
for 5 sec
Mains power quality
should be that of a
typical commercial or
hospital environment.
If the user of the
LaserComb require
continued operation
during power mains
interruptions, it is
recommended that
the LaserComb be
powered from an
uninterruptible power
supply or a battery.
Power frequency
(50Hz/60Hz)
magnetic eld
IEC 61000-4-8
3 A/m 3 A/m The LaserComb power
frequency magnetic
elds should be at
levels characteristic of
a typical location in a
typical commercial or
hospital environment.
NOTE UT is the a.c. mains voltage prior to application of the test level.
LUH018DWEDXXX-00-0723.indd 11LUH018DWEDXXX-00-0723.indd 11 7/18/23 1:53 PM7/18/23 1:53 PM

ELECTROMAGNETIC IMMUNITY GUIDANCE
11
ELECTROMAGNETIC IMMUNITY GUIDANCE
Guidance and manufacturer’s declaration – electromagnetic immunity
The LaserComb is intended for use in the electromagnetic environment specied
below. The customer or the user of the LaserComb should assure that it is used
in such an environment.
Immunity test IEC 60601
test level
Compliance
level
Electromagnetic environment-guidance
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
3 Vrms
150 kHz to 80 MHz
3 V/m
80 MHz to 2.5 GHz
3 Vrms
3 V/m
Portable and mobile RF communications
equipment should be used no closer to any
part of the LaserComb including cables,
than the recommended separation distance
calculated from the equation applicable to the
frequency of the transmitter.
Recommended separation distance:
d = 1,2 √P
d = 1,2 √P 80 MHz to 800 MHz
d = 2,3 √P 800 MHz to 2,5 GHz
Where P is the maximum output power rating
of the transmitter in watts (W) according to
the transmitter manufacturer and d is the
recommended separation distance in metres
(m).
Field strengths from xed RF transmitters, as
determined by an electromagnetic site survey,a
should be less than the compliance level in
each frequency range.b
Interference may occur in the
vicinity of equipment marked
with the following symbol:
NOTE1 At 80 MHz and 800 MHz, the higher frequency range applies.
NOTE2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reection from structures, objects and people.
!
!
Field strengths from xed transmitters, such as base stations for radio (cellular/cordless)
telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV
broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to xed RF transmitters, an electromagnetic site survey should be
considered. If the measured eld strength in the location in which the LaserComb is used exceeds
the applicable RF compliance level above, the LaserComb should be observed to verify normal
operation. If abnormal performance is observed, additional measures may be necessary, such as
re-orienting or relocating the LaserComb.
Over the frequency range 150 kHz to 80 MHz, eld strengths should be less than 3 V/m.
a
b
LUH018DWEDXXX-00-0723.indd 12LUH018DWEDXXX-00-0723.indd 12 7/18/23 1:53 PM7/18/23 1:53 PM

ELECTROMAGNETIC DISTANCE RECOMMENDATIONS
12
ELECTROMAGNETIC DISTANCE RECOMMENDATIONS
Recommended separation distance between portable and mobile RF
communications equipment and the LaserComb.
The LaserComb is intended for use in an electromagnetic environment in
which radiated RF disturbances are controlled. The customer or the user of the
LaserComb can help prevent electromagnetic interference by maintaining a
minimum distance between portable and mobile RF communications equipment
(transmitters) and the LaserComb as recommended below, according to the
maximum output power of the communications equipment.
Rated maximum
output
power of transmitter
(W)
Separation distance according to frequency of transmitter
(m)
150 kHz to 80 MHz
d =1,2√P
80 MHz to 800 MHz
d =1,2√P
800 MHz to 2.5 GHz
d =2,3√P
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3.8 3.8 7.3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation
distance d in metres (m) can be estimated using the equation applicable to the frequency of the
transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the
transmitter manufacturer.
NOTE1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reection from structures, objects and people.
LUH018DWEDXXX-00-0723.indd 13LUH018DWEDXXX-00-0723.indd 13 7/18/23 1:53 PM7/18/23 1:53 PM

WARRANTY
13
WARRANTY
ANY ATTEMPT TO SELF-SERVICE YOUR DEVICE, UNLESS INSTRUCTED BY LEXINGTON
INTERNATIONAL CUSTOMER SERVICE, WILL VOID YOUR WARRANTY
To validate your warranty, please register online at: www.actonis.com/warranty
THE DEVICE IS WARRANTED BY LEXINGTON INTERNATIONAL, LLC (“LEXINGTON”) AGAINST
DEFECTS IN MATERIALS OR WORKMANSHIP FOR 12 MONTHS FROM DATE OF PURCHASE. IF
THIS PRODUCT IS DETERMINED TO BE DEFECTIVE, LEXINGTON WILL REPAIR OR REPLACE IT,
AT ITS OPTION, AT NO CHARGE DURING THE WARRANTY PERIOD. THE WARRANTY PERIOD IS
NOT EXTENDED IF LEXINGTON REPAIRS OR REPLACES THE PRODUCT. AFTER THE WARRANTY
PERIOD, THE USER MUST PAY FOR ALL PARTS AND LABOR CHARGES. IF THE PRODUCT IS
REPAIRED OR REPLACED, EITHER WITHIN OR OUTSIDE THE WARRANTY PERIOD, LEXINGTON
RESERVES THE RIGHT TO PROVIDE EQUIVALENT PARTS IN DIFFERENT COLORS TO YOUR
ORIGINAL PRODUCT.
THIS WARRANTY DOES NOT COVER DAMAGES CAUSED BY ACTS OF GOD, MISUSE,
NEGLIGENCE, ACCIDENT, MODIFICATION OF OR TO ANY PART OF THE PRODUCT. THIS
WARRANTY DOES NOT COVER DAMAGE DUE TO IMPROPER OPERATION OR MAINTENANCE,
CONNECTION TO IMPROPER VOLTAGE SUPPLY, OR ATTEMPTED REPAIR BY ANYONE OTHER
THAN LEXINGTON. THIS WARRANTY IS VOID IF PRODUCT IS TAMPERED WITH.
TO OBTAIN WARRANTY SERVICE, YOU MUST CALL LEXINGTON INTERNATIONAL CUSTOMER
SERVICE TO REQUEST AN AUTHORIZATION NUMBER. YOU MUST DELIVER THE PRODUCT
FREIGHT PREPAID, IN EITHER ITS ORIGINAL PACKAGING OR PACKAGING AFFORDING
AN EQUAL DEGREE OF PROTECTION, TOGETHER WITH YOUR NAME, ADDRESS AND
AUTHORIZATION NUMBER, TO:
Lexington International, LLC, 1040 Holland Drive, Boca Raton, FL 33487, USA
LEXINGTON INTERNATIONAL, LLC SHALL NOT BE LIABLE FOR ANY SPECIAL, PUNITIVE,
INCIDENTAL OR CONSEQUENTIAL DAMAGES THAT ARE DIRECTLY OR INDIRECTLY
RELATED TO THE USE OF, OR THE INABILITY TO USE, THE PRODUCT, EVEN IF LEXINGTON
INTERNATIONAL, LLC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES WHETHER
IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTUOUS ACTION. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF SPECIAL, PUNITIVE, INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU. THIS WARRANTY IS THE ONLY WRITTEN OR EXPRESS WARRANTY GIVEN BY LEXINGTON
INTERNATIONAL, LLC. ALL IMPLIED WARRANTIES FOR THE PRODUCT, INCLUDING BUT
NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN TIME TO THE TERM OF THIS WARRANTY. SOME STATES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
GOVERNING LAW; JURISDICTION AND VENUE: THIS WARRANTY, AND THE TERMS OF SALE OF
THE PRODUCT, SHALL BE GOVERNED BY AND CONSTRUED IN ACCORDANCE WITH THE LAWS
OF THE STATE OF FLORIDA WITHOUT REGARD TO PRINCIPLES OF CONFLICTS OF LAWS. THE
PARTIES IRREVOCABLY SUBMIT AND CONSENT TO THE SOLE AND EXCLUSIVE JURISDICTION
AND VENUE OF THE FLORIDA STATE COURTS IN AND FOR PALM BEACH COUNTY, FLORIDA,
U.S.A. AND THE FEDERAL COURTS IN AND FOR THE SOUTHERN DISTRICT OF FLORIDA, U.S.A.
THE PARTIES AGREE NOT TO RAISE THE DEFENSE OF FORUM NON CONVENIENS.
WARRANTY OUTSIDE THE U.S.A.
THE WARRANTY ON THIS PRODUCT SHALL COMPLY WITH APPLICABLE LAW WHEN SOLD BY
AN AUTHORIZED DEALER TO A CONSUMER OUTSIDE OF THE UNITED STATES, INCLUDING
EXTENDED WARRANTY COVERAGE PERIODS AS MAY BE LEGALLY REQUIRED IN SUCH
JURISDICTIONS.
AUTHORIZED REPRESENTATIVE IN EUROPE (REGULATORY AFFAIRS ONLY):
TEL: [phone] FAX: [phone]
Westervoortsedijk 60
6827 AT Arnhem
The Netherlands
LUH018DWEDXXX-00-0723.indd 14LUH018DWEDXXX-00-0723.indd 14 7/18/23 1:53 PM7/18/23 1:53 PM

14
LUH018DWEDXXX-00-0723.indd 15LUH018DWEDXXX-00-0723.indd 15 7/18/23 1:53 PM7/18/23 1:53 PM

LUH018DWEDXXX 00 0723
LEXINGTON INTERNATIONAL, LLC
1040 Holland Drive | Boca Raton, Florida | 33487 | USA
www.actonis.com
Australian Sponsor:
Emergo Australia
Level 20, Tower II Darling Park,
201 Sussex Street Sydney,
NSW 2000 Australia
Authorized Representative in Europe
(Regulatory Affairs Only):
Tel: [phone] Fax: [phone]
CUSTOMER SERVICE
TOLL-FREE NUMBERS
United States and Canada 1-866-527-3726
United Kingdom 0808-134-9868
Australia 61 7 3198 2484
France 805-081-824
Spain 900-838-164
Mexico 01 800 953 0209
Italy 800 694 205
Germany 800 001 0163
Westervoortsedijk 60
6827 AT Arnhem
The Netherlands
LUH018DWEDXXX-00-0723.indd 16LUH018DWEDXXX-00-0723.indd 16 7/18/23 1:53 PM7/18/23 1:53 PM