ACU-RITE Intelli-Time 13019W2 User manual

Intelli-Time® Alarm Clock
model 13019W2
CONTENTS
Unpacking Instructions 2
Package Contents 2
Product Registration 2
Features &Benefrts 3
Clock Setup .4
Intelli-Time® Clock .4
Set the Time & Date .4
Using the Alarm Clock 5
Troubleshooting 5
Care & Maintenance 6
Replace Intelli-Time® BaHery 6
Specifrcations 6
FCC Information 6
Customer Support 7
Warranty 7
Questions? Contact Customer Support at
[phone] or visit www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.

Congratulations on your new AcuRite product. To ensure the best
possible product performance, please read this manual in its entirety
and retain it for future reference.
Unpacking Instructions
Removethe protective film that is applied to the LCDscreen prior to usingthis
product. Locate the tab and peel off to remove.
Package Contents
1.Alarm clock
2. Instruction Manual
PRODUCT REGISTRATION
Register online
to receive 1 year
warranty protection
www.AcuRite.com
2
Features & Benefits
82
1. ALARMON/OFF Button
2. ALARMSETButton
3. "+" Button
4. ALARMON Icon
5. PM Indicator
6. SNOOZE Button
7. "-" Button
8. TIME SETButton
9. DSTON/OFF Switch
10. RESETButton
Full reset to factory
defaults
11. TIME ZONE Switch
12. Dimmer HI/LO Switch
13. Intelli·Time® Battery
Compartment
14. VOLUME HI/LO Switch
9
10 11
3

- SETUP
Clock Setup
Plug the power cord into power outlet.
Intelli-Time® Clock
Intelli-Time clock and calendar are pre-programmed to the correct time and
date, and update automatically for Daylight Savings Time. All you need to do
is select your time zone using the "TIME ZONE" switch.
Set the Time & Date
Choose the correct time zone (HAST AKST PST MST CST EST AST) using the
"TIME ZONE" switch on the bottom of the clock.
Choose Daylight Savings Time ON or OFF using the DST switch on the bottom
of the clock. If you live in an area that observes Daylight Savings Time, DST
should be set to ON, even if it is not currently Daylight Savings Time.
Press and hold the "TIME SET" button for 3 seconds to enter the SET MODE.
Once in the SET MODE the preference you are currently in will blink on the clock.
To save your adjustments, press and release the "TIME SET" button to adjust
the next preference. The preference order is as follows:
CLOCK HOUR (Please note PM Indicator light)
CLOCK MINUTE
CALENDAR YEAR
CALENDAR MONTH
CALENDAR DATE
You will automatically exit SET MODE if no buttons are pressed
for 30 seconds. Enter SET MODE any time by pressing and holding
"TIME SET" button for 3 seconds.
Dimmer HI/LO
Optimize the display brightness for the location with the HI/LO Dimmer switch
located on the back of the clock.
Volume HI/LO
Optimize the alarm volume for the location with the Volume HI/LO switch
located on the back of the clock.
4
OPERATION
Using the Alarm Clock
Set the Alarm Time
To set alarm time, press the "ALARM SET" button once to review alarm time.
Press the "ALARM SET" button again to enter ALARM SET MODE.
To adjust the currently selected (flashing) item, press and release the "+" or
"-" buttons (press and HOLD to fast adjust).
To save your adjustments, press and release the "ALARM SET" button to adjust
the next preference. The preference set order is as follows:
ALARM CLOCK HOUR (Please note PM Indicator light)
ALARM CLOCK MINUTE
You will' automatically exit ALARM SET MODE if no buttons are pressed
for 30 seconds. Enter ALARM SET MODE at any time by pressing the
"ALARM SET" button twice.
Alarm Clock ON or OFFfunction
To Turn Alarm on: Press the "ALARM ON/OFF" button until the
ALARM ON icon appears on the screen.
To Turn Alarm off: Press the "ALARM ON/OFF" button until the
ALARM ON icon disappears from the screen.
Alarm Clock SNOOZEfunction
When the alarm is sounding, activate the 9 minute SNOOZE function by
pressing the SNOOZE button on the top of the alarm clock. SNOOZE
function remains active until ALARM ON/OFF button is pressed.
Troubleshooting
Clockis too dark, • Reset the unit by pressing the reset button located on
the bottom of the clock. This will reset the alarm to the
hard to read or original factory settings. Time and date will need to be
doesn't work entered after a reset.
If your AcuRiteproduct does not operate properly after trying
the troubleshooting steps, visit www.AcuRite.com or call
(877) 221·1252 for assistance.
5

Care & Maintenance
Clock Care
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep
away from dust, dirt and moisture. Clean ventitation ports regularly with a
gentle' puff of air.
Replace Intelli-Time Clock Battery
Intelli-Timetechnology is powered
by a pre-installed coin-cell battery
that stores the time and date
settings. The battery has a shelf
life of several years. To replace
the Intelli-Time battery:
1. Locate the coin cell battery
compartment door on the back
of the display unit. Unscrew and
remove the compartment cover.
2. Insert 1 x CR2032 coin cell battery into the battery compartment, as shown.
Install battery with "+" positive terminal facing OUT.
3. Screw in the battery cover.
WARNING: THIS PRODUCT CONTAINS A BUTTON-CELL BATTERY. IF SWALLOWED, IT~
COULD CAUSE SEVERE INJURY OR DEATH IN JUST 2 HOURS. 111.
SEEK MEDICAL ATTENTION IMMEDIATELY IF INGESTED. ~
N PO"ON
Specifications
I POWER
I AC power cord (120V)
FCCInformation
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
1·This device may NOT couse harmful interference, and
2· This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: Thisequipment has been tested and found to comply with the limits for a Closs B digital device, pursuant to Port 15 of the
FCC rules. These limits are designed to provide reasonable protection against harmful interFerence in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc:
tions, may couse harmful interference to radio communicahons. However, There is no guarantee that interference will not occur In a
particular installation. Ifthis equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into on outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for hel~.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
Such modifications could void the user authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS stcndordls].
Ore ration is subject to the following two conditions:
1 Thisdevice may not cause interference, and
b Thisdevice must accept any interference received, including interference that may cause undesired operation of the device.
6
Customer Support
AcuRite customer support is committed to providing you with best-in-
class service. For assistance, please have the model number of this
product available and contact us in any of the following ways:
(() [phone] @[email protected]
24/7 support at www.AcuRite.com
~ Installation Videos
~ Instruction Manuals
~ Register your Product
~ Support User Forum
~ Submit Feedback & Ideas.,. Replacement Parts
PRODUCT REGISTRATION
Register online
to receive 1 year
warranty protection
www.AcuRite.com
/-("I'l','t"'j Pro·.1ucts
~Register a Product
Limited One Year Warranty
At AcuRite, we proudly uphold our commitment
to quality technology. Chaney Instrument Co.
warrants that all products it manufactures to
be of good material and workmanship, and to
be free of defects when rroperly installed and
operated for a period 0 one year from the date
of purchase.
We recommend that you visit us at
www.AcuRite.com for the fastest way to register
your product. However, product registration
does not eliminate the need to retain your
original proof of purchase in order to obtain
warranty benefits.
Chaney Instrument Co. warrants that all products it manufactures
to be of good material and workmanship, and to be free of
defect, when properly tnstclled and operated for a period of
one year from the dote of purchase. Remedy for breach of this
warranty is limited to repair or replacement of the defective
itemis]. Any product which, under normal use and service, is
proven to breach the warranty contained herein within ONE
YEARfrom date of sale will, vpon examination by Chaney,
and at its sale option, be repaired or replaced by Chaney.
Transportation costs and charges for returned goods shall
be paid for by the purchaser. Chaney hereby disclaims all
responsibility for such transportation costs and charges. This
warronty will not be breached, and Chaney will give no credit
for products it manuFactures which have received normal wear
end to,,,, boon damaged (including by act, of nature), tampered,
cbosed, Improperly installed, damaged in shipping, or repaired
or Clltol'od by others then authorized representatives of Chaney.
Tho cbcvo-described warranty ls expressly in lieu of all other
warrantios, express or' implied, end all other warranties are
hereby expressly disclclmcd, including without limitation the
implied warranty of morchantability and the implied warranty
of fitness for a particular purpose. Chaney expressly disclaims
all liability for special, consoquontial or incidental damages,
whether arising in tort or by contract from any breach of this
warranty. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation
or exclusion may not apply to you. Chanoy further disclcims all
liability from personal injury "elating to its products to the extent
permitted by low. Byacceptance of any of Chaney', product"
the purchaser assumes all liability for the consequences arising
From their use or misuse. No person, firm or corporation is
authorized to assume for Chaney any other liability in connection
with the sale of its products. Furthermore, no person, firm or
corporation is authorized to modify or waive the terms of this
paragraph, and the preceding paragraph, unless done in writing
and ,igned by a duly authorized agent of Chaney. This warranty
gives you specific legal rights, and you may also have other
rights which vary from stote to state.
For ln-wcrrcnty claims: Chaney Instrument Co.
965 Wells St., Lake Geneva, WI 53147
7